Maxime Thiébaut
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maxime Thiébaut has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Christophe Maisondieu
IFREMER, 1625 Route de Sainte-Anne, 29280 Plouzané, France
4 shared publications Florent Guinot
France Énergies Marines, Technopôle Brest-Iroise, 525 Avenue Alexis de Rochon, 29280 Plouzané, France
3 shared publications- Guillaume Damblans
France Énergies Marines, Technopôle Brest-Iroise, 525 Avenue Alexis de Rochon, 29280 Plouzané, France
3 shared publications - Jean-François Filipot
France Énergies Marines, Technopôle Brest-Iroise, 525 Avenue Alexis de Rochon, 29280 Plouzané, France
3 shared publications Cristina Benzo
Vaisala France SAS, 6A, rue René Razel, Tech Park, CS 70001, 91400 Saclay Cedex, France
2 shared publicationsFrédéric Delbos
Vaisala France SAS, 6A rue René Razel, Tech Park, CS 70001, 91400 Saclay, France
2 shared publications
Latest Publications
- Open Access
- 17 March 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (3) , 825-838
Dual-lidar profilers for measuring atmospheric turbulence
A dual-lidar system comprising two WindCube v2.1 Doppler lidars – one oriented horizontally at a 45° angle relative to the other – was deployed to estimate atmospheric turbulence using the variance method. This approach derives second-order velocity statistics directly from line-of-sight (LOS) velocity variances, enabling the reconstruction of the three-dimensional velocity variance components without retrieving instantaneous wind vectors. Its performance is evaluated against the traditional method commonly used in the wind energy sector, which reconstructs instantaneous velocity components from single-lidar LOS measurements prior to computing turbulence statistics. Both methods are assessed at a single measurement height using a 30 d collocated dataset, with sonic anemometer measurements as reference and classification by atmospheric stability. The analysis focuses on turbulence intensity (TI), and performance is quantified using the mean relative bias error (MRBE) and relative root mean square error (RRMSE), following Det Norske Veritas (DNV) load-validation acceptance criteria (MRBE within ±5 % and RRMSE ≤ 15 %). Results show that the variance method demonstrates improved agreement with the reference measurements across nearly all wind-speed bins. For along-wind TI, MRBE values range between 0 % and −5 %, with RRMSE remaining below 15 % over the full wind-speed range, fully satisfying the DNV criteria. For cross-wind TI, the MRBE criterion is met, while the RRMSE threshold is exceeded. In contrast, the traditional method meets both DNV criteria for along-wind TI only at wind speeds above approximately 7 m s−1 and fails to satisfy either criterion for cross-wind TI across the investigated range. Overall, the results demonstrate that the variance method provides more robust and DNV-compliant TI estimates than the traditional reconstruction approach, particularly for along-wind turbulence relevant to wind turbine load validation.
- 17 March 2026
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 11 (3) , 825-838
Open AccessDual-lidar profilers for measuring atmospheric turbulence
A dual-lidar system comprising two WindCube v2.1 Doppler lidars – one oriented horizontally at a 45° angle relative to the other – was deployed to estimate atmospheric turbulence using the variance method. This approach derives second-order velocity statistics directly from line-of-sight (LOS) velocity variances, enabling the reconstruction of the three-dimensional velocity variance components without retrieving instantaneous wind vectors. Its performance is evaluated against the traditional method commonly used in the wind energy sector, which reconstructs instantaneous velocity components from single-lidar LOS measurements prior to computing turbulence statistics. Both methods are assessed at a single measurement height using a 30 d collocated dataset, with sonic anemometer measurements as reference and classification by atmospheric stability. The analysis focuses on turbulence intensity (TI), and performance is quantified using the mean relative bias error (MRBE) and relative root mean square error (RRMSE), following Det Norske Veritas (DNV) load-validation acceptance criteria (MRBE within ±5 % and RRMSE ≤ 15 %). Results show that the variance method demonstrates improved agreement with the reference measurements across nearly all wind-speed bins. For along-wind TI, MRBE values range between 0 % and −5 %, with RRMSE remaining below 15 % over the full wind-speed range, fully satisfying the DNV criteria. For cross-wind TI, the MRBE criterion is met, while the RRMSE threshold is exceeded. In contrast, the traditional method meets both DNV criteria for along-wind TI only at wind speeds above approximately 7 m s−1 and fails to satisfy either criterion for cross-wind TI across the investigated range. Overall, the results demonstrate that the variance method provides more robust and DNV-compliant TI estimates than the traditional reconstruction approach, particularly for along-wind turbulence relevant to wind turbine load validation.
- Open Access
- 4 November 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-28
Dual-lidar profilers for measuring atmospheric turbulence
A dual-lidar system, consisting of WindCube v2.1 profilers with one lidar oriented horizontally at 45° relative to the other, was deployed to estimate along- and cross-wind variances, velocity spectra, and turbulence intensity (TI) using the "variance method". This approach computes second-order statistics directly from the line-of-sight (LOS) velocity variances to infer the full three-dimensional velocity variance components. It is benchmarked against the "traditional method" commonly used in the wind energy sector, which reconstructs instantaneous velocity components from single-lidar LOS measurements before deriving second-order statistics. Both methods are evaluated at a single altitude using a 30-day collocated dataset, with reference measurements from a sonic anemometer classified by atmospheric stability conditions. Two key performance metrics are considered: the mean relative bias error (MRBE) and the relative root mean square error (RRMSE), as defined by DNV (Det Norske Veritas). Spectral analysis of the velocity components shows that, while the traditional method more closely matches the reference spectra at low frequencies, it tends to overestimate spectral energy at higher frequencies. In contrast, the variance method typically underestimates spectral energy in the along-wind component and overestimates it in the crosswind component. Furthermore, linear regression analysis reveals that the variance method captures 90–97 % of the reference variances across all stability regimes, while the traditional method tends to overestimate—especially for cross-wind variance under unstable and neutral conditions (up to 132 %). Overall, the variance method yields lower MRBE and RRMSE values for both along- and cross-wind TI. Specifically, for along-wind TI, MRBE decreases from 10.1 % to 7.5 % and RRMSE from 19.5 % to 11.7 %. For cross-wind TI, MRBE is reduced from up to 17.6 % to 12.3 %, and RRMSE from 23.4 % to 18.2 %.
- 4 November 2025
- Published by Copernicus GmbH in EGUsphere
- Vol. 2025, 1-28
Open AccessDual-lidar profilers for measuring atmospheric turbulence
A dual-lidar system, consisting of WindCube v2.1 profilers with one lidar oriented horizontally at 45° relative to the other, was deployed to estimate along- and cross-wind variances, velocity spectra, and turbulence intensity (TI) using the "variance method". This approach computes second-order statistics directly from the line-of-sight (LOS) velocity variances to infer the full three-dimensional velocity variance components. It is benchmarked against the "traditional method" commonly used in the wind energy sector, which reconstructs instantaneous velocity components from single-lidar LOS measurements before deriving second-order statistics. Both methods are evaluated at a single altitude using a 30-day collocated dataset, with reference measurements from a sonic anemometer classified by atmospheric stability conditions. Two key performance metrics are considered: the mean relative bias error (MRBE) and the relative root mean square error (RRMSE), as defined by DNV (Det Norske Veritas). Spectral analysis of the velocity components shows that, while the traditional method more closely matches the reference spectra at low frequencies, it tends to overestimate spectral energy at higher frequencies. In contrast, the variance method typically underestimates spectral energy in the along-wind component and overestimates it in the crosswind component. Furthermore, linear regression analysis reveals that the variance method captures 90–97 % of the reference variances across all stability regimes, while the traditional method tends to overestimate—especially for cross-wind variance under unstable and neutral conditions (up to 132 %). Overall, the variance method yields lower MRBE and RRMSE values for both along- and cross-wind TI. Specifically, for along-wind TI, MRBE decreases from 10.1 % to 7.5 % and RRMSE from 19.5 % to 11.7 %. For cross-wind TI, MRBE is reduced from up to 17.6 % to 12.3 %, and RRMSE from 23.4 % to 18.2 %.
- Open Access
- 8 September 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (9) , 1869-1885
Evaluating the enhanced sampling rate for turbulence measurement with a wind lidar profiler
This study evaluates the impact of an enhanced sampling rate on turbulence measurements using the Vaisala WindCube v2.1 lidar profiler. A prototype configuration, sampling 4 times faster than the commercial setup, was compared to the commercial WindCube v2.1, with reference measurements provided by a 2D sonic anemometer mounted on a measurement mast. Over the 47 d experiment, the prototype configuration showed performance similar to the commercial setup for key performance indicators (KPIs) like slope and the coefficient of determination of mean wind speed compared to reference measurements, with both configurations meeting the “best-practice” threshold. However, for mean wind speed differences, the commercial configuration met the best-practice level, while the prototype met the “minimum-acceptance” criterion. Additionally, the data availability of the prototype configuration was 0.5 % lower than that of the commercial configuration. Moreover, the increased sampling rate of the prototype lidar resulted in higher mean variance in instrumental noise compared to that of the commercial configuration. Despite this limitation, the mean noise-corrected along-wind variance measured by the prototype lidar was approximately 7 % higher than that of the commercial lidar. This effect was especially evident at higher wind speeds. Error metrics for the noise-corrected along-wind standard deviation in the prototype lidar were approximately 25 % lower than those of the commercial configuration. However, the observed improvements to the prototype configuration in measuring turbulence fell short of expectations due to inherent limitations in the measurement process within the probe, where spatial and temporal filtering effects constrain the detection of turbulence at certain scales.
- 8 September 2025
- Published by Copernicus GmbH in Wind Energy Science
- Vol. 10 (9) , 1869-1885
Open AccessEvaluating the enhanced sampling rate for turbulence measurement with a wind lidar profiler
This study evaluates the impact of an enhanced sampling rate on turbulence measurements using the Vaisala WindCube v2.1 lidar profiler. A prototype configuration, sampling 4 times faster than the commercial setup, was compared to the commercial WindCube v2.1, with reference measurements provided by a 2D sonic anemometer mounted on a measurement mast. Over the 47 d experiment, the prototype configuration showed performance similar to the commercial setup for key performance indicators (KPIs) like slope and the coefficient of determination of mean wind speed compared to reference measurements, with both configurations meeting the “best-practice” threshold. However, for mean wind speed differences, the commercial configuration met the best-practice level, while the prototype met the “minimum-acceptance” criterion. Additionally, the data availability of the prototype configuration was 0.5 % lower than that of the commercial configuration. Moreover, the increased sampling rate of the prototype lidar resulted in higher mean variance in instrumental noise compared to that of the commercial configuration. Despite this limitation, the mean noise-corrected along-wind variance measured by the prototype lidar was approximately 7 % higher than that of the commercial lidar. This effect was especially evident at higher wind speeds. Error metrics for the noise-corrected along-wind standard deviation in the prototype lidar were approximately 25 % lower than those of the commercial configuration. However, the observed improvements to the prototype configuration in measuring turbulence fell short of expectations due to inherent limitations in the measurement process within the probe, where spatial and temporal filtering effects constrain the detection of turbulence at certain scales.
- Open Access
- 12 August 2024
- Published by Copernicus GmbH in EGUsphere
- Vol. 2024, 1-23
Enhancing turbulent fluctuation measurement with tailored wind lidar profilers
This study separately investigates the impact of an enhanced sampling rate and reduced probe length on turbulent measurements using the Vaisala WindCube v2.1 lidar profiler, in comparison to the commercially configured WindCube v2.1. In the first experiment, a tailored lidar sampled four times faster than the standard setup. In the second experiment, a tailored lidar employed a 15 m probe length, compared to the commercial configuration’s 23 m. The study offers a detailed analysis of how these changes affect various aspects of wind measurement, including mean wind speed, standard deviation, velocity spectra, noise level, integral length scale, and dissipation rate. Increasing the sampling rate improves turbulence measurement without affecting mean wind speed measurement. However, a slight reduction in data availability was observed compared to the commercial configuration. Reducing the probe length results in higher standard deviation values compared to the commercial configuration, but this comes at the expense of increased noise levels, making it unclear whether the higher standard deviations are due to the energy of smaller eddies or noise. Additionally, the reduced probe length configuration exhibited a high bias in mean wind speed measurement and had a limited impact on other turbulence metrics. These findings suggest that the best improvement for turbulence measurement with the WindCube lidar profiler is achieved through an increased sampling rate.
- 12 August 2024
- Published by Copernicus GmbH in EGUsphere
- Vol. 2024, 1-23
Open AccessEnhancing turbulent fluctuation measurement with tailored wind lidar profilers
This study separately investigates the impact of an enhanced sampling rate and reduced probe length on turbulent measurements using the Vaisala WindCube v2.1 lidar profiler, in comparison to the commercially configured WindCube v2.1. In the first experiment, a tailored lidar sampled four times faster than the standard setup. In the second experiment, a tailored lidar employed a 15 m probe length, compared to the commercial configuration’s 23 m. The study offers a detailed analysis of how these changes affect various aspects of wind measurement, including mean wind speed, standard deviation, velocity spectra, noise level, integral length scale, and dissipation rate. Increasing the sampling rate improves turbulence measurement without affecting mean wind speed measurement. However, a slight reduction in data availability was observed compared to the commercial configuration. Reducing the probe length results in higher standard deviation values compared to the commercial configuration, but this comes at the expense of increased noise levels, making it unclear whether the higher standard deviations are due to the energy of smaller eddies or noise. Additionally, the reduced probe length configuration exhibited a high bias in mean wind speed measurement and had a limited impact on other turbulence metrics. These findings suggest that the best improvement for turbulence measurement with the WindCube lidar profiler is achieved through an increased sampling rate.
- Open Access
- 10 April 2024
- Published by MDPI AG in Remote Sensing
- Vol. 16 (8) , 1337
Experimental Evaluation of the Motion-Induced Effects for Turbulent Fluctuations Measurement on Floating Lidar Systems
This study examines how motion influences turbulent velocity fluctuations utilizing measurements obtained from a wind lidar profiler. Onshore tests were performed using a WindCube v2.1 lidar, which was mobile and mounted on a hexapod to simulate buoy motion. Additionally, a fixed WindCube v2.1 lidar was used as a reference during these tests. To assess the motion-induced effects on velocity fluctuations measured by floating lidar systems, the root-mean-square error (RMSE) of velocity fluctuations obtained from the fixed and mobile lidars was calculated. A comprehensive wind dataset spanning 22.5 h was analyzed, with a focus on regular motions involving single-axis rotations and combinations of rotations around multiple axes. The investigation of single-axis rotations revealed that the primary influencing factor on the results was the alignment between the tilt direction of the mobile lidar and the wind direction. The highest RMSE values occurred when the tilt of the mobile lidar leans in the wind direction, resulting in pitch motion, whereas the lowest RMSE values were observed when the tilt of the mobile lidar leans perpendicular to the wind direction, resulting in roll motion. Moreover, the addition of motion around extra axes of rotation was found to increase RMSE.
- 10 April 2024
- Published by MDPI AG in Remote Sensing
- Vol. 16 (8) , 1337
Open AccessExperimental Evaluation of the Motion-Induced Effects for Turbulent Fluctuations Measurement on Floating Lidar Systems
This study examines how motion influences turbulent velocity fluctuations utilizing measurements obtained from a wind lidar profiler. Onshore tests were performed using a WindCube v2.1 lidar, which was mobile and mounted on a hexapod to simulate buoy motion. Additionally, a fixed WindCube v2.1 lidar was used as a reference during these tests. To assess the motion-induced effects on velocity fluctuations measured by floating lidar systems, the root-mean-square error (RMSE) of velocity fluctuations obtained from the fixed and mobile lidars was calculated. A comprehensive wind dataset spanning 22.5 h was analyzed, with a focus on regular motions involving single-axis rotations and combinations of rotations around multiple axes. The investigation of single-axis rotations revealed that the primary influencing factor on the results was the alignment between the tilt direction of the mobile lidar and the wind direction. The highest RMSE values occurred when the tilt of the mobile lidar leans in the wind direction, resulting in pitch motion, whereas the lowest RMSE values were observed when the tilt of the mobile lidar leans perpendicular to the wind direction, resulting in roll motion. Moreover, the addition of motion around extra axes of rotation was found to increase RMSE.
- Open Access
- 27 September 2023
- Published by Copernicus GmbH in EGUsphere
- Vol. 2023, 1-22
Experimental evaluation of the motion-induced effects on turbulent fluctuations measurement on floating lidar systems
This study investigates the impact of motion on the line-of-sight (LOS) turbulent velocity fluctuations derived from lidar profiler measurements. Onshore tests were conducted using a WindCube v2.1 lidar, referred to as the mobile lidar, mounted on a hexapod to simulate buoy motion, with a fixed lidar used as a reference. To assess the motion-induced effects on turbulent velocity fluctuations measured by floating lidar systems, the root-mean-square error (RMSE) of LOS velocity fluctuations obtained from the fixed and mobile lidars was calculated. A comprehensive wind dataset spanning 45 hours was analyzed, with a focus on regular motions involving single-axis rotations and combinations of rotations around multiple axes. The investigation of single-axis rotations revealed that the primary influencing factor on the results was the alignment between wind direction and the axis of rotation. The highest RMSE values occurred when winds propagated perpendicular to the rotation axis, resulting in pitch motion, whereas the lowest RMSE values were observed when wind propagated along the rotation axis, leading to roll motion. Furthermore, yaw motion was found to increase the RMSE compared to scenarios without yaw motion. Moreover, the addition of motion around extra axes of rotation was found to increase RMSE. High wind speed emerged as a significant driver of RMSE, with higher velocities leading to higher RMSE values. The study also indicated that the role of wind shear in influencing RMSE of LOS velocity fluctuations requires further investigation. Additionally, the study explored the impact of motion period, revealing that motion frequencies affect the LOS velocity spectra within the expected inertial sub-range. However, the impact on RMSE was found to be limited in comparison to the amplitude, wind direction, and wind speed.
- 27 September 2023
- Published by Copernicus GmbH in EGUsphere
- Vol. 2023, 1-22
Open AccessExperimental evaluation of the motion-induced effects on turbulent fluctuations measurement on floating lidar systems
This study investigates the impact of motion on the line-of-sight (LOS) turbulent velocity fluctuations derived from lidar profiler measurements. Onshore tests were conducted using a WindCube v2.1 lidar, referred to as the mobile lidar, mounted on a hexapod to simulate buoy motion, with a fixed lidar used as a reference. To assess the motion-induced effects on turbulent velocity fluctuations measured by floating lidar systems, the root-mean-square error (RMSE) of LOS velocity fluctuations obtained from the fixed and mobile lidars was calculated. A comprehensive wind dataset spanning 45 hours was analyzed, with a focus on regular motions involving single-axis rotations and combinations of rotations around multiple axes. The investigation of single-axis rotations revealed that the primary influencing factor on the results was the alignment between wind direction and the axis of rotation. The highest RMSE values occurred when winds propagated perpendicular to the rotation axis, resulting in pitch motion, whereas the lowest RMSE values were observed when wind propagated along the rotation axis, leading to roll motion. Furthermore, yaw motion was found to increase the RMSE compared to scenarios without yaw motion. Moreover, the addition of motion around extra axes of rotation was found to increase RMSE. High wind speed emerged as a significant driver of RMSE, with higher velocities leading to higher RMSE values. The study also indicated that the role of wind shear in influencing RMSE of LOS velocity fluctuations requires further investigation. Additionally, the study explored the impact of motion period, revealing that motion frequencies affect the LOS velocity spectra within the expected inertial sub-range. However, the impact on RMSE was found to be limited in comparison to the amplitude, wind direction, and wind speed.
- 10 June 2022
- Published by Elsevier in Renewable Energy
- Vol. 195, 252-262
Investigating the flow dynamics and turbulence at a tidal-stream energy site in a highly energetic estuary
- 10 June 2022
- Published by Elsevier in Renewable Energy
- Vol. 195, 252-262
Investigating the flow dynamics and turbulence at a tidal-stream energy site in a highly energetic estuary
- Open Access
- 27 July 2020
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2178) , 20190495
Characterization of the vertical evolution of the three-dimensional turbulence for fatigue design of tidal turbines
A system of two coupled four-beam acoustic Doppler current profilers was used to collect turbulence measurements over a 36-h period at a highly energetic tidal energy site in Alderney Race. This system enables the evaluation of the six components of the Reynolds stress tensor throughout a large proportion of the water column. The present study provides mean vertical profiles of the velocity, the turbulence intensity and the integral lengthscale along the streamwise, spanwise and vertical direction of the tidal current. Based on our results and considering a tidal-stream energy convertor (TEC) aligned with the current main direction, the main elements of turbulence prone to affect the structure (material fatigue) and to alter power generation would likely be: (i) the streamwise turbulence intensity ( I x ), (ii) the shear stress, v ′ w ′ ¯ , (iii) the normal stress, u ′ 2 ¯ and (iv) the vertical integral lengthscale ( L z ). The streamwise turbulence intensity, ( I x ), was found to be higher than that estimated at other tidal energy sites across the world for similar height above bottom. Along the vertical direction, the length ( L z ) of the large-scale turbulence eddies was found to be equivalent to the rotor diameter of the TEC Sabella D10. It is considered that the turbulence metrics presented in this paper will be valuable for TECs designers, helping them optimize their designs as well as improve loading prediction through the lifetime of the machines. This article is part of the theme issue ‘New insights on tidal dynamics and tidal energy harvesting in the Alderney Race’.
- 27 July 2020
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2178) , 20190495
Open AccessCharacterization of the vertical evolution of the three-dimensional turbulence for fatigue design of tidal turbines
A system of two coupled four-beam acoustic Doppler current profilers was used to collect turbulence measurements over a 36-h period at a highly energetic tidal energy site in Alderney Race. This system enables the evaluation of the six components of the Reynolds stress tensor throughout a large proportion of the water column. The present study provides mean vertical profiles of the velocity, the turbulence intensity and the integral lengthscale along the streamwise, spanwise and vertical direction of the tidal current. Based on our results and considering a tidal-stream energy convertor (TEC) aligned with the current main direction, the main elements of turbulence prone to affect the structure (material fatigue) and to alter power generation would likely be: (i) the streamwise turbulence intensity ( I x ), (ii) the shear stress, v ′ w ′ ¯ , (iii) the normal stress, u ′ 2 ¯ and (iv) the vertical integral lengthscale ( L z ). The streamwise turbulence intensity, ( I x ), was found to be higher than that estimated at other tidal energy sites across the world for similar height above bottom. Along the vertical direction, the length ( L z ) of the large-scale turbulence eddies was found to be equivalent to the rotor diameter of the TEC Sabella D10. It is considered that the turbulence metrics presented in this paper will be valuable for TECs designers, helping them optimize their designs as well as improve loading prediction through the lifetime of the machines. This article is part of the theme issue ‘New insights on tidal dynamics and tidal energy harvesting in the Alderney Race’.
- Open Access
- 27 July 2020
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2178) , 20190496
Assessing the turbulent kinetic energy budget in an energetic tidal flow from measurements of coupled ADCPs
Two coupled four-beam acoustic Doppler current profilers were used to provide simultaneous and independent measurements of the turbulent kinetic energy (TKE) dissipation rate ε and the TKE production rate P over a 36 h long period at a highly energetic tidal energy site in the Alderney Race. The eight-beam arrangement enabled the evaluation of the six components of the Reynolds stress tensor which allows for an improved estimation of the TKE production rate. Depth-time series of ε, P and the Reynolds stresses are provided. The comparison between ε and P was performed by calculating individual ratios of ε corresponding to P . The depth-averaged ratio ε / P averaged over whole flood and ebb tide were found to be 2.2 and 2.8 respectively, indicating that TKE dissipation exceeds TKE production. It is shown that the term of diffusive transport of TKE is significant. As a result, non-local transport is important to the TKE budget and the common assumption of a local balance, i.e. a balance between production and dissipation, is not valid at the measurement site. This article is part of the theme issue ‘New insights on tidal dynamics and tidal energy harvesting in the Alderney Race’.
- 27 July 2020
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 378 (2178) , 20190496
Open AccessAssessing the turbulent kinetic energy budget in an energetic tidal flow from measurements of coupled ADCPs
Two coupled four-beam acoustic Doppler current profilers were used to provide simultaneous and independent measurements of the turbulent kinetic energy (TKE) dissipation rate ε and the TKE production rate P over a 36 h long period at a highly energetic tidal energy site in the Alderney Race. The eight-beam arrangement enabled the evaluation of the six components of the Reynolds stress tensor which allows for an improved estimation of the TKE production rate. Depth-time series of ε, P and the Reynolds stresses are provided. The comparison between ε and P was performed by calculating individual ratios of ε corresponding to P . The depth-averaged ratio ε / P averaged over whole flood and ebb tide were found to be 2.2 and 2.8 respectively, indicating that TKE dissipation exceeds TKE production. It is shown that the term of diffusive transport of TKE is significant. As a result, non-local transport is important to the TKE budget and the common assumption of a local balance, i.e. a balance between production and dissipation, is not valid at the measurement site. This article is part of the theme issue ‘New insights on tidal dynamics and tidal energy harvesting in the Alderney Race’.