Junhyeok Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junhyeok Choi has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Sungjun Kim
School of Electronics and Electrical Engineering, Dongguk University, Seoul, 04620, South Korea
3 shared publications - Hojeong Ryu
Division of Electronics and Electrical Engineering, Dongguk University, Seoul 04620, Korea
1 shared publication
Latest Publications
- Open Access
Voltage Amplitude-Controlled Synaptic Plasticity from Complementary Resistive Switching in Alloying HfOx with AlOx-Based RRAM
In this work, the synaptic plasticity from complementary resistive switching in a HfAlOx-based resistive memory device was emulated by a direct current (DC) voltage sweep, current sweep, and pulse transient. The alloyed HfAlOx dielectric was confirmed by X-ray photoelectron spectroscopy analysis. The negative differential resistance observed before the forming and set processes can be used for interface resistive switching with a low current level. Complementary resistive switching is obtained after the forming process at a negative bias. This unique resistive switching is also suitable for synaptic device applications in which the reset process occurs after an additional set process. The current sweep mode provides more clear information on the complementary resistive switching. Multiple current states are achieved by controlling the amplitude of the set and reset voltages under DC sweep mode. The potentiation and depression characteristics are mimicked by varying the pulse voltage amplitude for synaptic device application in a neuromorphic system. Finally, we demonstrate spike-timing-dependent plasticity by tuning the timing differences between pre-spikes and post-spikes.
Open AccessVoltage Amplitude-Controlled Synaptic Plasticity from Complementary Resistive Switching in Alloying HfOx with AlOx-Based RRAM
In this work, the synaptic plasticity from complementary resistive switching in a HfAlOx-based resistive memory device was emulated by a direct current (DC) voltage sweep, current sweep, and pulse transient. The alloyed HfAlOx dielectric was confirmed by X-ray photoelectron spectroscopy analysis. The negative differential resistance observed before the forming and set processes can be used for interface resistive switching with a low current level. Complementary resistive switching is obtained after the forming process at a negative bias. This unique resistive switching is also suitable for synaptic device applications in which the reset process occurs after an additional set process. The current sweep mode provides more clear information on the complementary resistive switching. Multiple current states are achieved by controlling the amplitude of the set and reset voltages under DC sweep mode. The potentiation and depression characteristics are mimicked by varying the pulse voltage amplitude for synaptic device application in a neuromorphic system. Finally, we demonstrate spike-timing-dependent plasticity by tuning the timing differences between pre-spikes and post-spikes.
- Open Access
- 29 September 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (10) , 905
Improved Stability and Controllability in ZrN-Based Resistive Memory Device by Inserting TiO2 Layer
In this work, the enhanced resistive switching of ZrN-based resistive switching memory is demonstrated by embedding TiO2 layer between Ag top electrode and ZrN switching layer. The Ag/ZrN/n-Si device exhibits unstable resistive switching as a result of the uncontrollable Ag migration. Both unipolar and bipolar resistive switching with high RESET current were observed. Negative-SET behavior in the Ag/ZrN/n-Si device makes set-stuck, causing permanent resistive switching failure. On the other hand, the analogue switching in the Ag/TiO2/ZrN/n-Si device, which could be adopted for the multi-bit data storage applications, is obtained. The gradual switching in Ag/TiO2/ZrN/n-Si device is achieved, possibly due to the suppressed Ag diffusion caused by TiO2 inserting layer. The current–voltage (I–V) switching characteristics of Ag/ZrN/n-Si and Ag/TiO2/ZrN/n-Si devices can be well verified by pulse transient. Finally, we established that the Ag/TiO2/ZrN/n-Si device is suitable for neuromorphic application through a comparison study of conductance update. This paper paves the way for neuromorphic application in nitride-based memristor devices.
- 29 September 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (10) , 905
Open AccessImproved Stability and Controllability in ZrN-Based Resistive Memory Device by Inserting TiO2 Layer
In this work, the enhanced resistive switching of ZrN-based resistive switching memory is demonstrated by embedding TiO2 layer between Ag top electrode and ZrN switching layer. The Ag/ZrN/n-Si device exhibits unstable resistive switching as a result of the uncontrollable Ag migration. Both unipolar and bipolar resistive switching with high RESET current were observed. Negative-SET behavior in the Ag/ZrN/n-Si device makes set-stuck, causing permanent resistive switching failure. On the other hand, the analogue switching in the Ag/TiO2/ZrN/n-Si device, which could be adopted for the multi-bit data storage applications, is obtained. The gradual switching in Ag/TiO2/ZrN/n-Si device is achieved, possibly due to the suppressed Ag diffusion caused by TiO2 inserting layer. The current–voltage (I–V) switching characteristics of Ag/ZrN/n-Si and Ag/TiO2/ZrN/n-Si devices can be well verified by pulse transient. Finally, we established that the Ag/TiO2/ZrN/n-Si device is suitable for neuromorphic application through a comparison study of conductance update. This paper paves the way for neuromorphic application in nitride-based memristor devices.
- Open Access
Nonlinear Characteristics of Complementary Resistive Switching in HfAlOx-Based Memristor for High-Density Cross-Point Array Structure
In this work, we present the nonlinear current–voltage (I–V) characteristics of a complementary resistive switching (CRS)-like curve from a HfAlOx-based memristor, used to implement a high-density cross-point array. A Pt/HfAlOx/TiN device has lower on-current and larger selectivity compared to Pt/HfO2/TiN or Pt/Al2O3/TiN devices. It has been shown that the on-current and first reset peak current after the forming process are crucial in obtaining a CRS-like curve. We demonstrate transient CRS-like characteristics with high nonlinearity under pulse response for practical applications. Finally, after finding the optimal conditions for high selectivity, the calculated read margin proves that a Pt/HfAlOx/TiN device with a CRS-like curve is most suitable for use in a high-density cross-point array. Our results suggest that the built-in selector properties in a Pt/HfAlOx/TiN single layer device offer considerable potential in terms of the simplicity of the processes involved in the cross-point structure.
Open AccessNonlinear Characteristics of Complementary Resistive Switching in HfAlOx-Based Memristor for High-Density Cross-Point Array Structure
In this work, we present the nonlinear current–voltage (I–V) characteristics of a complementary resistive switching (CRS)-like curve from a HfAlOx-based memristor, used to implement a high-density cross-point array. A Pt/HfAlOx/TiN device has lower on-current and larger selectivity compared to Pt/HfO2/TiN or Pt/Al2O3/TiN devices. It has been shown that the on-current and first reset peak current after the forming process are crucial in obtaining a CRS-like curve. We demonstrate transient CRS-like characteristics with high nonlinearity under pulse response for practical applications. Finally, after finding the optimal conditions for high selectivity, the calculated read margin proves that a Pt/HfAlOx/TiN device with a CRS-like curve is most suitable for use in a high-density cross-point array. Our results suggest that the built-in selector properties in a Pt/HfAlOx/TiN single layer device offer considerable potential in terms of the simplicity of the processes involved in the cross-point structure.