Zhonglong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhonglong Li has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jiangning Pei
School of Architecture and Civil Engineering, Harbin University of Science and Technology, Harbin 150080, China
2 shared publications - Shengbao Wang
School of Architecture and Civil Engineering, Harbin University of Science and Technology, Harbin 150080, China
2 shared publications - Songlin Qin
School of Architecture and Civil Engineering, Harbin University of Science and Technology, Harbin 150080, China
2 shared publications - Baowei Lv
Heilongjiang Highway Development Center, Harbin 150001, China
1 shared publication - Fulin Su
School of Architecture and Civil Engineering, Harbin University of Science and Technology, Harbin 150080, China
1 shared publication - Guangpeng Xu
Longjian Science and Industry (Heilongjiang) Company Limited, Harbin 150009, China
1 shared publication
Latest Publications
- Open Access
Using Iterative Correction to Improve the Accuracy of the Blind-Hole Welding Residual Stress Test
An iterative correction method for the stress release coefficient, leveraging numerical simulation, has been innovatively developed to address the significant error issues associated with the blind-hole method in high-stress residual stress testing of steel structures. This method effectively reduces measurement error in high residual stress regions through a discriminant iteration process. The finite element analysis technology was employed to accurately simulate the blind-hole method’s test process, and additionally, Python was utilized for customizing the secondary development of ABAQUS software, thereby automating and optimizing the method. When compared with simulation and experimental data from the welding process, the efficiency, accuracy, and reliability of the correction method have been verified. The proposed method eliminates the need for tedious calibration experiments inherent in traditional methods, significantly enhancing the test’s automation level and convergence speed, and ensuring measurement accuracy, which provides an innovative solution for the accurate evaluation of residual stress in steel structures.
Open AccessUsing Iterative Correction to Improve the Accuracy of the Blind-Hole Welding Residual Stress Test
An iterative correction method for the stress release coefficient, leveraging numerical simulation, has been innovatively developed to address the significant error issues associated with the blind-hole method in high-stress residual stress testing of steel structures. This method effectively reduces measurement error in high residual stress regions through a discriminant iteration process. The finite element analysis technology was employed to accurately simulate the blind-hole method’s test process, and additionally, Python was utilized for customizing the secondary development of ABAQUS software, thereby automating and optimizing the method. When compared with simulation and experimental data from the welding process, the efficiency, accuracy, and reliability of the correction method have been verified. The proposed method eliminates the need for tedious calibration experiments inherent in traditional methods, significantly enhancing the test’s automation level and convergence speed, and ensuring measurement accuracy, which provides an innovative solution for the accurate evaluation of residual stress in steel structures.
- Open Access
Experimental and Numerical Simulation Study on Residual Stress of Single-Sided Full-Penetration Welded Rib-to-Deck Joint of Orthotropic Steel Bridge Deck
Orthotropic steel bridge decks (OSDs) play a key role in long-span bridges, and full-penetration welding technology is crucial to improve their structural performance. This study proposes an innovative single-sided full-penetration welding rib-to-deck (RTD) joint technology. The accuracy of the numerical simulation in predicting the temperature field and stress field was verified by the combination of an experimental and numerical simulation, and the welding residual stress (WRS) of single-sided full-penetration welded RTD joints was analyzed. In addition, the effects of different welding parameters and RTD joint geometry on the WRS are discussed. The results show that the experimental results are consistent with the simulation results, indicating that the single-sided full-penetration welding technology without a groove is feasible. The WRS shows a peak tensile stress near the weld, which gradually decreases and transforms into compressive stress as the distance increases. In addition, the WRS of the roof surface and the U-rib surface increases slightly with the increase in the roof thickness and the welding speed. The research results are of great significance to optimize the welding process, improve the fatigue performance, and prolong the service life of steel bridge decks, providing a new technical method for bridge engineering.
Open AccessExperimental and Numerical Simulation Study on Residual Stress of Single-Sided Full-Penetration Welded Rib-to-Deck Joint of Orthotropic Steel Bridge Deck
Orthotropic steel bridge decks (OSDs) play a key role in long-span bridges, and full-penetration welding technology is crucial to improve their structural performance. This study proposes an innovative single-sided full-penetration welding rib-to-deck (RTD) joint technology. The accuracy of the numerical simulation in predicting the temperature field and stress field was verified by the combination of an experimental and numerical simulation, and the welding residual stress (WRS) of single-sided full-penetration welded RTD joints was analyzed. In addition, the effects of different welding parameters and RTD joint geometry on the WRS are discussed. The results show that the experimental results are consistent with the simulation results, indicating that the single-sided full-penetration welding technology without a groove is feasible. The WRS shows a peak tensile stress near the weld, which gradually decreases and transforms into compressive stress as the distance increases. In addition, the WRS of the roof surface and the U-rib surface increases slightly with the increase in the roof thickness and the welding speed. The research results are of great significance to optimize the welding process, improve the fatigue performance, and prolong the service life of steel bridge decks, providing a new technical method for bridge engineering.
- Open Access
- 24 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 13786
Study on the Reliability Evaluation Method and Diagnosis of Bridges in Cold Regions Based on the Theory of MCS and Bayesian Networks
The safety assessment of bridges in cold areas under the special environmental effects of extremely low temperatures, frequent freezing and thawing, and chloride ion erosion from snow removal with deicing salt, presents challenges that requiring solving. Thus, this paper proposes a new method of safety assessment based on a combination of Monte Carlo simulation (MCS) and Bayesian theory that achieves the reliability evaluation and reverse diagnosis of the overall safety performance of reinforced concrete bridges in cold areas. Additionally, the new method accomplishes the intelligent grading of various safety performance aspects of the bridge, which provides substantial references for the maintenance and reinforcement of in-service bridges.
- 24 October 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 13786
Open AccessStudy on the Reliability Evaluation Method and Diagnosis of Bridges in Cold Regions Based on the Theory of MCS and Bayesian Networks
The safety assessment of bridges in cold areas under the special environmental effects of extremely low temperatures, frequent freezing and thawing, and chloride ion erosion from snow removal with deicing salt, presents challenges that requiring solving. Thus, this paper proposes a new method of safety assessment based on a combination of Monte Carlo simulation (MCS) and Bayesian theory that achieves the reliability evaluation and reverse diagnosis of the overall safety performance of reinforced concrete bridges in cold areas. Additionally, the new method accomplishes the intelligent grading of various safety performance aspects of the bridge, which provides substantial references for the maintenance and reinforcement of in-service bridges.
- Open Access
- 30 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (15) , 5258
Numerical Investigation of the Dynamic Performance and Riding Comfort of a Straddle-Type Monorail Subjected to Moving Trains
The driving comfort of a straddle-type monorail, while considering the influence of the bridge structure, was studied on the basis of multibody dynamics and the finite element method. In this study, the coupled vehicle-bridge model was established through SIMPACK and ANSYS; the 3D model of the bridge was established in ANSYS, and the vehicle model with 35 degrees of freedom (DOFs) was established in SIMPACK. The influence of the vehicle speed, pier height, track irregularity, and vehicle load on riding comfort was studied. Overall, straddle-type monorails had a good running stability, and the lateral comfort of the vehicle was better than the vertical comfort, due to symmetrical horizontal wheels. As the vehicle speed increased, the acceleration of the bridge and vehicle increased accordingly. Track irregularity had a substantial influence on riding comfort. Three types of track irregularity were simulated, and this factor should be strictly controlled to be smoother than the Chinese national A-level road roughness. The bridge pier height had a notable influence on the lateral riding comfort. In addition, this study attempted to improve riding comfort from the perspective of increasing the bridge stiffness, which could be achieved by increasing the cross-beam thickness or the track beam height.
- 30 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (15) , 5258
Open AccessNumerical Investigation of the Dynamic Performance and Riding Comfort of a Straddle-Type Monorail Subjected to Moving Trains
The driving comfort of a straddle-type monorail, while considering the influence of the bridge structure, was studied on the basis of multibody dynamics and the finite element method. In this study, the coupled vehicle-bridge model was established through SIMPACK and ANSYS; the 3D model of the bridge was established in ANSYS, and the vehicle model with 35 degrees of freedom (DOFs) was established in SIMPACK. The influence of the vehicle speed, pier height, track irregularity, and vehicle load on riding comfort was studied. Overall, straddle-type monorails had a good running stability, and the lateral comfort of the vehicle was better than the vertical comfort, due to symmetrical horizontal wheels. As the vehicle speed increased, the acceleration of the bridge and vehicle increased accordingly. Track irregularity had a substantial influence on riding comfort. Three types of track irregularity were simulated, and this factor should be strictly controlled to be smoother than the Chinese national A-level road roughness. The bridge pier height had a notable influence on the lateral riding comfort. In addition, this study attempted to improve riding comfort from the perspective of increasing the bridge stiffness, which could be achieved by increasing the cross-beam thickness or the track beam height.