Viktor M. Fliagin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Viktor M. Fliagin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Natalia Anatolievna Ivanova
Photonics and Microfluidics Laboratory, X-BIO Institute, University of Tyumen, 6 Volodarskogo, 625003 Tyumen, Russia
4 shared publications D.S. Klyuev
Univ Tyumen, Inst X BIO, Photon & Microfluid Lab, 6 Volodarskogo St, Tyumen 625003, Russia
2 shared publications- Konstantin Sergeevich Kolegov
Mathematical Modeling Lab, Astrakhan Tatishchev State University, Astrakhan City, Russia
2 shared publications - Mohammed A. Al-Muzaiqer
Photonics and Microfluidics Laboratory, X-BIO Institute, University of Tyumen, Tyumen 625003, Russia
2 shared publications M.A. Al-Muzaiqer
1 shared publicationN.A. Ivanova
1 shared publication
Latest Publications
- 6 December 2025
- Published by Springer Nature in The European Physical Journal E
- Vol. 48 (10-12) , 72
Shape of liquid meniscus in open cells of varying geometry: a combined study via simulation and experiment
Evaporative lithography in cells of arbitrary configuration allows for the creation of diverse particle deposition patterns due to the formation of a speci
- 6 December 2025
- Published by Springer Nature in The European Physical Journal E
- Vol. 48 (10-12) , 72
Shape of liquid meniscus in open cells of varying geometry: a combined study via simulation and experiment
Evaporative lithography in cells of arbitrary configuration allows for the creation of diverse particle deposition patterns due to the formation of a speci
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 092101
Nonuniform heating of a substrate in evaporative lithography
This work is devoted to a method to generate particle cluster assemblies and connected to evaporative lithography. Experiments are carried out using nonuniform evaporation of an isopropanol film containing polystyrene microspheres in a cylindrical cell. The local inhomogeneity of the vapor flux density is achieved by exploiting the temperature gradient. A copper rod is mounted in the central part of the bottom of the cell for further heating. The thermocapillary flow resulting from the surface tension gradient, due in turn to the temperature drop, transfers the particles that were originally at rest at the bottom of the cell. The effect of the initial thickness of the liquid layer on the height and base area of the cluster formed in the central region of the cell is studied. The velocity is measured using particle image velocimetry. A model describing the initial stage of the process is developed. The equations of heat transfer and thermal conductivity are used to define the temperature distribution in the liquid and in the cell. The fluid flow is simulated using the lubrication approximation. The particle distribution is modeled using the convection–diffusion equation. The evaporation flux density is calculated using the Hertz–Knudsen equation. The dependence of the liquid viscosity on the particle concentration is described by Mooney's formula. Numerical results show that the liquid film gradually becomes thinner in the central region, as the surface tension decreases with the increasing temperature. The liquid flow is directed to the heater near the substrate, and it transfers the particles to the center of the cell. The volume fraction of the particles increases over time in this region. The heat flow from the heater affects the geometry of the cluster for two reasons: First, the Marangoni flow velocity depends on the temperature gradient, and second, the decrease in film thickness near the heater depends on the temperature. The results of the simulation are in general agreement with the experimental data.
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 092101
Nonuniform heating of a substrate in evaporative lithography
This work is devoted to a method to generate particle cluster assemblies and connected to evaporative lithography. Experiments are carried out using nonuniform evaporation of an isopropanol film containing polystyrene microspheres in a cylindrical cell. The local inhomogeneity of the vapor flux density is achieved by exploiting the temperature gradient. A copper rod is mounted in the central part of the bottom of the cell for further heating. The thermocapillary flow resulting from the surface tension gradient, due in turn to the temperature drop, transfers the particles that were originally at rest at the bottom of the cell. The effect of the initial thickness of the liquid layer on the height and base area of the cluster formed in the central region of the cell is studied. The velocity is measured using particle image velocimetry. A model describing the initial stage of the process is developed. The equations of heat transfer and thermal conductivity are used to define the temperature distribution in the liquid and in the cell. The fluid flow is simulated using the lubrication approximation. The particle distribution is modeled using the convection–diffusion equation. The evaporation flux density is calculated using the Hertz–Knudsen equation. The dependence of the liquid viscosity on the particle concentration is described by Mooney's formula. Numerical results show that the liquid film gradually becomes thinner in the central region, as the surface tension decreases with the increasing temperature. The liquid flow is directed to the heater near the substrate, and it transfers the particles to the center of the cell. The volume fraction of the particles increases over time in this region. The heat flow from the heater affects the geometry of the cluster for two reasons: First, the Marangoni flow velocity depends on the temperature gradient, and second, the decrease in film thickness near the heater depends on the temperature. The results of the simulation are in general agreement with the experimental data.
- 1 September 2021
- Published by AIP Publishing
- Vol. 33 (9) , 092101
10.1063/5.0061713.1
This work is devoted to a method to generate particle cluster assemblies and connected to evaporative lithography. Experiments are carried out using nonuniform evaporation of an isopropanol film containing polystyrene microspheres in a cylindrical cell. The local inhomogeneity of the vapor flux density is achieved by exploiting the temperature gradient. A copper rod is mounted in the central part of the bottom of the cell for further heating. The thermocapillary flow resulting from the surface tension gradient, due in turn to the temperature drop, transfers the particles that were originally at rest at the bottom of the cell. The effect of the initial thickness of the liquid layer on the height and base area of the cluster formed in the central region of the cell is studied. The velocity is measured using particle image velocimetry. A model describing the initial stage of the process is developed. The equations of heat transfer and thermal conductivity are used to define the temperature distribution in the liquid and in the cell. The fluid flow is simulated using the lubrication approximation. The particle distribution is modeled using the convection–diffusion equation. The evaporation flux density is calculated using the Hertz–Knudsen equation. The dependence of the liquid viscosity on the particle concentration is described by Mooney's formula. Numerical results show that the liquid film gradually becomes thinner in the central region, as the surface tension decreases with the increasing temperature. The liquid flow is directed to the heater near the substrate, and it transfers the particles to the center of the cell. The volume fraction of the particles increases over time in this region. The heat flow from the heater affects the geometry of the cluster for two reasons: First, the Marangoni flow velocity depends on the temperature gradient, and second, the decrease in film thickness near the heater depends on the temperature. The results of the simulation are in general agreement with the experimental data.
- 1 September 2021
- Published by AIP Publishing
- Vol. 33 (9) , 092101
10.1063/5.0061713.1
This work is devoted to a method to generate particle cluster assemblies and connected to evaporative lithography. Experiments are carried out using nonuniform evaporation of an isopropanol film containing polystyrene microspheres in a cylindrical cell. The local inhomogeneity of the vapor flux density is achieved by exploiting the temperature gradient. A copper rod is mounted in the central part of the bottom of the cell for further heating. The thermocapillary flow resulting from the surface tension gradient, due in turn to the temperature drop, transfers the particles that were originally at rest at the bottom of the cell. The effect of the initial thickness of the liquid layer on the height and base area of the cluster formed in the central region of the cell is studied. The velocity is measured using particle image velocimetry. A model describing the initial stage of the process is developed. The equations of heat transfer and thermal conductivity are used to define the temperature distribution in the liquid and in the cell. The fluid flow is simulated using the lubrication approximation. The particle distribution is modeled using the convection–diffusion equation. The evaporation flux density is calculated using the Hertz–Knudsen equation. The dependence of the liquid viscosity on the particle concentration is described by Mooney's formula. Numerical results show that the liquid film gradually becomes thinner in the central region, as the surface tension decreases with the increasing temperature. The liquid flow is directed to the heater near the substrate, and it transfers the particles to the center of the cell. The volume fraction of the particles increases over time in this region. The heat flow from the heater affects the geometry of the cluster for two reasons: First, the Marangoni flow velocity depends on the temperature gradient, and second, the decrease in film thickness near the heater depends on the temperature. The results of the simulation are in general agreement with the experimental data.
- 1 November 2020
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 132
Thermocapillary deformations of a two-layer system of liquids under laser beam heating
- 1 November 2020
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 132
Thermocapillary deformations of a two-layer system of liquids under laser beam heating