Wolfgang Schulz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wolfgang Schulz has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Goran Erik Hallum
RWTH Aachen University
3 shared publications - Christoph Schöler
RWTH Aachen University
2 shared publications Dorian Kürschner
RWTH Aachen University
2 shared publications- Heinz Paul Huber
Munich University of Applied Sciences
2 shared publications - Ulrich Halm
RWTH Aachen University
2 shared publications - Andrij Pich
Chair of Functional and Interactive Polymers, Institute of Technical and Macromolecular Chemistry, RWTH Aachen University, Worringerweg 2, 52074 Aachen, Germany
1 shared publication
Latest Publications
- 5 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (26) , 43017-43034
Indium tin oxide ultrafast laser lift-off ablation mechanisms and damage minimization
We draw comparisons between the ablation and damage mechanisms that occur for both film and substrate irradiation using atomic force microscopy, scanning electron microscopy, and pump-probe reflectometry. For substrate irradiation, energy absorbed at the film-substrate interface creates a confined energy situation, resulting in a photomechanical lift-off. A partial ablation at the edges of the ablated zone formed the burr and was reduced in height by minimizing the area subject to the partial ablation threshold fluence. Substrate damage is understood to arise from free electron diffusion from indium tin oxide and subsequent laser heating. We establish a process window for substrate irradiation in a single-pulse ablation regime between approximately two to three times the ablation threshold of 0.18 J/cm2, validating the process window seen in literature and provide a crucial understanding for the ablation mechanisms of transparent conductive films.
- 5 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (26) , 43017-43034
Indium tin oxide ultrafast laser lift-off ablation mechanisms and damage minimization
We draw comparisons between the ablation and damage mechanisms that occur for both film and substrate irradiation using atomic force microscopy, scanning electron microscopy, and pump-probe reflectometry. For substrate irradiation, energy absorbed at the film-substrate interface creates a confined energy situation, resulting in a photomechanical lift-off. A partial ablation at the edges of the ablated zone formed the burr and was reduced in height by minimizing the area subject to the partial ablation threshold fluence. Substrate damage is understood to arise from free electron diffusion from indium tin oxide and subsequent laser heating. We establish a process window for substrate irradiation in a single-pulse ablation regime between approximately two to three times the ablation threshold of 0.18 J/cm2, validating the process window seen in literature and provide a crucial understanding for the ablation mechanisms of transparent conductive films.
- 7 April 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 209
Static and transient optical properties of thin film indium tin oxide during laser excitation
- 7 April 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 209
Static and transient optical properties of thin film indium tin oxide during laser excitation
- Open Access
- 1 September 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (19) , 30062-30076
Time-resolved ultrafast laser ablation dynamics of thin film indium tin oxide
The interaction of ultrashort laser pulses above the ablation threshold of thin-film indium tin oxide (ITO) is examined with pump-probe microscopy. We are able to observe photomechanical spallation at delay times of hundreds of picoseconds, which plays a stronger role near the ablation threshold of 0.17 J/cm2. A phase explosion may also be observed at tens of picoseconds, playing a stronger role for increasing peak fluences. As one exceeds the material removal efficiency maximum near 0.6 J/cm2, a second spallation is observable in the center of the irradiated spot at a delay time of one nanosecond and corresponds to a crater depth of 50 nanometers. No discernable ridge formation has been observed. We recommend an industrial processing window of at least two pulses per position with a peak fluence between 0.6–1.0 J/cm2.
- 1 September 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (19) , 30062-30076
Open AccessTime-resolved ultrafast laser ablation dynamics of thin film indium tin oxide
The interaction of ultrashort laser pulses above the ablation threshold of thin-film indium tin oxide (ITO) is examined with pump-probe microscopy. We are able to observe photomechanical spallation at delay times of hundreds of picoseconds, which plays a stronger role near the ablation threshold of 0.17 J/cm2. A phase explosion may also be observed at tens of picoseconds, playing a stronger role for increasing peak fluences. As one exceeds the material removal efficiency maximum near 0.6 J/cm2, a second spallation is observable in the center of the irradiated spot at a delay time of one nanosecond and corresponds to a crater depth of 50 nanometers. No discernable ridge formation has been observed. We recommend an industrial processing window of at least two pulses per position with a peak fluence between 0.6–1.0 J/cm2.
- 1 July 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 67, 170-176
In situ X-ray tomography investigations on laser welding of copper with 515 and 1030 nm laser beam sources
- 1 July 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 67, 170-176
In situ X-ray tomography investigations on laser welding of copper with 515 and 1030 nm laser beam sources
- Open Access
- 1 April 2021
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 168
Simulation of melt film dynamics in laser fusion cutting using a boundary layer approximation
- 1 April 2021
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 168
Open AccessSimulation of melt film dynamics in laser fusion cutting using a boundary layer approximation
- 8 March 2021
- Published by Springer Nature
- p. 277-285
Optimization of Beam Shapes for Laser Fusion Cutting by 3D Simulation of Melt Flow
- 8 March 2021
- Published by Springer Nature
- p. 277-285
Optimization of Beam Shapes for Laser Fusion Cutting by 3D Simulation of Melt Flow
- 8 March 2021
- Published by Springer Nature
- p. 29-39
Numerical Investigation of Keyhole Depth Formation in Micro Welding of Copper with 1030 nm and 515 nm Laser Radiation
- 8 March 2021
- Published by Springer Nature
- p. 29-39
Numerical Investigation of Keyhole Depth Formation in Micro Welding of Copper with 1030 nm and 515 nm Laser Radiation
- Open Access
- 1 January 2016
- Published by Wiley in Journal of Healthcare Engineering
- Vol. 2016, 1-8
Modelling pH-Optimized Degradation of Microgel-Functionalized Polyesters
We establish a novel mathematical model to describe and analyze pH levels in the vicinity of poly(N-vinylcaprolactam-co-acetoacetoxyethyl methacrylate-co-N-vinylimidazole) (VCL/AAEM/VIm) microgel-functionalized polymers during biodegradation. Biodegradable polymers, especially aliphatic polyesters (polylactide/polyglycolide/polycaprolactone homo- and copolymers), have a large range of medical applications including delivery systems, scaffolds, or stents for the treatment of cardiovascular diseases. Most of those applications are limited by the inherent drop of pH level during the degradation process. The combination of polymers with VCL/AAEM/VIm-microgels, which aims at stabilizing pH levels, is innovative and requires new mathematical models for the prediction of pH level evaluation. The mathematical model consists of a diffusion-reaction PDE system for the degradation including reaction rate equations and diffusion of acidic degradation products into the vicinity. A system of algebraic equations is coupled to the degradation model in order to describe the buffering action of the microgel. The model is validated against the experimental pH-monitored biodegradation of microgel-functionalized polymer foils and is available for the design of microgel-functionalized polymer components.
- 1 January 2016
- Published by Wiley in Journal of Healthcare Engineering
- Vol. 2016, 1-8
Open AccessModelling pH-Optimized Degradation of Microgel-Functionalized Polyesters
We establish a novel mathematical model to describe and analyze pH levels in the vicinity of poly(N-vinylcaprolactam-co-acetoacetoxyethyl methacrylate-co-N-vinylimidazole) (VCL/AAEM/VIm) microgel-functionalized polymers during biodegradation. Biodegradable polymers, especially aliphatic polyesters (polylactide/polyglycolide/polycaprolactone homo- and copolymers), have a large range of medical applications including delivery systems, scaffolds, or stents for the treatment of cardiovascular diseases. Most of those applications are limited by the inherent drop of pH level during the degradation process. The combination of polymers with VCL/AAEM/VIm-microgels, which aims at stabilizing pH levels, is innovative and requires new mathematical models for the prediction of pH level evaluation. The mathematical model consists of a diffusion-reaction PDE system for the degradation including reaction rate equations and diffusion of acidic degradation products into the vicinity. A system of algebraic equations is coupled to the degradation model in order to describe the buffering action of the microgel. The model is validated against the experimental pH-monitored biodegradation of microgel-functionalized polymer foils and is available for the design of microgel-functionalized polymer components.