Tassiane Apolinário de Oliveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tassiane Apolinário de Oliveira has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ronaldo Alves Medeiros-Junior
Civil Engineering Studies Center (CESEC), Postgraduate Program in Civil Engineering (PPGEC), Federal University of Parana (UFPR), Curitiba, Brazil
3 shared publications - Neusa Aparecida Munhak Beltrame
Universidade Federal do Paraná, Brasil
2 shared publications - Allan Guimarães Borçato
Postgraduate Program in Civil Engineering (PPGEC), Federal University of Parana (UFPR), Curitiba, Brazil.
1 shared publication - Amanda Venancio Trisotto
Universidade Federal do Paraná, Brasil
1 shared publication - Ana Blanco
Loughborough Univ
1 shared publication - Anelize Seniski
Universidade Federal do Paraná – Politécnico/PIPE/UFPR, Curitiba, PR, Brazil
1 shared publication
Latest Publications
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 38 (11) , 04026401
Evaluation of Self-Healing in Metakaolin-Based Geopolymers: Influence of Lime Content and Curing Environments
This study investigates the self-healing performance of metakaolin-based geopolymers incorporating hydrated lime and polyvinyl alcohol fibers (PVA) fibers. Because metakaolin provides a low-calcium matrix, healing mechanisms can be evaluated in isolation, and the gradual addition of hydrated lime enables a controlled assessment of how calcium availability influences healing and strength recovery. In parallel, this study systematically examines how distinct curing environments—air, immersion, and wet–dry cycles—govern the kinetics and stability of healing products, providing and integrated view that remains limited in current literature. Healing efficiency was quantified using two numerical indices—Index of Strength Recovery (ISR) and Index of Crack Sealing (ICS) over a 60-day period, with ISR reaching 87% for the mixture with 20% lime and ICS values between 27% and 37% at 60 days under water exposures. The results reveal that curing conditions and lime content influence healing behavior. Notably, the lime-free mixture demonstrated substantial self-healing, particularly under cyclic exposure, achieving an ICS of 34% and an ISR of 78%, indicating the potential of autogenous healing driven by unreacted aluminosilicates and fiber interaction. Microstructural analyses confirmed the formation of sodium (calcium) aluminosilicate hydrate [N(C)-A-S-H] and carbonate phases and revealed the role of PVA fibers as nucleation sites. These insights advance the understanding of healing mechanisms in metakaolin-based geopolymer binders and support the development of durable, lime-free binders for civil infrastructure applications.
- 1 November 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 38 (11) , 04026401
Evaluation of Self-Healing in Metakaolin-Based Geopolymers: Influence of Lime Content and Curing Environments
This study investigates the self-healing performance of metakaolin-based geopolymers incorporating hydrated lime and polyvinyl alcohol fibers (PVA) fibers. Because metakaolin provides a low-calcium matrix, healing mechanisms can be evaluated in isolation, and the gradual addition of hydrated lime enables a controlled assessment of how calcium availability influences healing and strength recovery. In parallel, this study systematically examines how distinct curing environments—air, immersion, and wet–dry cycles—govern the kinetics and stability of healing products, providing and integrated view that remains limited in current literature. Healing efficiency was quantified using two numerical indices—Index of Strength Recovery (ISR) and Index of Crack Sealing (ICS) over a 60-day period, with ISR reaching 87% for the mixture with 20% lime and ICS values between 27% and 37% at 60 days under water exposures. The results reveal that curing conditions and lime content influence healing behavior. Notably, the lime-free mixture demonstrated substantial self-healing, particularly under cyclic exposure, achieving an ICS of 34% and an ISR of 78%, indicating the potential of autogenous healing driven by unreacted aluminosilicates and fiber interaction. Microstructural analyses confirmed the formation of sodium (calcium) aluminosilicate hydrate [N(C)-A-S-H] and carbonate phases and revealed the role of PVA fibers as nucleation sites. These insights advance the understanding of healing mechanisms in metakaolin-based geopolymer binders and support the development of durable, lime-free binders for civil infrastructure applications.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18107
Effect of carbonation curing and sodium content on geopolymer subjected to sodium and magnesium sulfate attack
Geopolymer cement stands as an alternative to Portland cement to reduce the impacts associated with its production. This material is also affected by ions that can damage its mechanical properties and reduce its durability. Therefore, this research aims to evaluate metakaolin geopolymer concretes attacked by sulfates, both sodium and magnesium. The samples were made by varying the sodium oxide (Na2O) content in the activators on the metakaolin, the curing type, and the water/metakaolin ratio. The specimens were exposed to sodium sulfate, magnesium sulfate, and reference solutions (water) for 10 weeks. The analyses were performed using water absorption (by capillarity and immersion) and compressive strength tests. The results showed that sodium sulfate attack was more aggressive than magnesium sulfate in geopolymer concretes, 91.67% of the samples submitted to sodium sulfate degraded during absorptions tests while 8.33% were degraded by magnesium sulfate. A sodium content of 22% in metakaolin achieved greater resistance to magnesium sulfate attack and curing by carbonation did not improve the properties of the mixtures.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18107
Open AccessEffect of carbonation curing and sodium content on geopolymer subjected to sodium and magnesium sulfate attack
Geopolymer cement stands as an alternative to Portland cement to reduce the impacts associated with its production. This material is also affected by ions that can damage its mechanical properties and reduce its durability. Therefore, this research aims to evaluate metakaolin geopolymer concretes attacked by sulfates, both sodium and magnesium. The samples were made by varying the sodium oxide (Na2O) content in the activators on the metakaolin, the curing type, and the water/metakaolin ratio. The specimens were exposed to sodium sulfate, magnesium sulfate, and reference solutions (water) for 10 weeks. The analyses were performed using water absorption (by capillarity and immersion) and compressive strength tests. The results showed that sodium sulfate attack was more aggressive than magnesium sulfate in geopolymer concretes, 91.67% of the samples submitted to sodium sulfate degraded during absorptions tests while 8.33% were degraded by magnesium sulfate. A sodium content of 22% in metakaolin achieved greater resistance to magnesium sulfate attack and curing by carbonation did not improve the properties of the mixtures.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18101
Microstructure and mechanical properties of geopolymers with different dolomitic lime contents
This study investigated the effect of dolomitic lime incorporation on the microstructure and mechanical properties of metakaolin-based geopolymers activated by alkaline solution. Five geopolymer mixtures were prepared with the addition of 0.0%, 2.5%, 5.0%, 7.5%, and 10.0% dolomitic lime. The microstructure of the geopolymers was evaluated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction analyses (XRD). The compressive strength of the mixtures ranged between 53.2 and 63.0 MPa after 28 days of ambient curing. SEM/EDS analyses showed that the main phases formed were the N-A-S-H gel together with the C-A-S-H and N-M-A-S-H gels in the mixtures with dolomitic lime. In summary, the results showed that the incorporation of dolomitic lime can significantly improve the microstructure and properties of geopolymers.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 18 (1) , e18101
Open AccessMicrostructure and mechanical properties of geopolymers with different dolomitic lime contents
This study investigated the effect of dolomitic lime incorporation on the microstructure and mechanical properties of metakaolin-based geopolymers activated by alkaline solution. Five geopolymer mixtures were prepared with the addition of 0.0%, 2.5%, 5.0%, 7.5%, and 10.0% dolomitic lime. The microstructure of the geopolymers was evaluated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction analyses (XRD). The compressive strength of the mixtures ranged between 53.2 and 63.0 MPa after 28 days of ambient curing. SEM/EDS analyses showed that the main phases formed were the N-A-S-H gel together with the C-A-S-H and N-M-A-S-H gels in the mixtures with dolomitic lime. In summary, the results showed that the incorporation of dolomitic lime can significantly improve the microstructure and properties of geopolymers.
- Open Access
- 28 March 2024
- Published by Centro Universitario de Maringa in Revista em Agronegócio e Meio Ambiente
- Vol. 17 (1) , e11418
Efeitos da substituição parcial do solo por lodo de estação de tratamento de água em tijolos de solo-cimento
Cerca de 75% da água potável no Brasil é produzida em estações de tratamento de água (ETAs) convencionais. Resíduos são gerados neste processo, principalmente o lodo de decantadores (LETA), que segundo estudos é lançado sem tratamento em corpos d'água em 68% dessas instalações. Esta pesquisa avalia a viabilidade da adição de LETA como substituto parcial do solo em tijolos de solo-cimento no traço 1:9 (cimento: solo+LETA). O resíduo foi coletado durante a limpeza dos decantadores da ETA de Toledo-PR. Os tijolos foram produzidos com 5, 10, 15, 25 e 35% de substituição de massa de solo por LETA, além do controle (0%). As moldagens ocorreram em equipamentos industriais para reproduzir ao máximo condições reais de fabricação. Com o aumento do teor de lodo, a resistência à compressão dos tijolos foi reduzida. No entanto, as exigências normativas brasileiras foram atendidas até a adição de 15% de LETA. Houve aumento da absorção de água com o aumento do teor de lodo. No entanto, os tijolos atenderam às exigências regulatórias brasileiras até a substituição de 25% de LETA. Desta forma, incorporar até 15% desse resíduo em tijolos de solo-cimento pode ser uma alternativa viável para processos que geram mais impactos ambientais, como lançamento em corpos d'água e até mesmo disposição em aterros sanitários.
- 28 March 2024
- Published by Centro Universitario de Maringa in Revista em Agronegócio e Meio Ambiente
- Vol. 17 (1) , e11418
Open AccessEfeitos da substituição parcial do solo por lodo de estação de tratamento de água em tijolos de solo-cimento
Cerca de 75% da água potável no Brasil é produzida em estações de tratamento de água (ETAs) convencionais. Resíduos são gerados neste processo, principalmente o lodo de decantadores (LETA), que segundo estudos é lançado sem tratamento em corpos d'água em 68% dessas instalações. Esta pesquisa avalia a viabilidade da adição de LETA como substituto parcial do solo em tijolos de solo-cimento no traço 1:9 (cimento: solo+LETA). O resíduo foi coletado durante a limpeza dos decantadores da ETA de Toledo-PR. Os tijolos foram produzidos com 5, 10, 15, 25 e 35% de substituição de massa de solo por LETA, além do controle (0%). As moldagens ocorreram em equipamentos industriais para reproduzir ao máximo condições reais de fabricação. Com o aumento do teor de lodo, a resistência à compressão dos tijolos foi reduzida. No entanto, as exigências normativas brasileiras foram atendidas até a adição de 15% de LETA. Houve aumento da absorção de água com o aumento do teor de lodo. No entanto, os tijolos atenderam às exigências regulatórias brasileiras até a substituição de 25% de LETA. Desta forma, incorporar até 15% desse resíduo em tijolos de solo-cimento pode ser uma alternativa viável para processos que geram mais impactos ambientais, como lançamento em corpos d'água e até mesmo disposição em aterros sanitários.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (4) , e17416
Eco-efficient concretes, optimized by Alfred’s packing model, with partial cement replacement by limestone and diabase stone powder
The clinker production process, encompassing the extraction of its constituent minerals, the combustion of fossil fuels, and the calcining of limestone rocks, contributes to approximately 5 to 7% of global CO2 emissions [1 1 V. Shobeiri, B. Bennett, T. Xie, and P. Visintin, "A comprehensive assessment of the global warming potential of geopolymer concrete," J. Clean. Prod., vol. 297, pp. 126669, 2021, http://doi.org/10.1016/j.jclepro.2021.126669. http://doi.org/10.1016/j.jclepro.2021.12... ]. In Brazil, this figure is notably lower at 2.6%, a result of high levels of additions allowed by standards [2 2 Sindicato Nacional da Indústria da Construção. Roadmap Tecnológico do Cimento Brasil, Rio de Janeiro: SNIC, 2019. ]. Therefore, several alternatives are being explored to mitigate the concrete environmental impact, including enhancing the efficiency of the cement industry, implementing carbon capture technologies, and increasing the use of additions in cement [2 2 Sindicato Nacional da Indústria da Construção. Roadmap Tecnológico do Cimento Brasil, Rio de Janeiro: SNIC, 2019. ]. For concrete producers and primary consumers of cement, a key strategy within their control is the rationalization of binder use through the adoption of more efficient mix design methods.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Revista IBRACON de Estruturas e Materiais
- Vol. 17 (4) , e17416
Open AccessEco-efficient concretes, optimized by Alfred’s packing model, with partial cement replacement by limestone and diabase stone powder
The clinker production process, encompassing the extraction of its constituent minerals, the combustion of fossil fuels, and the calcining of limestone rocks, contributes to approximately 5 to 7% of global CO2 emissions [1 1 V. Shobeiri, B. Bennett, T. Xie, and P. Visintin, "A comprehensive assessment of the global warming potential of geopolymer concrete," J. Clean. Prod., vol. 297, pp. 126669, 2021, http://doi.org/10.1016/j.jclepro.2021.126669. http://doi.org/10.1016/j.jclepro.2021.12... ]. In Brazil, this figure is notably lower at 2.6%, a result of high levels of additions allowed by standards [2 2 Sindicato Nacional da Indústria da Construção. Roadmap Tecnológico do Cimento Brasil, Rio de Janeiro: SNIC, 2019. ]. Therefore, several alternatives are being explored to mitigate the concrete environmental impact, including enhancing the efficiency of the cement industry, implementing carbon capture technologies, and increasing the use of additions in cement [2 2 Sindicato Nacional da Indústria da Construção. Roadmap Tecnológico do Cimento Brasil, Rio de Janeiro: SNIC, 2019. ]. For concrete producers and primary consumers of cement, a key strategy within their control is the rationalization of binder use through the adoption of more efficient mix design methods.
- Open Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 25 (2)
Estudo do desempenho do aço carbono AISI 1010 sob o efeito de barreira de revestimento epóxi/HDL-Zn-Al-NO2- como inibidor de corrosão, via espectroscopia de impedância eletroquímica
RESUMO Para estender a vida útil de materiais metálicos dos artefatos das linhas de distribuição e de transmissão de energia vem sendo estudado um cristal do tipo hidrotalcita que funciona como nanorreservatório, para inibidores de corrosão. Os hidróxidos duplos lamelares (HDL) são denominados compostos do tipo hidrotalcita, que são permutadores de ânions. Estruturalmente, consistem em lamelas de hidróxidos de metais misturados com cargas positivas separadas por ânions e moléculas de água. Com a exposição a meios agressivos, estes trocam íons com o ambiente agressivo e, paralelamente, liberam um agente inibidor de corrosão intercalado entre as lamelas. Nesta pesquisa foram analisados, por meio da técnica de espectroscopia de impedância eletroquímica (EIS), aço carbono 1010, aço carbono 1010 revestido com resina epóxi e aço carbono 1010 revestido com resina epóxi e adição de 5% de HDL Zn-Al de nitrito (Zn-Al- NO2-). O HDL foi caracterizado pelas técnicas de difração de raio-X (XRD) e espectroscopia de vibracional na região do infravermelho com transformada de Fourier (FTIR). Os resultados obtidos evidenciaram a viabilidade da utilização do HDL de Zn-Al- NO2- nos artefatos metalicos das linhas de distribuição e de transmissão de energia, haja vista que conferiram uma maior resistência a corrosão frente à exposição e possível penetração de íons agressivos na matriz orgânica (resina).
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 25 (2)
Open AccessEstudo do desempenho do aço carbono AISI 1010 sob o efeito de barreira de revestimento epóxi/HDL-Zn-Al-NO2- como inibidor de corrosão, via espectroscopia de impedância eletroquímica
RESUMO Para estender a vida útil de materiais metálicos dos artefatos das linhas de distribuição e de transmissão de energia vem sendo estudado um cristal do tipo hidrotalcita que funciona como nanorreservatório, para inibidores de corrosão. Os hidróxidos duplos lamelares (HDL) são denominados compostos do tipo hidrotalcita, que são permutadores de ânions. Estruturalmente, consistem em lamelas de hidróxidos de metais misturados com cargas positivas separadas por ânions e moléculas de água. Com a exposição a meios agressivos, estes trocam íons com o ambiente agressivo e, paralelamente, liberam um agente inibidor de corrosão intercalado entre as lamelas. Nesta pesquisa foram analisados, por meio da técnica de espectroscopia de impedância eletroquímica (EIS), aço carbono 1010, aço carbono 1010 revestido com resina epóxi e aço carbono 1010 revestido com resina epóxi e adição de 5% de HDL Zn-Al de nitrito (Zn-Al- NO2-). O HDL foi caracterizado pelas técnicas de difração de raio-X (XRD) e espectroscopia de vibracional na região do infravermelho com transformada de Fourier (FTIR). Os resultados obtidos evidenciaram a viabilidade da utilização do HDL de Zn-Al- NO2- nos artefatos metalicos das linhas de distribuição e de transmissão de energia, haja vista que conferiram uma maior resistência a corrosão frente à exposição e possível penetração de íons agressivos na matriz orgânica (resina).