YYYuanquan Yang

Yuanquan Yang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yuanquan Yang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tri-Magnesium Phosphate as a Candidate Biocompatible Retarder for Magnesium Potassium Phosphate Cement: Setting Behavior, Mechanical Properties, and Microstructure

    by Yuanquan Yang, Xiaoyu Ying, Hao Huang, Yunpeng Cui

    Magnesium potassium phosphate cement (MKPC) is a promising bone repair material but suffers from excessively rapid setting time (typically within minutes) that limits clinical application. This study systematically investigates trimagnesium phosphate (TMP) as a candidate retarding additive for MKPC. TMP was used to partially replace dead-burned magnesium oxide at replacement levels of 0%, 10%, and 15% by mass. The effects of TMP content, water-to-cement ratio (0.17–0.23), and magnesium-to-phosphate molar ratio (4–10) on setting time, fluidity, hydration kinetics, compressive strength, and microstructure were comprehensively evaluated. Results show that TMP effectively extends the setting time from 9–13 min (without TMP) to 10–19 min, providing a working window that may be suitable for biomedical applications requiring extended handling time. Notably, 10% TMP incorporation enhances early compressive strength, with 1-day strength reaching 35.2 MPa compared to 28.5 MPa for control samples. Hydration heat analysis reveals TMP moderates the acid-base reaction kinetics through its slower dissolution rate compared to MgO. Microstructural characterization shows TMP promotes the formation of denser K-struvite crystals with refined microstructure. The optimal TMP dosage of 10% achieves a balanced performance, extending setting time while improving early strength and microstructural densification. These findings establish TMP as an effective retarder for developing MKPC-based materials with potential for biomedical applications, pending further biological validation.

  • Open Access

    SiO2-Induced Performance Deterioration in Magnesium Phosphate Cement: Chemical Consumption and Physical Deactivation of Reactive Magnesia

    by Yuanquan Yang, Xiaoyu Ying, Jiamin Han, Chengwen Luan

    This study investigates the dual mechanisms by which SiO2 deteriorates magnesium phosphate cement (MPC) performance. MgO-SiO2 clinkers were prepared using lightly calcined magnesia (MgO) with SiO2 additions ranging from 1% to 9%, followed by calcination at temperatures between 1100 °C and 1500 °C. Through XRD–Rietveld refinement, workability, compressive strength, and hydration heat analyses, the damaging effects of SiO2 were systematically evaluated. Results reveal that SiO2 degrades MPC through two concurrent mechanisms: chemical consumption and physical deactivation of reactive MgO. Chemically, SiO2 reacts with MgO during calcination to form inert forsterite (Mg2SiO4), irreversibly reducing reactive MgO content. Physically, SiO2 and its reaction products lower the crystallinity and reactivity of remaining MgO while diluting reactive components. A calcination temperature of 1200 °C was optimal, yielding the highest compressive strength (3 d strength > 30 MPa). Increasing SiO2 dosage monotonically reduced strength; at 1200 °C, 9% SiO2 reduced 3 d strength by ~40% compared to 1%. Hydration heat analysis showed that both heat flow rate and cumulative heat release increased with SiO2 content due to enhanced heterogeneous nucleation from Mg2SiO4. Critically, this increased heat output did not translate into higher strength, indicating that microstructural quality—not reaction extent—governs mechanical performance. Rietveld quantification confirmed that Mg2SiO4 formation increased linearly with SiO2 dosage and temperature (reaching 72.24% at 1500 °C with 9% SiO2), providing the material basis for dual damage. This work offers mechanistic insights and experimental support for utilizing low-grade magnesite and optimizing MPC performance.

  • Open Access

    Corrosion Resistance of Concrete Reinforced by Zinc Phosphate Pretreated Steel Fiber in the Presence of Chloride Ions

    by Xingke Zhao, Runqing Liu, Wenhan Qi, Yuanquan Yang

    This paper aims to provide new insight into a method to improve the chloride ion corrosion resistance of steel fiber reinforced concrete. The steel fiber was pretreated by zinc phosphate before the preparation of the fiber reinforced concrete. Interfacial bond strength, micro-hardness and micro-morphology properties were respectively analyzed in the steel fiber reinforced concrete before and after the chloride corrosion cycle test. The results show that the chloride ion corrosion resistance of the steel fiber was enhanced by zinc phosphate treatment. Compared to plain steel fiber reinforced concrete under chloride ion corrosion, the interfacial bond strength of the concrete prepared by steel fiber with phosphating treatment increased by 15.4%. The thickness of the interface layer between the pretreated steel fiber and cement matrix was reduced by 50%. The micro-hardness of the weakest point in the interface area increased by 54.2%. The micro-morphology of the interface area was almost unchanged before and after the corrosion. The steel fiber reinforced concrete modified by zinc phosphate can not only maintain the stability of the microstructure when corroded by chloride ion but also presents good bearing capacity.


  • Open Access

    Study on Preparation and thermal reflective properties of energy saving pigments with selective solar reflection

    by Yunlong Li, Yuanquan Yang

    Currently, the color of common reflective insulation coating is mainly white, but the white color coating is monotonous and its resistance is poor, moreover, the reflective performance tends to drop after pollution. In addition, color coating has the advantages of anti-dirty and beautiful appearance, so study on colored paint is of great significance. Based on the principle of three-tone color, the effect of thermal reflective pigments on the near-infrared reflectance of color reflective heat-insulating coatings was studied by blending three kinds of color reflective heat-insulating coatings of orange, green and purple with composite inorganic heat-reflective pigments as raw materials. The results show that the thermal insulation effect of heat-reflective pigments is significantly improved, and the near-infrared reflectance of green pigments can be increased by about 25%. The thermal reflection thermal insulation coating of the green system is 2.78 times higher than that of the same color common thermal insulating coating.


  • Open Access

    Study on Base Resin of Fire-proof and Anticorrosive Steel Structure Coatings

    by Jun Shi, Yuan Quan Yang

    Study on the effect of waterborne epoxy resin on coating properties. The experimental results show that the basic and mechanical properties of the paint film will be enhanced with the appropriate increase of curing agent. When the amount of waterborne epoxy resin: curing agent = 1:1.25, the film performance is the best. When the curing agent content continues to increase, it will affect the performance of the coating; The amount of distilled water in waterborne epoxy resin also affects the performance of the paint film. When the amount of waterborne epoxy resin: distilled water consumption = 1:1.25, the film performance is the best, When the amount of distilled water continues to increase, the viscosity, impact strength and hardness of the paint film begin to decrease.