Steven Collins
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Steven Collins has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Gerhard Fink
Aalto University
3 shared publications - Farid Vafadar
Department of Civil Engineering, Aalto University, Espoo, Finland
1 shared publication Gerhard Fink
1 shared publication
Latest Publications
- Open Access
- 13 May 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (3) , 1-10
Bayesian modeling of finger joints’ tensile and bending properties considering censored data
Finger joints (FJs) are longitudinal interlocking connections between timber boards commonly used in engineered wood products such as glued laminated timber beams. The mechanical properties of FJs, particularly tensile strength, are vital for the performance of such products; however, practical constraints often lead to testing FJs primarily in bending rather than tension. Therefore, it is crucial to investigate the relationship between tensile and bending strengths. The present study investigates this relationship using paired FJs. It further evaluates the predictability of FJ tensile and bending properties based on the dynamic modulus of elasticity of the connected timber boards. Tensile and bending tests were conducted, and censored data resulting from failures outside the FJs were handled using a hierarchical Bayesian linear regression method. The study proposes models to estimate FJ tensile strength from bending strength and to predict tensile and bending properties based on the dynamic modulus of elasticity of the connected timber boards. Model predictions are compared with experimental outcomes, indicating the effective integration of censored data. Results further show that excluding censored data underestimates FJ tensile and bending strength. The proposed Bayesian modeling procedure offers a means to connect failure modes with data types and appropriately address censored data. Such models can help to enhance quality control/production efficiency and the structural reliability of engineered wood products.
- 13 May 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (3) , 1-10
Open AccessBayesian modeling of finger joints’ tensile and bending properties considering censored data
Finger joints (FJs) are longitudinal interlocking connections between timber boards commonly used in engineered wood products such as glued laminated timber beams. The mechanical properties of FJs, particularly tensile strength, are vital for the performance of such products; however, practical constraints often lead to testing FJs primarily in bending rather than tension. Therefore, it is crucial to investigate the relationship between tensile and bending strengths. The present study investigates this relationship using paired FJs. It further evaluates the predictability of FJ tensile and bending properties based on the dynamic modulus of elasticity of the connected timber boards. Tensile and bending tests were conducted, and censored data resulting from failures outside the FJs were handled using a hierarchical Bayesian linear regression method. The study proposes models to estimate FJ tensile strength from bending strength and to predict tensile and bending properties based on the dynamic modulus of elasticity of the connected timber boards. Model predictions are compared with experimental outcomes, indicating the effective integration of censored data. Results further show that excluding censored data underestimates FJ tensile and bending strength. The proposed Bayesian modeling procedure offers a means to connect failure modes with data types and appropriately address censored data. Such models can help to enhance quality control/production efficiency and the structural reliability of engineered wood products.
- Open Access
- 10 July 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (6) , 1-12
Grain angle determination of silver birch by laser light scattering and tensile fracturing
Reliable non-destructive methods for grain angle determination are essential for the evaluation of mechanical properties of timber. In the present study, the detection of grain angle by means of laser light scattering patterns is investigated on small-scale specimens and timber boards of silver birch, along with the relationship to fracture angle and tensile strength. Results on small-scale specimens indicate applicability of laser scattering method, as the detected grain angles and the fracture angles show a strong correlation, $$r = 0.94$$ . Three-dimensional grain angles, derived from surface grain angles, show a well defined relationship to strength, which can be described with wood-based failure criteria from literature. Furthermore, the paper presents new findings regarding the detection of flame wood through laser scattering. It was shown that small-scale specimens with flame wood tend to have higher grain angles, higher density, and lower strength, relative to specimens without. Nevertheless, for timber boards, the influence of flame wood on the strength was insignificant.- 10 July 2022
- Published by Springer Nature in Materials and Structures
- Vol. 55 (6) , 1-12
Open AccessGrain angle determination of silver birch by laser light scattering and tensile fracturing
Reliable non-destructive methods for grain angle determination are essential for the evaluation of mechanical properties of timber. In the present study, the detection of grain angle by means of laser light scattering patterns is investigated on small-scale specimens and timber boards of silver birch, along with the relationship to fracture angle and tensile strength. Results on small-scale specimens indicate applicability of laser scattering method, as the detected grain angles and the fracture angles show a strong correlation, $$r = 0.94$$ . Three-dimensional grain angles, derived from surface grain angles, show a well defined relationship to strength, which can be described with wood-based failure criteria from literature. Furthermore, the paper presents new findings regarding the detection of flame wood through laser scattering. It was shown that small-scale specimens with flame wood tend to have higher grain angles, higher density, and lower strength, relative to specimens without. Nevertheless, for timber boards, the influence of flame wood on the strength was insignificant. - Open Access
- 29 June 2022
- Published by Elsevier in Construction and Building Materials
- Vol. 344
Modeling the tensile mechanical properties of silver birch timber boards
- 29 June 2022
- Published by Elsevier in Construction and Building Materials
- Vol. 344
Open AccessModeling the tensile mechanical properties of silver birch timber boards
- Open Access
- 7 August 2020
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 17 (2) , 121-128
Mechanical behaviour of sawn timber of silver birch under compression loading
Silver birch is a common European hardwood species possessing stiff and strong material properties. The mechanical properties of birch timber under compression loads are, however, not well defined as the influence of growth characteristics have largely been disregarded in experimental investigations. To address this, the present study investigated the effect of growth characteristics on the mechanical behaviour of birch sawn timber under compression loading, parallel and perpendicular to the grain direction. The results indicate knot size as the dominant parameter for both loading directions, whereas in specimen without knots, density, distance to pith and growth-ring width are dominant for parallel to grain loading and density and growth-ring orientation are dominant under perpendicular to grain loading. On selected specimens, local deformation and failure behaviour is further investigated by means of digital image correlation technique using a novel contrast pattern. Strain fields on specimens loaded parallel to grain reveal localized strain peaks at the cracks within knots and around the topside of knots where abrupt deviations in the grain orientation occur. Specimens loaded perpendicular to the grain display localized strain peaks near the pith and at growth-ring tangential angles around 45 .- 7 August 2020
- Published by Taylor & Francis in Wood Material Science & Engineering
- Vol. 17 (2) , 121-128
Open AccessMechanical behaviour of sawn timber of silver birch under compression loading
Silver birch is a common European hardwood species possessing stiff and strong material properties. The mechanical properties of birch timber under compression loads are, however, not well defined as the influence of growth characteristics have largely been disregarded in experimental investigations. To address this, the present study investigated the effect of growth characteristics on the mechanical behaviour of birch sawn timber under compression loading, parallel and perpendicular to the grain direction. The results indicate knot size as the dominant parameter for both loading directions, whereas in specimen without knots, density, distance to pith and growth-ring width are dominant for parallel to grain loading and density and growth-ring orientation are dominant under perpendicular to grain loading. On selected specimens, local deformation and failure behaviour is further investigated by means of digital image correlation technique using a novel contrast pattern. Strain fields on specimens loaded parallel to grain reveal localized strain peaks at the cracks within knots and around the topside of knots where abrupt deviations in the grain orientation occur. Specimens loaded perpendicular to the grain display localized strain peaks near the pith and at growth-ring tangential angles around 45 .