Bryan J. Harder

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flame tube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275 to 400 psig (1896–2758 kPa) and an air flowrate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3000 °F (1649 °C), 900 °F (482 °C) cooling air may be supplied to the backside of components or test articles. The flame tube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the test section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless-steel 304 housing. The use of a copper liner minimizes welds and, with active cooling, is expected to provide better durability over traditional hardware using stainless-steel or Inconel with a ceramic liner. The test section has two opposing 9.5 in × 3.125 in (241 mm × 80 mm) removable windows that can accommodate articles up to 3.5 in (89 mm) tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Oxygen produced through in‐situ resource utilization (ISRU) is critical to maintaining a permanent human presence on the lunar surface. Molten regolith electrolysis and carbothermal reduction are two promising ISRU techniques for generating oxygen directly from lunar regolith, which is primarily a mixture of oxide minerals; however, both processes require operating temperatures of 1600°C to melt lunar regolith and dissociate the molten oxides. These conditions limit the use of many oxide refractory materials, such as Al ₂ O ₃ and MgO, due to rapid degradation resulting from reactions between the refractory materials and molten lunar regolith. Yttria‐stabilized zirconia (YSZ) is shown here to be a promising refractory oxide to provide containment of molten regolith while demonstrating limited reactivity. This work focuses on corrosion studies of YSZ powders and dense YSZ crucibles in contact with molten lunar maria and highlands regolith simulants at 1600°C. The interactions between YSZ and molten regolith were characterized using scanning electron microscopy/energy dispersive spectroscopy, X‐ray diffraction, and electron backscatter diffraction. A FactSage thermochemical model was created for comparison with the experimental results. These combined analyses suggest that lunar maria regolith will degrade the YSZ faster than the lunar highlands regolith due to the lower viscosity of the maria regolith. The feasibility of long‐term molten regolith containment with YSZ is discussed based on the YSZ powder and crucible results.

This work outlines the development of a new natural gas/oxygen (NG/O₂) fueled combustion rig located at the NASA Glenn Research Center for high-temperature environmental durability studies of advanced materials and components at atmospheric pressure. The NG/O₂ burner rig can simulate the high-temperature, high-heat flux, and high-velocity thermal environments encountered in gas turbine engines. It also provides the capability to study environmental effects such as water vapor and other foreign contaminants relevant to these applications. The rig is anticipated to bridge the gap between other laboratory methods such as furnaces, jet-fueled burner rigs, high-heat flux lasers, and more expensive engine rig testing. The NG/O₂ rig is expected to have maximum sample temperature capabilities over 3,000°F (1,649°C) and result in higher water vapor content compared to our Mach 0.3 to Mach 1.0 jet-A burner rigs which is important for characterizing current and next-generation environmental barrier coatings. This paper will provide an overview of the development of the NG/O₂ burner rig, initial characterization, and current research and development efforts on environmental barrier coated ceramic matrix composites.

Ceramic matrix composites (CMCs) and environmental barrier coatings (EBCs) are key technologies that can enable improvements in the thermal and propulsive efficiency of gas turbine engines. However, CMCs and EBCs are susceptible to various life limiting damage modes associated with the engine operating environment such as oxidation, recession, thermomechanical stress/strain, corrosion, foreign object damage (FOD), and solid particle erosion (SPE). Despite its importance, there is a limited understanding of the SPE behavior of CMCs and EBCs in the literature. This paper reviews the status of SPE research for CMCs and EBCs and provides a perspective towards future research.

Solid particle erosion (SPE) is a common phenomenon observed in gas turbine engines. Particles entrained in the gas flow impact engine hardware, resulting in micro-scale damage that leads to deleterious effects such as material removal. For protective coatings, damage due to SPE is a key concern, since it can negatively affect the durability of the coating and subsequently the life of the underlying component. In this work, the high-temperature SPE behavior of two state-of-the-art environmental barrier coatings (EBCs) deposited via air plasma spray (APS) is investigated using alumina erodent to understand the effect of particle kinetic energy, impingement angle, and temperature. The SPE behavior of the EBCs is also compared to APS and electron beam–physical vapor deposition (EB-PVD) thermal barrier coatings (TBCs) to elucidate similarities and differences in the erosion response. The EBCs were more susceptible to SPE than the EB-PVD TBC but had greater SPE resistance compared to the APS TBC. Coating microstructure and porosity were shown to have a strong influence on the observed behavior.

A FIB/STEM interfacial study was performed on a TBC/Ti₂AlC MAX phase system, oxidized in an aggressive burner rig test (Mach 0.3 at 1300 °C for 500 h). The 7YSZ TBC, α-Al₂O₃ TGO, and MAXthal 211^TM Ti₂AlC base were variously characterized by TEM/STEM, EDS, SADP, and HRTEM. The YSZ was a mix of “clean” featureless and “faulted” high contrast grains. The latter exhibited ferro-elastic domains of high Y content tetragonal t″ variants. No martensite was observed. The TGO was essentially a duplex α-Al₂O₃ structure of inner columnar plus outer equiaxed grains. It maintained a perfectly intact, clean interface with the Ti₂AlC substrate. The Ti₂AlC substrate exhibited no interfacial Al-depletion zone but, rather, numerous faults along the basal plane of the hexagonal structure. These are believed to offer a means of depleting Al by forming crystallographic, low-Al planar defects, proposed as Ti_2.5AlC_1.5. These characterizations support and augment prior optical, SEM, and XRD findings that demonstrated remarkable durability for the YSZ/Ti₂AlC MAX phase system in aggressive burner tests.

The process scale-up of fully oxide-based environmental barrier coatings (EBCs) on sintered SiC and chemical vapor infiltration (CVI) SiC/SiC ceramic matrix composite (CMC) sub-components was investigated using various slurry manufacturing processes (dip, spray, spin–dip). The performance of EBC-coated sub-components (SiC heating element, SiC/SiC ceramic matrix mini-composite, SiC airfoil, SiC/SiC CMC airfoil) was evaluated in steam oxidation and combustion rigs. Steam oxidation was conducted at 1427 °C in 90 vol.% H₂O (g) + 10 vol.% O₂ (g) with a 1 h hold at 1427 °C per cycle (1 h hot and 20 min cooling). For high-pressure combustion rig testing, the EBC surface temperature ranged between 1354 °C and 1538 °C with the temperature gradient through CMC + EBC ranging between 100 °C and 150 °C. Dip and spin–dip are non-line-of-sight processes, whereas spray is a line-of-sight process. The three processes, collectively, demonstrated the capability to manufacture slurry EBCs on sub-components with various shapes and sizes. There was no discernable disparity in the EBC steam oxidation performance between the coupons and sub-components in this study and coupons in a previous study. The dependence of steam oxidation rates on the substrate chemistry reported previously was confirmed. The steam oxidation rate of EBC-coated sintered SiC, compared with EBC-coated CVI CMC, was ~2 times and ~1.5 times higher after 100 h and 500 h, respectively, due to the boron sintering aid in sintered SiC. An EBC-coated CMC airfoil after 150 15-h-long cycles in a high-pressure combustion rig test showed only limited EBC spallation along the leading edge and more substantial spallation along the trailing edge, demonstrating the feasibility of an oxide-based bond coat to meet the extreme temperature requirements of next-generation EBCs.

The current standard application method for thermal barrier coatings (TBCs) on turbine blades for jet engines is electron-beam physical vapor deposition (EB-PVD) due to its high strain tolerance and low thermal conductivity. An emerging deposition method, plasma-spray physical vapor deposition (PS-PVD), presents an opportunity for a tailorable microstructure, and non-line-of-sight deposition that is faster and less expensive. To compare the lifetime behavior of both PS-PVD and EB-PVD coatings, samples subjected to 300 and 600 thermal cycles were measured during a 1 h thermal cycle to determine the strains, which were converted to stress, in the thermally grown oxide (TGO) layer of the TBCs using synchrotron X-ray diffraction (XRD). Room temperature XRD measurements indicated among samples that PS-PVD coatings experienced greater variation in in-plane room temperature strain in the TGO after cycling than the EB-PVD coatings. In-situ XRD measurements indicated similar high-temperature strain and no spallation after 600 thermal cycles for both coatings. Microscopy imaging after cycling showed greater rumpling in PS-PVD coatings that led to different failure modes between the two coatings’ TGO layers. The tailorability of PS-PVD coatings allows for adjustments in the processing parameters to improve their overall performance after aging and bridge the differences between the two deposition methods.