Luke Jurmu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Luke Jurmu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Jason Blough
Michigan Technological University
3 shared publicationsCraig Reynolds
General Motors Company
2 shared publicationsDarrell Robinette
Michigan Technological University
2 shared publications- Darrell Robinette
Department of Mechanical and Aerospace Engineering, Michigan Technological University, Houghton, MI 49931, USA
2 shared publications - C. Reynolds
General Motors Company, Detroit, USA
1 shared publication Eric Mordorski
Michigan Technological University
1 shared publication
Latest Publications
- 8 December 2024
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (5-6) , 860-876
In situ torque transmissibility frequency response function measurements of a centrifugal pendulum vibration absorber in a torque converter clutch damper
This investigation details torsional testing and characterization of torque converter clutch (TCC) damper variants containing centrifugal pendulum absorbers (CPAs) utilized in light duty production vehicles. Data collected on a torque converter dynamometer test stand was used to correlate a nonlinear model of the combination TCC damper and CPA when locked with zero relative slip speed. The range of test torques and speeds are related to when driveline, chassis and body noise and vibration concerns are high and the damper-CPA combination are required to provide maximum isolation. To facilitate model correlation efforts, modified configurations of the same torque converter design were procured, enabling separation of damping effects from the CPA and damper springs. Under load, the locked TCC was torsionally excited to acquire torque transmissibility frequency response functions (TTFRFs). The anti-resonance of the CPA was measured, and the viscous damping coefficient estimated. A manual tuning and modified half-power bandwidth method were used to estimate the equivalent viscous damping of the CPA. Additional test cases included torsional excitation amplitude and oil temperature to ascertain differences in CPA response and tuning order. The objective of the investigation is to demonstrate the influence of damper spring and CPA integration, extraction of CPA damping from actual hardware and the utility of including representative damping in model-based design of future damper-CPA assemblies.
- 8 December 2024
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 32 (5-6) , 860-876
In situ torque transmissibility frequency response function measurements of a centrifugal pendulum vibration absorber in a torque converter clutch damper
This investigation details torsional testing and characterization of torque converter clutch (TCC) damper variants containing centrifugal pendulum absorbers (CPAs) utilized in light duty production vehicles. Data collected on a torque converter dynamometer test stand was used to correlate a nonlinear model of the combination TCC damper and CPA when locked with zero relative slip speed. The range of test torques and speeds are related to when driveline, chassis and body noise and vibration concerns are high and the damper-CPA combination are required to provide maximum isolation. To facilitate model correlation efforts, modified configurations of the same torque converter design were procured, enabling separation of damping effects from the CPA and damper springs. Under load, the locked TCC was torsionally excited to acquire torque transmissibility frequency response functions (TTFRFs). The anti-resonance of the CPA was measured, and the viscous damping coefficient estimated. A manual tuning and modified half-power bandwidth method were used to estimate the equivalent viscous damping of the CPA. Additional test cases included torsional excitation amplitude and oil temperature to ascertain differences in CPA response and tuning order. The objective of the investigation is to demonstrate the influence of damper spring and CPA integration, extraction of CPA damping from actual hardware and the utility of including representative damping in model-based design of future damper-CPA assemblies.
- 24 September 2020
- Published by Springer Nature
- p. 17-25
Measurement Methods for Evaluating the Frequency Response Function of a Torque Converter Clutch
- 24 September 2020
- Published by Springer Nature
- p. 17-25
Measurement Methods for Evaluating the Frequency Response Function of a Torque Converter Clutch
- 23 July 2020
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 27 (13-14) , 1498-1510
Design and test of a torsional vibration absorber in series with a planetary gearset
Traditional vibration absorbers have not often been a practical solution for attenuating low frequency drivetrain modes of vibration because of the combination of the large mass and inertia and/or low stiffness, required to tune to the desired frequency. With the goal of reducing the inertia and size of a torsional vibration absorber, a unique vibration absorber was developed. Using a planetary gearset, the effective inertia of the absorber was increased without changing its physical mass, and a torsional mode below 30 Hz was successfully attenuated with physically realizable inertia and stiffness parameters. By reducing the tuned mass, the total volume claimed by the vibration absorber and planetary gearset was up to three times less than an equivalent traditional vibration absorber. A lumped parameter torsional model was developed to determine the optimal configuration of the planetary gearset input, output, and absorber inertia as well as a method to predict the optimal tuning frequency of the planetary torsional vibration absorber. A drivetrain dynamometer setup which emulates a two-degree-of-freedom torsional system was used to experimentally test and validate the performance of two planetary torsional vibration absorber prototypes built based upon the results of the lumped parameter model. The dynamometer setup was designed to have a first torsional mode around 20 Hz in which the planetary torsional vibration absorber was designed to attenuate. Based upon the experimental results of the planetary torsional vibration absorber, a reduction of over 20 dB was achieved.
- 23 July 2020
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 27 (13-14) , 1498-1510
Design and test of a torsional vibration absorber in series with a planetary gearset
Traditional vibration absorbers have not often been a practical solution for attenuating low frequency drivetrain modes of vibration because of the combination of the large mass and inertia and/or low stiffness, required to tune to the desired frequency. With the goal of reducing the inertia and size of a torsional vibration absorber, a unique vibration absorber was developed. Using a planetary gearset, the effective inertia of the absorber was increased without changing its physical mass, and a torsional mode below 30 Hz was successfully attenuated with physically realizable inertia and stiffness parameters. By reducing the tuned mass, the total volume claimed by the vibration absorber and planetary gearset was up to three times less than an equivalent traditional vibration absorber. A lumped parameter torsional model was developed to determine the optimal configuration of the planetary gearset input, output, and absorber inertia as well as a method to predict the optimal tuning frequency of the planetary torsional vibration absorber. A drivetrain dynamometer setup which emulates a two-degree-of-freedom torsional system was used to experimentally test and validate the performance of two planetary torsional vibration absorber prototypes built based upon the results of the lumped parameter model. The dynamometer setup was designed to have a first torsional mode around 20 Hz in which the planetary torsional vibration absorber was designed to attenuate. Based upon the experimental results of the planetary torsional vibration absorber, a reduction of over 20 dB was achieved.