LGLina Gao

Lina Gao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lina Gao has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Strength and Toughness Mechanisms of Layered Ti 3 AlC 2 Reinforced TiAl 3 ‐Based Composites

    by Lina Gao, Shufeng Li, Xin Zhang, Bo Li

    Revealing the unique strength and toughness mechanisms of Ti 3 AlC 2 in the TiAl 3 matrix is a challenge of great scientific and practical significance. Ti 3 AlC 2 /TiAl 3 composites were fabricated by in situ reaction which using TiC, TiH 2 , and Al powder as the raw materials. Then, the compressive properties and fracture toughness of the composites were tested. The as‐prepared Ti 3 AlC 2 /TiAl 3 composite with 30% mass fraction of the reinforcement exhibits excellent comprehensive mechanical performance. Its compressive strength, compressive strain and K IC are 1647 ± 21 MPa, 7.1 ± 0.1% and 3.83 ± 0.05 MPa·m 1/2 , respectively, which are 193%, 203%, and 143% higher than those of the pure TiAl 3 matrix. It is demonstrated that the layered Ti 3 AlC 2 reinforcements enhance the strength of Ti 3 AlC 2 /TiAl 3 composites through microdeformations such as interlayer tearing, kinking, shearing, and tensile fracture; Simultaneously, they increase the toughness of the Ti 3 AlC 2 /TiAl 3 composites by generating new interfaces via interlayer sliding and the formation of cleavage planes or cleavage steps.

  • High-temperature mechanical behavior of Ti 3 AlC 2 reinforced TiAl 3 based composites

    by Lina Gao, Shufeng Li, Xin Zhang, Bo Li

    Ti 3 AlC 2 /TiAl 3 composite has shown great potential for the lightweight high-temperature structural materials. Studying its high-temperature mechanical properties and revealing its high-temperature strengthening mechanisms is a highly challenging task. In this work, Ti 3 AlC 2 enhanced TiAl 3 matrix composites with different reinforcements mass fractions were successfully prepared at 1300°C by powder metallurgy route. Then, the high-temperature compressive properties of the composites were tested, and the macroscopic and microscopic structural morphologies of the compressed specimens were characterized. The results indicate that the high-temperature compressive properties of Ti 3 AlC 2 /TiAl 3 composites exhibit negative temperature sensitivity and positive strain rate sensitivity. At 900°C, the compressive peak stress of the 10-40Ti 3 AlC 2 /TiAl 3 composites is 16.6-41.3% higher than that of TiAl 3 matrix, indicating a significant strengthening effect. The pinning effect of Ti 3 AlC 2 particles on dislocations and grain boundaries, as well as the good interfacial bonding between Ti 3 AlC 2 particles and the TiAl 3 matrix, are the main reasons for improving the high-temperature compressive strength of Ti 3 AlC 2 /TiAl 3 composites.

  • In-situ reaction mechanism of Ti3AlC2/TiAl3 composite prepared by powder metallurgy

    by Lina Gao, Shufeng Li, Dongxu Hui, Shaodi Wang, Shaolong Li, Xin Zhang, Bo Li


  • Open Access

    Process Optimization of SiC-Reinforced Aluminum Matrix Composites Prepared Using Laser Powder Bed Fusion and the Effect of Particle Morphology on Performance

    by Xinghua Ji, Shufeng Li, Huiying Liu, Xin Li, Xin Zhang, Lei Liu, Shaolong Li, Lina Gao, Shaodi Wang, Biao Chen, et al.

    Process parameters and powder spreading quality are important factors for aluminum matrix composites (AMCs) prepared using laser powder bed fusion (LPBF). In this study, a Box–Behnken Design (BBD) was used to optimize the process parameters, and near-spherical β-SiC was selected to improve the quality of powder spreading. The rationality of parameter optimization was verified by testing the density of samples prepared using different laser power levels. Al4C3 diffraction peaks were found in XRD patterns, which indicated that interface reactions occurred to form good interface bonding between the Al matrix and the SiC particles. The tensile strength and plasticity of LPBF α-SiC/AlSi10Mg were lower than that of LPBF AlSi10Mg, which was mainly due to the poor fluidity of the powder mixtures and powder spreading quality. For LPBF β-SiC/AlSi10Mg, the tensile strength increased and elongation decreased slightly compared to LPBF α-SiC/AlSi10Mg. The data in this study were compared with the data in other studies. In this study, LPBF AlSi10Mg and LPBF β-SiC/AlSi10Mg not only showed the inherent high strength of their LPBF parts, but also had relatively high plasticity. Matching between strength and plasticity was mainly dependent on the scanning strategy. Most studies use uni-directional or bi-directional scanning strategies with a certain rotation angle between layers. A chessboard scanning strategy was used in this study to form a coarse remelted connected skeleton inside the material and significantly improve plasticity. This study lays a theoretical and experimental foundation for the controllable preparation of SiC-reinforced AMCs using LPBF.


  • Open Access

    Loss-free tensile ductility of dual-structure titanium composites via an interdiffusion and self-organization strategy

    by Lei Liu, Shufeng Li, Deng Pan, Dongxu Hui, Xin Zhang, Bo Li, Tianshou Liang, Pengpeng Shi, Abdollah Bahador, Junko Umeda, et al.

    The deformation-coordination ability between ductile metal and brittle dispersive ceramic particles is poor, which means that an improvement in strength will inevitably sacrifice ductility in dispersion-strengthened metallic materials. Here, we present an inspired strategy for developing dual-structure-based titanium matrix composites (TMCs) that achieve 12.0% elongation comparable to the matrix Ti6Al4V alloys and enhanced strength compared to homostructure composites. The proposed dual-structure comprises a primary structure, namely, a TiB whisker-rich region engendered fine grain Ti6Al4V matrix with a three-dimensional micropellet architecture (3D-MPA), and an overall structure consisting of evenly distributed 3D-MPA “reinforcements” and a TiBw-lean titanium matrix. The dual structure presents a spatially heterogeneous grain distribution with 5.8 μm fine grains and 42.3 μm coarse grains, which exhibits excellent hetero-deformation-induced (HDI) hardening and achieves a 5.8% ductility. Interestingly, the 3D-MPA “reinforcements” show 11.1% isotropic deformability and 66% dislocation storage, which endows the TMCs with good strength and loss-free ductility. Our enlightening method uses an interdiffusion and self-organization strategy based on powder metallurgy to enable metal matrix composites with the heterostructure of the matrix and the configuration of reinforcement to address the strength-ductility trade-off dilemma.


  • Open Access

    Microstructure, properties and fracture mechanism of MAX phase Ti3AlC2 ceramics with Si doping via Ti–Al–C system by powder metallurgy

    by Lina Gao, Shufeng Li, Ting Han, Lei Liu, Deng Pan, Xin Zhang, Yakun Zhang, Yiming Zhang, Yuyang He, Wenge Chen, et al.


  • Preparation and performance of MAX phase Ti3AlC2 by in-situ reaction of Ti-Al-C system

    by Lina Gao, Ting Han, Zhaolong Guo, Xin Zhang, Deng Pan, Shengyin Zhou, Wenge Chen, Shufeng Li