Rui Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rui Li has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Ji Wang
School of Naval Architecture and Ocean Engineering, Dalian University of Technology, Dalian 116024, China
16 shared publications - Yujun Liu
School of Naval Architecture and Ocean Engineering, Dalian University of Technology, Dalian 116024, China
8 shared publications - Shun Wang
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
5 shared publications - Zhikang Xu
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
4 shared publications - Jiayan Wang
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
3 shared publications - Jinliang Dai
Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China
3 shared publications
Latest Publications
- Open Access
Improved CNN for Predicting Line Heating Forming Deformation of Complex Hull Curved Plate
Shipbuilding requires numerous complex curved plates, with manual line heating forming as the primary processing method for the outer plates of the hull. To solve the problem of automation in curved plate forming, this research investigates intelligent deformation prediction for hull curved plate based on improved convolutional neural network (CNN). A numerical calculation model based on the strain direct boundary was established. The feasibility of the model was verified by comparing finite element numerical calculation results with experimental data. To achieve fast prediction of curved plate forming, a deformation prediction model for curved plate forming based on CNN was established. To further enhance the prediction accuracy of the CNN model, particle swarm optimization (PSO) and whale migration algorithm (WMA) were introduced to improve the weights of CNN, PSO-CNN model, and WMA-CNN model were established. Compared with the CNN model, the MAPE of the PSO-CNN model and the WMA-CNN model decreased by 0.31 and 1.36, respectively, for predicting the shrinkage. The MAPE decreased by 1.31 and 4.05, respectively, for predicting the deflection. This results in the WMA-CNN model effectively improving the prediction accuracy compared with the CNN model and PSO-CNN model. The WMA-CNN model is applied for the validation of the case. The relative error of the cases is all within 5%, indicating that the WMA-CNN model is applicable to the intelligent prediction of curved plate forming. This research provides reference for automation forming of hull curved plate.
Open AccessImproved CNN for Predicting Line Heating Forming Deformation of Complex Hull Curved Plate
Shipbuilding requires numerous complex curved plates, with manual line heating forming as the primary processing method for the outer plates of the hull. To solve the problem of automation in curved plate forming, this research investigates intelligent deformation prediction for hull curved plate based on improved convolutional neural network (CNN). A numerical calculation model based on the strain direct boundary was established. The feasibility of the model was verified by comparing finite element numerical calculation results with experimental data. To achieve fast prediction of curved plate forming, a deformation prediction model for curved plate forming based on CNN was established. To further enhance the prediction accuracy of the CNN model, particle swarm optimization (PSO) and whale migration algorithm (WMA) were introduced to improve the weights of CNN, PSO-CNN model, and WMA-CNN model were established. Compared with the CNN model, the MAPE of the PSO-CNN model and the WMA-CNN model decreased by 0.31 and 1.36, respectively, for predicting the shrinkage. The MAPE decreased by 1.31 and 4.05, respectively, for predicting the deflection. This results in the WMA-CNN model effectively improving the prediction accuracy compared with the CNN model and PSO-CNN model. The WMA-CNN model is applied for the validation of the case. The relative error of the cases is all within 5%, indicating that the WMA-CNN model is applicable to the intelligent prediction of curved plate forming. This research provides reference for automation forming of hull curved plate.
- Open Access
- 13 June 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (6) , 1169
A Computational Study on the Excitation Forces of Partially Submerged Propellers for High-Speed Boats
During high-speed navigation, boat propellers often become partially exposed due to elevated sailing speeds. This condition results in a unique operational scenario where propellers are only partially submerged. Conducting computational studies on the excitation of propellers under such circumstances is essential for optimizing the dynamic performance of the shafting system. A theoretical calculation method for propeller performance was developed based on the principles of fluid dynamics relevant to water entry, leading to a computational method for determining excitation forces in this specific operational condition. This method was subsequently refined through appropriate adjustments using ANSYS Fluent software to simulate the behavior of partially submerged propellers. The findings highlighted the accuracy of the proposed model in predicting the pulsation of six force components across three distinct directions: along the propeller shaft, vertical, and lateral. Specifically, for a single blade (Blade 1), the pulsation amplitude of the vertical force (Fx) constituted 82.1% of its maximum peak magnitude and equated to 57.5% of the blade’s mean thrust. Analogously, the lateral force (Fz) pulsation amplitude represented 53.3% of its maximum peak magnitude and 40.0% of the mean thrust. These findings indicate the presence of significant unsteady hydrodynamic loads. Furthermore, a visualization approach was presented to analyze blade load phasing, offering insights relevant to the arrangement of blades on partially submerged propellers.
- 13 June 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (6) , 1169
Open AccessA Computational Study on the Excitation Forces of Partially Submerged Propellers for High-Speed Boats
During high-speed navigation, boat propellers often become partially exposed due to elevated sailing speeds. This condition results in a unique operational scenario where propellers are only partially submerged. Conducting computational studies on the excitation of propellers under such circumstances is essential for optimizing the dynamic performance of the shafting system. A theoretical calculation method for propeller performance was developed based on the principles of fluid dynamics relevant to water entry, leading to a computational method for determining excitation forces in this specific operational condition. This method was subsequently refined through appropriate adjustments using ANSYS Fluent software to simulate the behavior of partially submerged propellers. The findings highlighted the accuracy of the proposed model in predicting the pulsation of six force components across three distinct directions: along the propeller shaft, vertical, and lateral. Specifically, for a single blade (Blade 1), the pulsation amplitude of the vertical force (Fx) constituted 82.1% of its maximum peak magnitude and equated to 57.5% of the blade’s mean thrust. Analogously, the lateral force (Fz) pulsation amplitude represented 53.3% of its maximum peak magnitude and 40.0% of the mean thrust. These findings indicate the presence of significant unsteady hydrodynamic loads. Furthermore, a visualization approach was presented to analyze blade load phasing, offering insights relevant to the arrangement of blades on partially submerged propellers.
- Open Access
- 27 May 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (6) , 1057
Research on the Forming Detection Technology of Shell Plates Based on Laser Scanning
In order to solve the problems of low efficiency and insufficient accuracy of the traditional manual template method in the forming detection of shell plates, a digital solution based on laser scanning detection system was proposed. By introducing a six-degree-of-freedom robotic arm and a high-precision line laser sensor to build a three-dimensional detection platform, a digital template method framework including data acquisition, point cloud registration, surface reconstruction, and deviation analysis was innovatively constructed. A point cloud non-penetration registration algorithm fused with boundary geometric information was proposed. Based on the improved Delaunay triangulation algorithm, the surface is reconstructed and the digital template is extracted. Experimental verification shows that the method achieves an accuracy of less than 1 mm of error in the detection of outer plates, shortens the single detection time to less than 10 min, and improves the detection efficiency by more than 75% compared with the traditional method.
- 27 May 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (6) , 1057
Open AccessResearch on the Forming Detection Technology of Shell Plates Based on Laser Scanning
In order to solve the problems of low efficiency and insufficient accuracy of the traditional manual template method in the forming detection of shell plates, a digital solution based on laser scanning detection system was proposed. By introducing a six-degree-of-freedom robotic arm and a high-precision line laser sensor to build a three-dimensional detection platform, a digital template method framework including data acquisition, point cloud registration, surface reconstruction, and deviation analysis was innovatively constructed. A point cloud non-penetration registration algorithm fused with boundary geometric information was proposed. Based on the improved Delaunay triangulation algorithm, the surface is reconstructed and the digital template is extracted. Experimental verification shows that the method achieves an accuracy of less than 1 mm of error in the detection of outer plates, shortens the single detection time to less than 10 min, and improves the detection efficiency by more than 75% compared with the traditional method.
- Open Access
- 31 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (2) , 270
Dynamic Characteristics of Bidirectional Misaligned Marine Water-Lubricated Bearings Considering Turbulence, Surface Roughness and Bush Deformation
The marine water-lubricated bearing’s (WLBs) dynamic properties are essential for ensuring the shaft system’s operational dependability. The coupled model of mixed lubrication and turbulence under the impact of bidirectional misalignment is proposed in this research, and the perturbation equations of marine WLBs with 32 coefficients are derived. The finite difference method (FDM) is used to solve the steady-state and perturbation equations, and the impacts of turbulence, bearing bush deformation, surface roughness, and bidirectional shaft misalignment on the dynamic characteristics of the WLBs are systematically investigated. The results reveal that under mixed lubrication, surface roughness and the turbulence effect can both greatly improve the stiffness and damping of the bearings, but that there is a threshold phenomenon for the turbulence effect’s influence on these properties. Neglecting the elastic deformation of the bush may lead to an overestimation of the bearings’ stiffness and damping, causing substantial inaccuracies in conditions of heavy load or declined Young’s modulus. The 32 coefficients of the WLB exhibit considerable variation with the misalignment angle; hence, a more comprehensive dynamic model should be developed for misaligned marine WLBs. The study’s findings provide valuable insights for rotor dynamics research and optimal design of lubrication performance in marine WLBs.
- 31 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (2) , 270
Open AccessDynamic Characteristics of Bidirectional Misaligned Marine Water-Lubricated Bearings Considering Turbulence, Surface Roughness and Bush Deformation
The marine water-lubricated bearing’s (WLBs) dynamic properties are essential for ensuring the shaft system’s operational dependability. The coupled model of mixed lubrication and turbulence under the impact of bidirectional misalignment is proposed in this research, and the perturbation equations of marine WLBs with 32 coefficients are derived. The finite difference method (FDM) is used to solve the steady-state and perturbation equations, and the impacts of turbulence, bearing bush deformation, surface roughness, and bidirectional shaft misalignment on the dynamic characteristics of the WLBs are systematically investigated. The results reveal that under mixed lubrication, surface roughness and the turbulence effect can both greatly improve the stiffness and damping of the bearings, but that there is a threshold phenomenon for the turbulence effect’s influence on these properties. Neglecting the elastic deformation of the bush may lead to an overestimation of the bearings’ stiffness and damping, causing substantial inaccuracies in conditions of heavy load or declined Young’s modulus. The 32 coefficients of the WLB exhibit considerable variation with the misalignment angle; hence, a more comprehensive dynamic model should be developed for misaligned marine WLBs. The study’s findings provide valuable insights for rotor dynamics research and optimal design of lubrication performance in marine WLBs.
- 3 September 2024
- Published by Elsevier in Ocean Engineering
- Vol. 312
A method for accurate extraction of three-dimensional point cloud feature data in loading test of container ships
- 3 September 2024
- Published by Elsevier in Ocean Engineering
- Vol. 312
A method for accurate extraction of three-dimensional point cloud feature data in loading test of container ships
- 27 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 312
A novel 4-DOF marine stern bearing support model considering discrete distribution effects
- 27 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 312
A novel 4-DOF marine stern bearing support model considering discrete distribution effects
- Open Access
- 1 May 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Development of multi-functional integrated design system for ship block lifting process
- 1 May 2024
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 16
Open AccessDevelopment of multi-functional integrated design system for ship block lifting process
- Open Access
- 31 January 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (2) , 255
Deformation Intelligent Prediction of Titanium Alloy Plate Forming Based on BP Neural Network and Sparrow Search Algorithm
The application of titanium alloy in shipbuilding can reduce ship weight and carbon emissions. To solve the problem of titanium alloy forming, the deformation prediction of titanium alloy line heating based on a backpropagation (BP) neural network and sparrow search algorithm (SSA) was researched. Based on the thermal–elastic–plastic finite element method, the numerical calculation model of TA5 titanium alloy overlapping heating forming was established. The feasibility of the model was verified by comparing it with the numerical calculation and experiment of low-carbon steel. Considering the characteristics of the titanium alloy-forming process, 73 groups of titanium alloy-forming schemes were obtained by the Latin hypercube sampling method. The deformation data of the samples were obtained by using the numerical calculation model of titanium alloy forming. The prediction methods of titanium alloy-forming deformation based on BP, genetic algorithm–backpropagation (GA-BP), and SSA-BP were proposed. The accuracy of different neural network prediction models was analyzed. The mean absolute percentage errors (MAPEs) of BP, GA-BP, and SSA-BP in shrinkage prediction were 7.45%, 4.08%, and 2.96%, respectively. The MAPEs of BP, GA-BP, and SSA-BP in deflection prediction were 8.44%, 4.73%, and 2.64%, respectively. The goodness of fit (R2) of SSA-BP is closest to 1 among the three models. The calculation results show that SSA-BP is better than BP and GA-BP in predicting the forming deformation of titanium alloy. The maximum prediction error of SSA-BP is 4.95%, which is within the allowable range of engineering error. The SSA-BP prediction model is suitable for the rapid and accurate prediction of the deformation of titanium alloy line heating forming. The intelligent prediction model provides data support for intelligent decisions for titanium alloy forming.
- 31 January 2024
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 12 (2) , 255
Open AccessDeformation Intelligent Prediction of Titanium Alloy Plate Forming Based on BP Neural Network and Sparrow Search Algorithm
The application of titanium alloy in shipbuilding can reduce ship weight and carbon emissions. To solve the problem of titanium alloy forming, the deformation prediction of titanium alloy line heating based on a backpropagation (BP) neural network and sparrow search algorithm (SSA) was researched. Based on the thermal–elastic–plastic finite element method, the numerical calculation model of TA5 titanium alloy overlapping heating forming was established. The feasibility of the model was verified by comparing it with the numerical calculation and experiment of low-carbon steel. Considering the characteristics of the titanium alloy-forming process, 73 groups of titanium alloy-forming schemes were obtained by the Latin hypercube sampling method. The deformation data of the samples were obtained by using the numerical calculation model of titanium alloy forming. The prediction methods of titanium alloy-forming deformation based on BP, genetic algorithm–backpropagation (GA-BP), and SSA-BP were proposed. The accuracy of different neural network prediction models was analyzed. The mean absolute percentage errors (MAPEs) of BP, GA-BP, and SSA-BP in shrinkage prediction were 7.45%, 4.08%, and 2.96%, respectively. The MAPEs of BP, GA-BP, and SSA-BP in deflection prediction were 8.44%, 4.73%, and 2.64%, respectively. The goodness of fit (R2) of SSA-BP is closest to 1 among the three models. The calculation results show that SSA-BP is better than BP and GA-BP in predicting the forming deformation of titanium alloy. The maximum prediction error of SSA-BP is 4.95%, which is within the allowable range of engineering error. The SSA-BP prediction model is suitable for the rapid and accurate prediction of the deformation of titanium alloy line heating forming. The intelligent prediction model provides data support for intelligent decisions for titanium alloy forming.
- Open Access
- 28 November 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2248
A Pre-Procession Module for Point-Based Deep Learning in Dense Point Clouds in the Ship Engineering Field
Recently, point cloud technology has been applied in the ship engineering field. However, the dense point cloud acquired by terrestrial laser scanning (TLS) technology in ship engineering applications brings an obstacle to some powerful and advanced point-based deep learning point cloud processing methods. This paper presents a deep learning pre-procession module to ensure the feasibility of processing dense point clouds on commonly available computer devices. The pre-procession module is designed according to the traditional point cloud processing methods and the PointNet++ paradigm, and is evaluated on two ship structure datasets and two popular point cloud datasets. Experimental results illustrate that (i) the proposed module improves the performance of point-based deep learning semantic segmentation networks, and (ii) the proposed module empowers the existing point-based deep learning networks with the capability to process dense input point clouds. The proposed module may provide a useful semantic segmentation tool for realistic dense point clouds in various industrial applications.
- 28 November 2023
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 11 (12) , 2248
Open AccessA Pre-Procession Module for Point-Based Deep Learning in Dense Point Clouds in the Ship Engineering Field
Recently, point cloud technology has been applied in the ship engineering field. However, the dense point cloud acquired by terrestrial laser scanning (TLS) technology in ship engineering applications brings an obstacle to some powerful and advanced point-based deep learning point cloud processing methods. This paper presents a deep learning pre-procession module to ensure the feasibility of processing dense point clouds on commonly available computer devices. The pre-procession module is designed according to the traditional point cloud processing methods and the PointNet++ paradigm, and is evaluated on two ship structure datasets and two popular point cloud datasets. Experimental results illustrate that (i) the proposed module improves the performance of point-based deep learning semantic segmentation networks, and (ii) the proposed module empowers the existing point-based deep learning networks with the capability to process dense input point clouds. The proposed module may provide a useful semantic segmentation tool for realistic dense point clouds in various industrial applications.
- Open Access
Deflection Intelligent Prediction for High-Strength Steel Saddle Plate Forming Applicable to Reducing Ship Weight
The application of high-strength steel plates can reduce ship weight, and the saddle plate is one of the most common types of double-curved hull plates. To fill the research gap regarding high-strength steel saddle plates, two prediction models are established here to predict deformation in saddle plate forming. Deflection is a key parameter reflecting the overall deformation of a curved plate. Therefore, first of all, the influencing factors of the line heating of high-strength steel saddle plates were analyzed. The influence of plate geometric parameters and forming parameters on deflection was researched. Second, a multiple linear regression model between deflection and the geometric parameters and forming parameters of high-strength steel saddle plates was established. Finally, to solve the problem of a large error in the multivariate regression model for extrapolation, an intelligent prediction program for deflection based on a support vector machine (SVM) was developed using the Python language. The results show that the error of the multiple regression model was less than 5% for data interpolation. The error of the intelligent prediction model for deflection was less than 5% for data extrapolation. This research can provide data support for the automatic forming of marine saddle plates.
Open AccessDeflection Intelligent Prediction for High-Strength Steel Saddle Plate Forming Applicable to Reducing Ship Weight
The application of high-strength steel plates can reduce ship weight, and the saddle plate is one of the most common types of double-curved hull plates. To fill the research gap regarding high-strength steel saddle plates, two prediction models are established here to predict deformation in saddle plate forming. Deflection is a key parameter reflecting the overall deformation of a curved plate. Therefore, first of all, the influencing factors of the line heating of high-strength steel saddle plates were analyzed. The influence of plate geometric parameters and forming parameters on deflection was researched. Second, a multiple linear regression model between deflection and the geometric parameters and forming parameters of high-strength steel saddle plates was established. Finally, to solve the problem of a large error in the multivariate regression model for extrapolation, an intelligent prediction program for deflection based on a support vector machine (SVM) was developed using the Python language. The results show that the error of the multiple regression model was less than 5% for data interpolation. The error of the intelligent prediction model for deflection was less than 5% for data extrapolation. This research can provide data support for the automatic forming of marine saddle plates.