Sepehr Sadighi
Research Subjects
Sepehr Sadighi has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Seyed Reza Seif Mohaddecy
Catalysis Development Technologies Division, Research Institute of Petroleum Industry (RIPI)
3 shared publicationsM. Shirvani
Cement Research Center, Iran University of Science and Technology, Tehran, Iran
2 shared publications- Mehdi Rashidzadeh
Research Institute of Petroleum Industry (RIPI)
2 shared publications A. Abbasi
Research Institute of the Petroleum Industry (RIPI), Catalysis and Nanotechnology Research Division, Tehran, Iran
1 shared publicationA. Fazlollahi
Research Institute of the Petroleum Industry (RIPI), Catalysis and Nanotechnology Research Division, Tehran, Iran
1 shared publicationAkbar Irandoukht
Catalysis Technologies Development Division, Research Institute of Petroleum Industry, Tehran, Iran
1 shared publication
Latest Publications
- 5 March 2024
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 43 (11) , 1166-1181
Sub-dew point claus process for reducing hydrogen sulfide emission from sulfur recovery units
- 5 March 2024
- Published by Taylor & Francis in Petroleum Science and Technology
- Vol. 43 (11) , 1166-1181
Sub-dew point claus process for reducing hydrogen sulfide emission from sulfur recovery units
- Open Access
- 25 May 2020
- Published by BCREC Publishing Group in Bulletin of Chemical Reaction Engineering & Catalysis
- Vol. 15 (2) , 465-475
Modeling, Evaluating and Scaling up a Commercial Multilayer Claus Converter Based on Bench Scale Experiments
Industrial scale reactors work adiabatically and measuring their performance in an isothermal bench scale reactor is faced with uncertainties. In this research, based on kinetic models previously developed for alumina and titania commercial Claus catalysts, a multilayer bench scale model is constructed, and it is applied to simulate the behavior of an industrial scale Claus converter. It is shown that performing the bench scale isothermal experiments at the temperature of 307 ºC can reliably exhibit the activity of catalytic layers of an industrial Claus converter operating at the weighted average bed temperature (WABT) of 289 ºC. Additionally, an adiabatic model is developed for a target industrial scale Claus reactor, and it is confirmed that this model can accurately predict the temperature, and molar percentages of H2S and CS2. Based on simulation results, 20% of excess amount of Claus catalysts should be loaded to compensate their deactivation during the process cycle life. Copyright © 2020 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
- 25 May 2020
- Published by BCREC Publishing Group in Bulletin of Chemical Reaction Engineering & Catalysis
- Vol. 15 (2) , 465-475
Open AccessModeling, Evaluating and Scaling up a Commercial Multilayer Claus Converter Based on Bench Scale Experiments
Industrial scale reactors work adiabatically and measuring their performance in an isothermal bench scale reactor is faced with uncertainties. In this research, based on kinetic models previously developed for alumina and titania commercial Claus catalysts, a multilayer bench scale model is constructed, and it is applied to simulate the behavior of an industrial scale Claus converter. It is shown that performing the bench scale isothermal experiments at the temperature of 307 ºC can reliably exhibit the activity of catalytic layers of an industrial Claus converter operating at the weighted average bed temperature (WABT) of 289 ºC. Additionally, an adiabatic model is developed for a target industrial scale Claus reactor, and it is confirmed that this model can accurately predict the temperature, and molar percentages of H2S and CS2. Based on simulation results, 20% of excess amount of Claus catalysts should be loaded to compensate their deactivation during the process cycle life. Copyright © 2020 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
- 1 March 2020
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 60 (3) , 321-328
Kinetic-based Models for Alumina and Titania Claus Catalysts Based on Experimental Data
Catalytic section of Claus process is significant for increasing the efficiency of sulfur recovery, and decreasing the amount of H2S emission to the environment. In this research, experiments at different gas hourly space velocities (GHSVs) and temperatures were carried out in a bench scale plant in the presence of both alumina (Al2O3) and titania (TiO2) commercial Claus catalysts. The feed composition and operating conditions were selected within the range of a target industrial scale plant. Thereafter, an isotherm model was constructed for the bench scale reactor, and its kinetic parameters were estimated using the obtained data. Results showed that H2S and CS2 conversions over Al2O3 and TiO2 Claus catalysts could be predicted with the average absolute deviation (AAD) of 9.86 and 30.03%, and 15.31 and 4.22%, respectively.
- 1 March 2020
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 60 (3) , 321-328
Kinetic-based Models for Alumina and Titania Claus Catalysts Based on Experimental Data
Catalytic section of Claus process is significant for increasing the efficiency of sulfur recovery, and decreasing the amount of H2S emission to the environment. In this research, experiments at different gas hourly space velocities (GHSVs) and temperatures were carried out in a bench scale plant in the presence of both alumina (Al2O3) and titania (TiO2) commercial Claus catalysts. The feed composition and operating conditions were selected within the range of a target industrial scale plant. Thereafter, an isotherm model was constructed for the bench scale reactor, and its kinetic parameters were estimated using the obtained data. Results showed that H2S and CS2 conversions over Al2O3 and TiO2 Claus catalysts could be predicted with the average absolute deviation (AAD) of 9.86 and 30.03%, and 15.31 and 4.22%, respectively.
- Open Access
- 1 January 2020
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 85 (10) , 1345-1356
Investigation the effects of Al-grafting and calcination temperature on acidity and physicochemical properties of silica SBA-15
In this study, the effect of calcination temperature and Si/Al mole ratio on acidity and physicochemical properties of silica SBA-15 were investigated. Silica SBA-15 samples were calcined at 350, 450 and 550?C, and then post-synthesis, the Al-grafting method was applied to incorporate aluminum species into their framework with Si/Al mole ratio of 10 and 30. Characterizations using small angle XRD and N2 adsorption?desorption techniques indicated that the hexagonal mesoporous structure was retained after performing Al-grafting even at the high aluminum loading. Moreover, FTIR results implied that the aluminum species were incorporated into the SBA-15 framework. NH3-TPD results showed that by decreasing Si/Al mole ratio at all calcination temperatures, the number of weak acid sites increased in comparison to those of the pure SBA-15 samples. Additionally, the maximum total acidity of synthesized samples was observed at the calcination temperature of 450?C with Si/Al mole ratio of 30.
- 1 January 2020
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 85 (10) , 1345-1356
Open AccessInvestigation the effects of Al-grafting and calcination temperature on acidity and physicochemical properties of silica SBA-15
In this study, the effect of calcination temperature and Si/Al mole ratio on acidity and physicochemical properties of silica SBA-15 were investigated. Silica SBA-15 samples were calcined at 350, 450 and 550?C, and then post-synthesis, the Al-grafting method was applied to incorporate aluminum species into their framework with Si/Al mole ratio of 10 and 30. Characterizations using small angle XRD and N2 adsorption?desorption techniques indicated that the hexagonal mesoporous structure was retained after performing Al-grafting even at the high aluminum loading. Moreover, FTIR results implied that the aluminum species were incorporated into the SBA-15 framework. NH3-TPD results showed that by decreasing Si/Al mole ratio at all calcination temperatures, the number of weak acid sites increased in comparison to those of the pure SBA-15 samples. Additionally, the maximum total acidity of synthesized samples was observed at the calcination temperature of 450?C with Si/Al mole ratio of 30.
- Open Access
- 26 January 2018
- Published by International Journal of Technology in International Journal of Technology
- Vol. 9 (1) , 99-109
Modeling and Optimizing a Vacuum Gas Oil Hydrocracking Plant using an Artificial Neural Network
In this research, based on actual data gathered from an industrial scale vacuum gas oil (VGO) hydrocracker and artificial neural network (ANN) method, a model is proposed to simulate yields of products including light gases, liquefied petroleum gas (LPG), light naphtha, heavy naphtha, kerosene, diesel and unconverted oil (off-test). The input layer of the ANN model consists of the catalyst, feed and recycle flow rates, and bed temperatures, while the output neurons are yields of those products. The results showed that the AAD% (average absolute deviation) of the developed ANN model for training, testing, and validating data are 0.445%, 1.131% and 0.755%, respectively. Then, by considering all operational constraints, the results confirmed that the decision variables (i.e., recycle rate and bed temperatures) generated by the optimization approach can enhance the gross profit of the hydrocracking process to more than $0.81 million annually, which is significant for the economy of the target refinery.
- 26 January 2018
- Published by International Journal of Technology in International Journal of Technology
- Vol. 9 (1) , 99-109
Open AccessModeling and Optimizing a Vacuum Gas Oil Hydrocracking Plant using an Artificial Neural Network
In this research, based on actual data gathered from an industrial scale vacuum gas oil (VGO) hydrocracker and artificial neural network (ANN) method, a model is proposed to simulate yields of products including light gases, liquefied petroleum gas (LPG), light naphtha, heavy naphtha, kerosene, diesel and unconverted oil (off-test). The input layer of the ANN model consists of the catalyst, feed and recycle flow rates, and bed temperatures, while the output neurons are yields of those products. The results showed that the AAD% (average absolute deviation) of the developed ANN model for training, testing, and validating data are 0.445%, 1.131% and 0.755%, respectively. Then, by considering all operational constraints, the results confirmed that the decision variables (i.e., recycle rate and bed temperatures) generated by the optimization approach can enhance the gross profit of the hydrocracking process to more than $0.81 million annually, which is significant for the economy of the target refinery.
- 26 July 2017
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 16 (1)
Modeling and Evaluating Zeolite and Amorphous Based Catalysts in Vacuum Gas Oil Hydrocracking Process
Hydrocracking is a significant process in a refinery which is commonly used for converting heavy fractions such as vacuum gas oil (VGO) to the valuable products such as naphtha and diesel. In this research, VGO hydrocracking process was studied in a pilot scale plant in the presence of a zeolite and two amorphous based commercial catalysts called RK-NiY, RK-MNi and KF-101, respectively. In order to study the effect of support on the yield of the process, a discrete 4-lump kinetic model, including feed (vacuum gas oil and unconverted materials), distillate (diesel and kerosene), naphtha and gas was proposed for each catalyst. At first, each network had six reaction paths and twelve kinetic coefficients, and then by using the model reduction methodology, only four main routes for RK-MNi and RK-NiY, and three ones for KF-101 were designated. Results showed that the absolute average deviation (AAD%) of reduced models decreased from 5.11 %, 10.1 % and 21.8 % to 4.54 %, 8.9 % and 19.67 % for RK-MNi, KF-101 and RK-NiY, respectively. Moreover, it was confirmed that amorphous and zeolite catalysts could be selected for producing middle distillate and naphtha products, respectively.
- 26 July 2017
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 16 (1)
Modeling and Evaluating Zeolite and Amorphous Based Catalysts in Vacuum Gas Oil Hydrocracking Process
Hydrocracking is a significant process in a refinery which is commonly used for converting heavy fractions such as vacuum gas oil (VGO) to the valuable products such as naphtha and diesel. In this research, VGO hydrocracking process was studied in a pilot scale plant in the presence of a zeolite and two amorphous based commercial catalysts called RK-NiY, RK-MNi and KF-101, respectively. In order to study the effect of support on the yield of the process, a discrete 4-lump kinetic model, including feed (vacuum gas oil and unconverted materials), distillate (diesel and kerosene), naphtha and gas was proposed for each catalyst. At first, each network had six reaction paths and twelve kinetic coefficients, and then by using the model reduction methodology, only four main routes for RK-MNi and RK-NiY, and three ones for KF-101 were designated. Results showed that the absolute average deviation (AAD%) of reduced models decreased from 5.11 %, 10.1 % and 21.8 % to 4.54 %, 8.9 % and 19.67 % for RK-MNi, KF-101 and RK-NiY, respectively. Moreover, it was confirmed that amorphous and zeolite catalysts could be selected for producing middle distillate and naphtha products, respectively.
- 23 March 2017
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 15 (4)
Deactivation of Chlorinated Pt/Al 2 O 3 Isomerization Catalyst Using Water Containing Feed
Light naphtha isomerization is a significant process in a crude oil refinery which is responsible for upgrading low-octane light naphtha to the high-octane and low-aromatic content gasoline. In this work, deactivation of an industrial chlorinated Pt/Al 2 O 3 isomerization catalyst was studied in a laboratory scale plant. Experiments were carried out under temperatures in the range of 120–180 °C, liquid hourly space velocities (LHSV) of 0.7–2 h −1 and hydrogen to hydrocarbon molar ratios (H 2 /Oil) of 0.7–1.5. Moreover, the total water content of the combined feed, i. e. n-hexane and hydrogen, was 70 ppmwt. During 75 h time on stream (TOS), 42 data sets were collected and applied for training, testing and validating a hybrid-artificial neural network model (hybrid-ANN or HANN) to estimate the activity of the catalyst. Results showed that the activity decreased to 0.56 at the end of the operation mostly due to water poisoning. Furthermore, using the estimated activity, HANN could simulate the conversion and selectivity of the isomerization process with the absolute average deviations (AAD%) of 0.97 % and 0.0766 % and the mean squared errors (MSE) of 0.311 and 0.0156, respectively.
- 23 March 2017
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 15 (4)
Deactivation of Chlorinated Pt/Al 2 O 3 Isomerization Catalyst Using Water Containing Feed
Light naphtha isomerization is a significant process in a crude oil refinery which is responsible for upgrading low-octane light naphtha to the high-octane and low-aromatic content gasoline. In this work, deactivation of an industrial chlorinated Pt/Al 2 O 3 isomerization catalyst was studied in a laboratory scale plant. Experiments were carried out under temperatures in the range of 120–180 °C, liquid hourly space velocities (LHSV) of 0.7–2 h −1 and hydrogen to hydrocarbon molar ratios (H 2 /Oil) of 0.7–1.5. Moreover, the total water content of the combined feed, i. e. n-hexane and hydrogen, was 70 ppmwt. During 75 h time on stream (TOS), 42 data sets were collected and applied for training, testing and validating a hybrid-artificial neural network model (hybrid-ANN or HANN) to estimate the activity of the catalyst. Results showed that the activity decreased to 0.56 at the end of the operation mostly due to water poisoning. Furthermore, using the estimated activity, HANN could simulate the conversion and selectivity of the isomerization process with the absolute average deviations (AAD%) of 0.97 % and 0.0766 % and the mean squared errors (MSE) of 0.311 and 0.0156, respectively.
- Open Access
- 18 October 2016
- Published by BCREC Publishing Group in Bulletin of Chemical Reaction Engineering & Catalysis
- Vol. 12 (1) , 49-54
Preparation of Biofuel from Palm Oil Catalyzed by Ammonium Molybdate in Homogeneous Phase
Producing transportation fuels from bio sources was of prime importance due to the strict environmental legislations for producing clean fuels from conventional oil resources. However, the economical impacts of the biofuel production should be considered. In this study, the production of bio-naphtha and biodiesel from palm oil using homogeneous catalyst, i.e. an aqueous phase of ammonium molybdate, was studied. This catalyst was prepared by dissolving sodium molybdate in de-ionized water with hydrochloric acid, and then neutralizing the mixture with ammonium hydroxide. The solution was dried at 90 °C for 24 h to obtain ammonium molybdate. Then, characterization of the catalyst was done by informative techniques, such as XRD and FT-IR. The results showed that the main phase of the synthesized catalyst was molybdate ammonium hydrates (4MoO3.2NH3.H2O), and also bands of Mo–O, Mo–O–Mo, N–H and surface hydroxyl groups were observed in the sample. Moreover, activity test confirms that the bio-naphtha produced from the proposed method has a few aromatic components, and its sulfur content was negligible. Moreover, ash, nitrogen, sulfur and carbon residue were not detected in the produced biodiesel, and its Cetane index was 66.3. Therefore, it was a suitable fuel for diesel engines vehicles.
- 18 October 2016
- Published by BCREC Publishing Group in Bulletin of Chemical Reaction Engineering & Catalysis
- Vol. 12 (1) , 49-54
Open AccessPreparation of Biofuel from Palm Oil Catalyzed by Ammonium Molybdate in Homogeneous Phase
Producing transportation fuels from bio sources was of prime importance due to the strict environmental legislations for producing clean fuels from conventional oil resources. However, the economical impacts of the biofuel production should be considered. In this study, the production of bio-naphtha and biodiesel from palm oil using homogeneous catalyst, i.e. an aqueous phase of ammonium molybdate, was studied. This catalyst was prepared by dissolving sodium molybdate in de-ionized water with hydrochloric acid, and then neutralizing the mixture with ammonium hydroxide. The solution was dried at 90 °C for 24 h to obtain ammonium molybdate. Then, characterization of the catalyst was done by informative techniques, such as XRD and FT-IR. The results showed that the main phase of the synthesized catalyst was molybdate ammonium hydrates (4MoO3.2NH3.H2O), and also bands of Mo–O, Mo–O–Mo, N–H and surface hydroxyl groups were observed in the sample. Moreover, activity test confirms that the bio-naphtha produced from the proposed method has a few aromatic components, and its sulfur content was negligible. Moreover, ash, nitrogen, sulfur and carbon residue were not detected in the produced biodiesel, and its Cetane index was 66.3. Therefore, it was a suitable fuel for diesel engines vehicles.
- 10 June 2016
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 33 (9) , 2538-2546
A two-dimensional discrete lumped model for a trickle-bed vacuum gas oil hydrocracking reactor
- 10 June 2016
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 33 (9) , 2538-2546
A two-dimensional discrete lumped model for a trickle-bed vacuum gas oil hydrocracking reactor
- 26 November 2013
- Published by Wiley in Energy Technology
- Vol. 1 (12) , 743-750
Studying Catalyst Activity in an Isomerization Plant to Upgrade the Octane Number of Gasoline by Using a Hybrid Artificial‐Neural‐Network Model
In this study, a hybrid model is presented for estimating the activity of a commercial Pt/zeolite catalyst in an industrial‐scale light naphtha isomerization unit. This model is also capable of predicting the research octane number (RON) and Reid vapor pressure (RVP) of gasoline, the flow rate of product, and the temperature profile of the reactor. In the proposed model, the decay function of heterogeneous catalysts is combined with a recurrent‐layer artificial neural network. To identify the activity of catalyst, a set of 52 data points during 272 days were gathered from the target isomerization plant. From these data, 31 points were selected for training (60 %), 11 data points for testing (20 %) and the remained ones for validating the developed hybrid network (20 %). Results show that the presented hybrid model can acceptably estimate the activity of the catalyst during its life in consideration of all process variables. Moreover, it is confirmed that for unseen (validating) data, the proposed model is capable of predicting RON, RVP, flow rate of gasoline, and the temperatures of the middle and end sections of the isomerization reactor with an average absolute deviations (AAD %) of 0.0769 %, 0.118 %, 0.6945 %, 0.042 %, and 0.1137 %, respectively.
- 26 November 2013
- Published by Wiley in Energy Technology
- Vol. 1 (12) , 743-750
Studying Catalyst Activity in an Isomerization Plant to Upgrade the Octane Number of Gasoline by Using a Hybrid Artificial‐Neural‐Network Model
In this study, a hybrid model is presented for estimating the activity of a commercial Pt/zeolite catalyst in an industrial‐scale light naphtha isomerization unit. This model is also capable of predicting the research octane number (RON) and Reid vapor pressure (RVP) of gasoline, the flow rate of product, and the temperature profile of the reactor. In the proposed model, the decay function of heterogeneous catalysts is combined with a recurrent‐layer artificial neural network. To identify the activity of catalyst, a set of 52 data points during 272 days were gathered from the target isomerization plant. From these data, 31 points were selected for training (60 %), 11 data points for testing (20 %) and the remained ones for validating the developed hybrid network (20 %). Results show that the presented hybrid model can acceptably estimate the activity of the catalyst during its life in consideration of all process variables. Moreover, it is confirmed that for unseen (validating) data, the proposed model is capable of predicting RON, RVP, flow rate of gasoline, and the temperatures of the middle and end sections of the isomerization reactor with an average absolute deviations (AAD %) of 0.0769 %, 0.118 %, 0.6945 %, 0.042 %, and 0.1137 %, respectively.