Yongrae Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yongrae Kim has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Cheolwoong Park
Korea Institute of Machinery and Materials, Daejeon, Republic of Korea
6 shared publications Young Choi
5 shared publications- Young Choi
Korea Institute of Machinery and Materials, 156 Gajeongbuk-Ro, Yuseong-Gu, Daejeon 34103, Republic of Korea
3 shared publications Chansoo Park
2 shared publicationsCheolwoong Park
2 shared publicationsGyeongtae Park
2 shared publications
Latest Publications
- Open Access
- 5 March 2026
- Published by Elsevier in SSRN Electronic Journal
Experimental Study on Improving Thermal Efficiency while Maintaining Low NOx Emissions in a Hydrogen–Gasoline Dual-Fuel SI Engine
In this study, an experimental investigation was conducted on the combustion characteristics, exhaust emissions, and thermal efficiency of a spark-ignition (SI) engine equipped with hydrogen direct injection and gasoline port fuel injection under simultaneous dual-fuel operation, with a particular focus on the effect of the excess air ratio. Hydrogen and gasoline were supplied at an equal proportion based on their lower heating values, and the results were compared with single-fuel operation using hydrogen direct injection and gasoline port fuel injection, respectively.,Under gasoline-only operation, the leanest condition just before misfire was observed at an excess air ratio of 1.21, while the maximum thermal efficiency of 44.31% was achieved at an excess air ratio of 1.16. In contrast, under hydrogen-only operation at wide-open throttle (WOT), the leanest stable condition occurred at an excess air ratio of 1.79, and the highest thermal efficiency of 47.50% was obtained at the same condition. For hydrogen–gasoline dual-fuel operation with an equal energy share at WOT, stable combustion was achieved up to an excess air ratio of 1.85, and the maximum thermal efficiency reached 48.53%, exceeding those of both single-fuel cases. Furthermore, a minimum nitrogen oxides (NOx) emission level of 0.23 g/kWh was achieved, demonstrating that dual-fuel operation enables simultaneously low NOx emissions and high thermal efficiency approaching 50%.
- 5 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessExperimental Study on Improving Thermal Efficiency while Maintaining Low NOx Emissions in a Hydrogen–Gasoline Dual-Fuel SI Engine
In this study, an experimental investigation was conducted on the combustion characteristics, exhaust emissions, and thermal efficiency of a spark-ignition (SI) engine equipped with hydrogen direct injection and gasoline port fuel injection under simultaneous dual-fuel operation, with a particular focus on the effect of the excess air ratio. Hydrogen and gasoline were supplied at an equal proportion based on their lower heating values, and the results were compared with single-fuel operation using hydrogen direct injection and gasoline port fuel injection, respectively.,Under gasoline-only operation, the leanest condition just before misfire was observed at an excess air ratio of 1.21, while the maximum thermal efficiency of 44.31% was achieved at an excess air ratio of 1.16. In contrast, under hydrogen-only operation at wide-open throttle (WOT), the leanest stable condition occurred at an excess air ratio of 1.79, and the highest thermal efficiency of 47.50% was obtained at the same condition. For hydrogen–gasoline dual-fuel operation with an equal energy share at WOT, stable combustion was achieved up to an excess air ratio of 1.85, and the maximum thermal efficiency reached 48.53%, exceeding those of both single-fuel cases. Furthermore, a minimum nitrogen oxides (NOx) emission level of 0.23 g/kWh was achieved, demonstrating that dual-fuel operation enables simultaneously low NOx emissions and high thermal efficiency approaching 50%.
- Open Access
- 5 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of intake air temperature on combustion characteristics and operation range of high-pressure ammonia direct injection engine
Ammonia is emerging as a promising carbon-free fuel, particularly for internal combustion engines, due to its high hydrogen content and potential for sustainable production. However, ammonia's low flame speed and narrow flammability limit pose challenges to combustion stability and efficiency, necessitating research into strategies. This study investigates the effects of intake air temperature control on the combustion characteristics of a direct-injection ammonia-fueled spark-ignition engine. Experiments were conducted at engine speeds of 1000 rpm and 1500 rpm under varying load conditions, focusing on combustion stability, thermal efficiency, and emissions. The results indicate that increasing intake air temperature enhances combustion stability at lower engine loads by reducing ignition delay and improving fuel-air mixing. Elevated intake air temperatures resulted in increased NOx emissions due to higher peak combustion temperatures. Unburned NH3 emissions correlated with efficiency losses, increasing significantly at higher loads.
- 5 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of intake air temperature on combustion characteristics and operation range of high-pressure ammonia direct injection engine
Ammonia is emerging as a promising carbon-free fuel, particularly for internal combustion engines, due to its high hydrogen content and potential for sustainable production. However, ammonia's low flame speed and narrow flammability limit pose challenges to combustion stability and efficiency, necessitating research into strategies. This study investigates the effects of intake air temperature control on the combustion characteristics of a direct-injection ammonia-fueled spark-ignition engine. Experiments were conducted at engine speeds of 1000 rpm and 1500 rpm under varying load conditions, focusing on combustion stability, thermal efficiency, and emissions. The results indicate that increasing intake air temperature enhances combustion stability at lower engine loads by reducing ignition delay and improving fuel-air mixing. Elevated intake air temperatures resulted in increased NOx emissions due to higher peak combustion temperatures. Unburned NH3 emissions correlated with efficiency losses, increasing significantly at higher loads.
- Open Access
- 31 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (2) , 268
Effect of a Compression Ratio Increase and High-Flow-Rate Injection on the Combustion Characteristics of an Ammonia Direct Injection Spark-Ignited Engine
Despite efforts to use ammonia as a fuel, there remain problems with low combustion speeds and high unburned ammonia (NH3) emissions. Therefore, methods to compensate for slow combustion speeds and stabilize combustion have been studied. This study aims to analyze how increasing the compression ratio affects engine performance to enhance thermal efficiency and reduce unburned emissions in a high-pressure ammonia direct injection spark-ignited engine. In addition, by applying a high-flow-rate (HFR) injector, an improvement in the combustion of ammonia fuel and exhaust gas emissions is observed through changes in the air–fuel mixture formation of high-pressure directly injected ammonia fuel. Compared with the existing compression ratio, the incomplete combustion loss due to unburned NH3 increases significantly, and the thermal efficiency does not increase under an increased compression ratio. When HFR injectors are applied with an increase in the compression ratio, the net work increases by 4.7%, as incomplete combustion and energy losses of fuel are reduced by reducing the amount of unburned NH3.
- 31 January 2025
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 13 (2) , 268
Open AccessEffect of a Compression Ratio Increase and High-Flow-Rate Injection on the Combustion Characteristics of an Ammonia Direct Injection Spark-Ignited Engine
Despite efforts to use ammonia as a fuel, there remain problems with low combustion speeds and high unburned ammonia (NH3) emissions. Therefore, methods to compensate for slow combustion speeds and stabilize combustion have been studied. This study aims to analyze how increasing the compression ratio affects engine performance to enhance thermal efficiency and reduce unburned emissions in a high-pressure ammonia direct injection spark-ignited engine. In addition, by applying a high-flow-rate (HFR) injector, an improvement in the combustion of ammonia fuel and exhaust gas emissions is observed through changes in the air–fuel mixture formation of high-pressure directly injected ammonia fuel. Compared with the existing compression ratio, the incomplete combustion loss due to unburned NH3 increases significantly, and the thermal efficiency does not increase under an increased compression ratio. When HFR injectors are applied with an increase in the compression ratio, the net work increases by 4.7%, as incomplete combustion and energy losses of fuel are reduced by reducing the amount of unburned NH3.
- Open Access
Influence of Hydrogen on the Performance and Emissions Characteristics of a Spark Ignition Ammonia Direct Injection Engine
Because ammonia is easier to store and transport over long distances than hydrogen, it is a promising research direction as a potential carrier for hydrogen. However, its low ignition and combustion rates pose challenges for running conventional ignition engines solely on ammonia fuel over the entire operational range. In this study, we attempted to identify a stable engine combustion zone using a high-pressure direct injection of ammonia fuel into a 2.5 L spark ignition engine and examined the potential for extending the operational range by adding hydrogen. As it is difficult to secure combustion stability in a low-temperature atmosphere, the experiment was conducted in a sufficiently-warmed atmosphere (90 ± 2.5 °C), and the combustion, emission, and efficiency results under each operating condition were experimentally compared. At 1500 rpm, the addition of 10% hydrogen resulted in a notable 20.26% surge in the maximum torque, reaching 263.5 Nm, in contrast with the case where only ammonia fuel was used. Furthermore, combustion stability was ensured at a torque of 140 Nm by reducing the fuel and air flow rates.
Open AccessInfluence of Hydrogen on the Performance and Emissions Characteristics of a Spark Ignition Ammonia Direct Injection Engine
Because ammonia is easier to store and transport over long distances than hydrogen, it is a promising research direction as a potential carrier for hydrogen. However, its low ignition and combustion rates pose challenges for running conventional ignition engines solely on ammonia fuel over the entire operational range. In this study, we attempted to identify a stable engine combustion zone using a high-pressure direct injection of ammonia fuel into a 2.5 L spark ignition engine and examined the potential for extending the operational range by adding hydrogen. As it is difficult to secure combustion stability in a low-temperature atmosphere, the experiment was conducted in a sufficiently-warmed atmosphere (90 ± 2.5 °C), and the combustion, emission, and efficiency results under each operating condition were experimentally compared. At 1500 rpm, the addition of 10% hydrogen resulted in a notable 20.26% surge in the maximum torque, reaching 263.5 Nm, in contrast with the case where only ammonia fuel was used. Furthermore, combustion stability was ensured at a torque of 140 Nm by reducing the fuel and air flow rates.
- Open Access
- 29 March 2023
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 18
Effect of fuel injection timing on performance and emissions with a dedicated direct injector in a hydrogen engine
- 29 March 2023
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 18
Open AccessEffect of fuel injection timing on performance and emissions with a dedicated direct injector in a hydrogen engine
- 30 June 2022
- Published by The Korean Hydrogen and New Energy Society in Transactions of the Korean hydrogen and new energy society
- Vol. 33 (3) , 255-260
Performance Improvement of a Small-Sized Two Stroke Engine by Hydrogen Direct Injection
- 30 June 2022
- Published by The Korean Hydrogen and New Energy Society in Transactions of the Korean hydrogen and new energy society
- Vol. 33 (3) , 255-260
Performance Improvement of a Small-Sized Two Stroke Engine by Hydrogen Direct Injection
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Effect of Fuel Injection Timing on Performance and Emissions with Dedicated Direct Injector in a Hydrogen Engine
In the present study, using a prototype of a dedicated hydrogen direct injector (HDI), hydrogen fuel is injected directly into the cylinder, and the effect of fuel injection timing and amount of hydrogen fuel injected on engine output performance and emissions, such as nitrogen oxides and carbon dioxides, is investigated. Strategies for maximizing the engine's output performance under the condition that the after-treatment system for nitrogen oxide removal catalyst is not used were reviewed.When using the HDI, it was possible to obtain a torque improvement result of up to 35.9% even under the condition that the hydrogen supply pressure was half as low as compared to the case of using a GDI for hydrogen fuel. Under the condition of the retarded fuel injection timing, a locally rich mixture is formed to increase the emission of nitrogen oxides, and the engine oil is burned to affect the emission of carbon dioxides (CO2) and the emission of CO2 is proportional to the load.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Fuel Injection Timing on Performance and Emissions with Dedicated Direct Injector in a Hydrogen Engine
In the present study, using a prototype of a dedicated hydrogen direct injector (HDI), hydrogen fuel is injected directly into the cylinder, and the effect of fuel injection timing and amount of hydrogen fuel injected on engine output performance and emissions, such as nitrogen oxides and carbon dioxides, is investigated. Strategies for maximizing the engine's output performance under the condition that the after-treatment system for nitrogen oxide removal catalyst is not used were reviewed.When using the HDI, it was possible to obtain a torque improvement result of up to 35.9% even under the condition that the hydrogen supply pressure was half as low as compared to the case of using a GDI for hydrogen fuel. Under the condition of the retarded fuel injection timing, a locally rich mixture is formed to increase the emission of nitrogen oxides, and the engine oil is burned to affect the emission of carbon dioxides (CO2) and the emission of CO2 is proportional to the load.
- 30 June 2020
- Published by Korean Society for Atmospheric Environment in Journal of Korean Society for Atmospheric Environment
- Vol. 36 (3) , 346-359
Characteristic of Brake Wear Particles under Various Test Driving Cycles
- 30 June 2020
- Published by Korean Society for Atmospheric Environment in Journal of Korean Society for Atmospheric Environment
- Vol. 36 (3) , 346-359
Characteristic of Brake Wear Particles under Various Test Driving Cycles
- Open Access
Effect of Valve Timing and Excess Air Ratio on Torque in Hydrogen-Fueled Internal Combustion Engine for UAV
In this study, in order to convert a 2.4 L reciprocating gasoline engine into a hydrogen engine an experimental device for supplying hydrogen fuel was installed. Additionally, an injector that is capable of supplying the hydrogen fuel was installed. The basic combustion characteristics, including torque, were investigated by driving the engine with a universal engine control unit. To achieve stable combustion and maximize output, the intake and exhaust valve opening times were changed and the excess air ratio of the mixture was controlled. The changes in the torque, excess air ratio, hydrogen fuel, and intake airflow rate, were compared under low engine speed and high load (wide open throttle) operating conditions without throttling. As the intake valve opening time advanced at a certain excess air ratio, the intake air amount and torque increased. When the opening time of the exhaust valve was retarded, the intake airflow rate and torque decreased. The torque and thermal efficiency decreased when the opening time of the intake and exhaust valve advanced excessively. The change of the mixture condition’s excess air ratio did not influence the tendency of the torque variation when the exhaust valve opening time and torque increased, and when the mixture became richer and the intake valve opening time was fixed. Under a condition that was more retarded than the 332 CAD condition, the torque decreased by about 2 Nm with the 5 CAD of intake valve opening time retards. The maximum torque of 138.1 Nm was obtained at an optimized intake and the exhaust valve opening time was 327 crank angle degree (CAD) and 161 CAD, respectively, when the excess air ratio was 1.14 and the backfire was suppressed. Backfire occurred because of the temperature increase in the combustion chamber rather than because of the change in the fuel distribution under the rich mixture condition, where the other combustion control factors were constantly fixed from a three-dimensional (3D) computational fluid dynamics (CFD) code simulation.
Open AccessEffect of Valve Timing and Excess Air Ratio on Torque in Hydrogen-Fueled Internal Combustion Engine for UAV
In this study, in order to convert a 2.4 L reciprocating gasoline engine into a hydrogen engine an experimental device for supplying hydrogen fuel was installed. Additionally, an injector that is capable of supplying the hydrogen fuel was installed. The basic combustion characteristics, including torque, were investigated by driving the engine with a universal engine control unit. To achieve stable combustion and maximize output, the intake and exhaust valve opening times were changed and the excess air ratio of the mixture was controlled. The changes in the torque, excess air ratio, hydrogen fuel, and intake airflow rate, were compared under low engine speed and high load (wide open throttle) operating conditions without throttling. As the intake valve opening time advanced at a certain excess air ratio, the intake air amount and torque increased. When the opening time of the exhaust valve was retarded, the intake airflow rate and torque decreased. The torque and thermal efficiency decreased when the opening time of the intake and exhaust valve advanced excessively. The change of the mixture condition’s excess air ratio did not influence the tendency of the torque variation when the exhaust valve opening time and torque increased, and when the mixture became richer and the intake valve opening time was fixed. Under a condition that was more retarded than the 332 CAD condition, the torque decreased by about 2 Nm with the 5 CAD of intake valve opening time retards. The maximum torque of 138.1 Nm was obtained at an optimized intake and the exhaust valve opening time was 327 crank angle degree (CAD) and 161 CAD, respectively, when the excess air ratio was 1.14 and the backfire was suppressed. Backfire occurred because of the temperature increase in the combustion chamber rather than because of the change in the fuel distribution under the rich mixture condition, where the other combustion control factors were constantly fixed from a three-dimensional (3D) computational fluid dynamics (CFD) code simulation.