Jongsung Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jongsung Park has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
Dong-Weon Lee
9 shared publications- Arunkumar Shanmugasundaram
Chonnam National University
7 shared publications - Dong-Weon Lee
MEMS and Nanotechnology Laboratory, School of Mechanical Engineering, Chonnam National University, Gwangju, Republic of Korea
7 shared publications Ji-Kwan Kim
5 shared publicationsDong-Su Kim
3 shared publicationsYun-Jin Jeong
3 shared publications
Latest Publications
- 18 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 18731-18740
UV-Enhanced Room-Temperature Ammonia Detection Using a Ga₂O₃/Ti₃C₂Tₓ MXene Gas Sensor
The present study proposes a Ga2O3/Ti3C2Tx heterojunction-based gas sensor capable of detecting NH3 at room temperature. In this heterojunction, Ga2O3 nanorods, a type of metal oxide, were synthesized on two-dimensional Ti3C2Tx MXene using a hydrothermal method. The sensor was fabricated by drop-casting the Ga2O3/Ti3C2Tx composite onto interdigitated electrodes and evaluated under varying NH3 concentrations with and without UV illumination. The fabricated Ga2O3/Ti3C2Tx heterojunction exhibits enhanced reactivity with ammonia gas due to the high surface area of Ga2O3 and the superior electrical conductivity of Ti3C2Tx, resulting in a synergistic effect that significantly improves NH3 detection performance. Additionally, when exposed to UV light at room temperature, the Ga2O3/Ti3C2Tx gas sensor demonstrates an increased response and stable baseline resistance recovery. The response to 25 ppm NH₃ increased from 18.68% without UV to 23.47% with UV, highlighting the enhanced performance enabled by UV illumination. These findings indicate the sensor's potential for ammonia detection across a wide concentration range and highlight its promise for commercial applications in various environmental settings.
- 18 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 18731-18740
UV-Enhanced Room-Temperature Ammonia Detection Using a Ga₂O₃/Ti₃C₂Tₓ MXene Gas Sensor
The present study proposes a Ga2O3/Ti3C2Tx heterojunction-based gas sensor capable of detecting NH3 at room temperature. In this heterojunction, Ga2O3 nanorods, a type of metal oxide, were synthesized on two-dimensional Ti3C2Tx MXene using a hydrothermal method. The sensor was fabricated by drop-casting the Ga2O3/Ti3C2Tx composite onto interdigitated electrodes and evaluated under varying NH3 concentrations with and without UV illumination. The fabricated Ga2O3/Ti3C2Tx heterojunction exhibits enhanced reactivity with ammonia gas due to the high surface area of Ga2O3 and the superior electrical conductivity of Ti3C2Tx, resulting in a synergistic effect that significantly improves NH3 detection performance. Additionally, when exposed to UV light at room temperature, the Ga2O3/Ti3C2Tx gas sensor demonstrates an increased response and stable baseline resistance recovery. The response to 25 ppm NH₃ increased from 18.68% without UV to 23.47% with UV, highlighting the enhanced performance enabled by UV illumination. These findings indicate the sensor's potential for ammonia detection across a wide concentration range and highlight its promise for commercial applications in various environmental settings.
- 20 September 2024
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 422, 136667
Enhancing flexibility of smart bioresorbable vascular scaffolds through 3D printing using polycaprolactone and polylactic acid
- 20 September 2024
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 422, 136667
Enhancing flexibility of smart bioresorbable vascular scaffolds through 3D printing using polycaprolactone and polylactic acid
- Open Access
- 1 December 2021
- Published by Elsevier in Atmospheric Environment
- Vol. 266, 118717
Seasonal characteristics of PM1 in Seoul, Korea, measured using HR-ToF-Aerosol Mass Spectrometer in 2018
- 1 December 2021
- Published by Elsevier in Atmospheric Environment
- Vol. 266, 118717
Open AccessSeasonal characteristics of PM1 in Seoul, Korea, measured using HR-ToF-Aerosol Mass Spectrometer in 2018
- Open Access
ThetA -- fast and robust clustering via a distance parameter
Clustering is a fundamental problem in machine learning where distance-based approaches have dominated the field for many decades. This set of problems is often tackled by partitioning the data into K clusters where the number of clusters is chosen apriori. While significant progress has been made on these lines over the years, it is well established that as the number of clusters or dimensions increase, current approaches dwell in local minima resulting in suboptimal solutions. In this work, we propose a new set of distance threshold methods called Theta-based Algorithms (ThetA). Via experimental comparisons and complexity analyses we show that our proposed approach outperforms existing approaches in: a) clustering accuracy and b) time complexity. Additionally, we show that for a large class of problems, learning the optimal threshold is straightforward in comparison to learning K. Moreover, we show how ThetA can infer the sparsity of datasets in higher dimensions.
Open AccessThetA -- fast and robust clustering via a distance parameter
Clustering is a fundamental problem in machine learning where distance-based approaches have dominated the field for many decades. This set of problems is often tackled by partitioning the data into K clusters where the number of clusters is chosen apriori. While significant progress has been made on these lines over the years, it is well established that as the number of clusters or dimensions increase, current approaches dwell in local minima resulting in suboptimal solutions. In this work, we propose a new set of distance threshold methods called Theta-based Algorithms (ThetA). Via experimental comparisons and complexity analyses we show that our proposed approach outperforms existing approaches in: a) clustering accuracy and b) time complexity. Additionally, we show that for a large class of problems, learning the optimal threshold is straightforward in comparison to learning K. Moreover, we show how ThetA can infer the sparsity of datasets in higher dimensions.
- 31 July 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (11) , 115007
Large scale roll-to-roll production of polyurethane-acrylate-based hydrophobic film: a next-generation protection layer for solar devices
In the present study, we fabricate a hydrophobic film using a roll-to-roll technique capable of large-area continuous production and examine the film’s applicability to solar panels. The hydrophobic film was fabricated using a polyurethane-acrylate (PUA)-based UV-curable material, which has high optical transmittance and high releasability. The roll-to-roll system used in this study was custom manufactured to transfer micro-patterns of 20 μ m in size onto the PUA-based film. In addition, a UV irradiation device was attached to the system to enable production of the hydrophobic film at a rate of 150 mm min -1 . Through experiments, we confirmed that attaching the fabricated hydrophobic film not only enabled surface self-cleaning on the solar panels, but also ensured stable solar power generation. Thus, the hydrophobic film can be applied to installations that require external periodic cleaning and management, such as the exterior walls of buildings and solar panels.
- 31 July 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (11) , 115007
Large scale roll-to-roll production of polyurethane-acrylate-based hydrophobic film: a next-generation protection layer for solar devices
In the present study, we fabricate a hydrophobic film using a roll-to-roll technique capable of large-area continuous production and examine the film’s applicability to solar panels. The hydrophobic film was fabricated using a polyurethane-acrylate (PUA)-based UV-curable material, which has high optical transmittance and high releasability. The roll-to-roll system used in this study was custom manufactured to transfer micro-patterns of 20 μ m in size onto the PUA-based film. In addition, a UV irradiation device was attached to the system to enable production of the hydrophobic film at a rate of 150 mm min -1 . Through experiments, we confirmed that attaching the fabricated hydrophobic film not only enabled surface self-cleaning on the solar panels, but also ensured stable solar power generation. Thus, the hydrophobic film can be applied to installations that require external periodic cleaning and management, such as the exterior walls of buildings and solar panels.
- Open Access
- 27 January 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-13
Highly durable crack sensor integrated with silicone rubber cantilever for measuring cardiac contractility
To date, numerous biosensing platforms have been developed for assessing drug-induced cardiac toxicity by measuring the change in contractile force of cardiomyocytes. However, these low sensitivity, low-throughput, and time-consuming processes are severely limited in their real-time applications. Here, we propose a cantilever device integrated with a polydimethylsiloxane (PDMS)-encapsulated crack sensor to measure cardiac contractility. The crack sensor is chemically bonded to a PDMS thin layer that allows it to be operated very stably in culture media. The reliability of the proposed crack sensor has been improved dramatically compared to no encapsulation layer. The highly sensitive crack sensor continuously measures the cardiac contractility without changing its gauge factor for up to 26 days (>5 million heartbeats), while changes in contractile force induced by drugs are monitored using the crack sensor-integrated cantilever. Finally, experimental results are compared with those obtained via conventional optical methods to verify the feasibility of building a contraction-based drug-toxicity testing system.
- 27 January 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-13
Open AccessHighly durable crack sensor integrated with silicone rubber cantilever for measuring cardiac contractility
To date, numerous biosensing platforms have been developed for assessing drug-induced cardiac toxicity by measuring the change in contractile force of cardiomyocytes. However, these low sensitivity, low-throughput, and time-consuming processes are severely limited in their real-time applications. Here, we propose a cantilever device integrated with a polydimethylsiloxane (PDMS)-encapsulated crack sensor to measure cardiac contractility. The crack sensor is chemically bonded to a PDMS thin layer that allows it to be operated very stably in culture media. The reliability of the proposed crack sensor has been improved dramatically compared to no encapsulation layer. The highly sensitive crack sensor continuously measures the cardiac contractility without changing its gauge factor for up to 26 days (>5 million heartbeats), while changes in contractile force induced by drugs are monitored using the crack sensor-integrated cantilever. Finally, experimental results are compared with those obtained via conventional optical methods to verify the feasibility of building a contraction-based drug-toxicity testing system.
- 1 October 2019
- Published by Elsevier in Journal of Power Sources
- Vol. 436
Vertically aligned nanostructured FeOOH@MnO2 core shell electrode with better areal capacitance
- 1 October 2019
- Published by Elsevier in Journal of Power Sources
- Vol. 436
Vertically aligned nanostructured FeOOH@MnO2 core shell electrode with better areal capacitance
- 1 October 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 373, 68-77
Realizing the flexible and transparent highly-hydrophobic film through siloxane functionalized polyurethane-acrylate micro-pattern
- 1 October 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 373, 68-77
Realizing the flexible and transparent highly-hydrophobic film through siloxane functionalized polyurethane-acrylate micro-pattern
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 68-69
Liquid metal based flexible microfluidic device for wireless sensor applications
Liquid metal enabled wearable technology provides a promising for flexible electronics. This paper reports a Galinstan based flexible microfluidic device for wireless applications. The microchannel is made on the PDMS substrate and the Galinstan as a conductive material is injected into the microfluidic channel to form the sensor circuit. The microfluidic device uses capacitive sensing principle for measuring the physical quantity and inductive coupling-based readout method for wireless communication of data and power. The flexibility of the device is characterized by fixing it on the human body and can be applied in the remote areas to accomplish wireless sensing platform. The device demonstration displays exceptional electrical stability under high human motions like wrist flexion, hand movement and finger bending without any fall in performance during mechanical degradation. We believe our microfluidic device provides a benchmark for flexible wearable electronics in wireless and remote sensing applications.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 68-69
Liquid metal based flexible microfluidic device for wireless sensor applications
Liquid metal enabled wearable technology provides a promising for flexible electronics. This paper reports a Galinstan based flexible microfluidic device for wireless applications. The microchannel is made on the PDMS substrate and the Galinstan as a conductive material is injected into the microfluidic channel to form the sensor circuit. The microfluidic device uses capacitive sensing principle for measuring the physical quantity and inductive coupling-based readout method for wireless communication of data and power. The flexibility of the device is characterized by fixing it on the human body and can be applied in the remote areas to accomplish wireless sensing platform. The device demonstration displays exceptional electrical stability under high human motions like wrist flexion, hand movement and finger bending without any fall in performance during mechanical degradation. We believe our microfluidic device provides a benchmark for flexible wearable electronics in wireless and remote sensing applications.
- 1 February 2019
- Published by Elsevier in Microelectronic Engineering
- Vol. 206, 1-5
Biodegradable polymer material based smart stent: Wireless pressure sensor and 3D printed stent
- 1 February 2019
- Published by Elsevier in Microelectronic Engineering
- Vol. 206, 1-5
Biodegradable polymer material based smart stent: Wireless pressure sensor and 3D printed stent