Yudi Xiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yudi Xiao has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Zhe Zhang
State Key Laboratory of Intelligent Power Distribution Equipment and System, School of Electrical Engineering, Hebei University of Technology, Tianjin, China
7 shared publications - Michael A. E. Andersen
Department of Electrical and Photonics Engineering, Technical University of Denmark, Kongens Lyngby, Denmark
6 shared publications - Rafael Peña-Alzola
Electronic and Electrical Engineering, University of Strathclyde, 204 George St., Glasgow G1 1XW, UK
4 shared publications - Weijia Yuan
University of Strathclyde
4 shared publications - Abdelrahman Elwakeel
Department of Electronic and Electrical Engineering, University of Strathclyde, Glasgow, U.K.
3 shared publications - Min Zhang
University of Strathclyde
3 shared publications
Latest Publications
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
10 kW Cryogenic DC/DC Converter for Superconducting Propulsion Applications
Superconducting propulsion applications such as MAGLEV and electric aircraft rely on cryogenic cooling to reduce the losses and to enable their high-power density operation. However, if conventional power electronics is used into these systems, Bridging the thermal gradient from room temperature (300 K) to cryogenic temperatures requires sophisticated packaging and integration, introducing substantial design challenges. This article presents a cryogenic 270 V dc/dc converter specifically designed for powering the dc rails of superconducting motors, cables, and energy storage systems for cryogenic propulsion architectures. The article studies the use of Gallium Nitride (GaN) and Silicone Carbide (SiC) devices as a converter for cryogenic application, although GaN are known to have lower losses and faster switching at such low temperatures, this in turn would enable lighter more efficient electric transportation systems, SiC on the other hand, tend to have higher switching losses at cryogenic temperatures than GaN but tend to have readily available commercial of the shelf devices (COTs) at higher voltages and different packages. The article presents experimental and simulation results for both converter at room and cryogenic temperatures and how they would be integrated in a superconducting propulsion system.
- 20 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 36 (5) , 1-5
10 kW Cryogenic DC/DC Converter for Superconducting Propulsion Applications
Superconducting propulsion applications such as MAGLEV and electric aircraft rely on cryogenic cooling to reduce the losses and to enable their high-power density operation. However, if conventional power electronics is used into these systems, Bridging the thermal gradient from room temperature (300 K) to cryogenic temperatures requires sophisticated packaging and integration, introducing substantial design challenges. This article presents a cryogenic 270 V dc/dc converter specifically designed for powering the dc rails of superconducting motors, cables, and energy storage systems for cryogenic propulsion architectures. The article studies the use of Gallium Nitride (GaN) and Silicone Carbide (SiC) devices as a converter for cryogenic application, although GaN are known to have lower losses and faster switching at such low temperatures, this in turn would enable lighter more efficient electric transportation systems, SiC on the other hand, tend to have higher switching losses at cryogenic temperatures than GaN but tend to have readily available commercial of the shelf devices (COTs) at higher voltages and different packages. The article presents experimental and simulation results for both converter at room and cryogenic temperatures and how they would be integrated in a superconducting propulsion system.
- Top Cited PapersOpen Access
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 30646-30664
Review of Cryogenic Power Electronics for All-Electric Aircraft
To tackle emissions from the aviation industry and make it sustainable, research has been targeting electrifying aircraft. For this aim, articles have been focusing on how to replace regular jet engines with liquid hydrogen as fuel. This would be beneficial as hydrogen is expected to play a dual role, providing fuel for fuel cells to propel the aircraft electrically and to supply cooling to enable high-power density technologies such as superconducting machines and cryogenic power electronics circuits. However, using higher power density, especially cryogenic power electronics, can be challenging. This article investigates cryogenic power electronics for use on all-electric aircraft across different aspects, where it lays out how to integrate power electronics at cryogenic temperature into the architecture of the all-electric aircraft, how to use them with hydrogen fuel cells, and the voltage levels of the system. It reviews different semiconductor device technologies, circuit topologies, and passive devices to be used in power electronics circuitry, as well as logic circuits that are suitable for use at cryogenic temperatures. In addition, the article discusses the challenges of using semiconductor devices at such low temperatures, including the reliability, overall cooling, and recycling of hydrogen.
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 30646-30664
Top Cited PapersOpen AccessReview of Cryogenic Power Electronics for All-Electric Aircraft
To tackle emissions from the aviation industry and make it sustainable, research has been targeting electrifying aircraft. For this aim, articles have been focusing on how to replace regular jet engines with liquid hydrogen as fuel. This would be beneficial as hydrogen is expected to play a dual role, providing fuel for fuel cells to propel the aircraft electrically and to supply cooling to enable high-power density technologies such as superconducting machines and cryogenic power electronics circuits. However, using higher power density, especially cryogenic power electronics, can be challenging. This article investigates cryogenic power electronics for use on all-electric aircraft across different aspects, where it lays out how to integrate power electronics at cryogenic temperature into the architecture of the all-electric aircraft, how to use them with hydrogen fuel cells, and the voltage levels of the system. It reviews different semiconductor device technologies, circuit topologies, and passive devices to be used in power electronics circuitry, as well as logic circuits that are suitable for use at cryogenic temperatures. In addition, the article discusses the challenges of using semiconductor devices at such low temperatures, including the reliability, overall cooling, and recycling of hydrogen.
- 17 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (3) , 1-7
Characterization of 650-V GaN Transistors at Cryogenic Temperature in All-Electric Aircraft Applications
With the growing electrification of aircraft, power electronics is playing an increasingly vital role in driving this transformation. It is expected that some all-electric aircraft to utilizes liquid hydrogen (LH2) as power fuel as well as coolant, which opens the possibility of utilizing cryogenic power electronics which offers higher efficiency and faster switching speeds than its room-temperature counterpart. Literature has shown the most efficient semiconductor switches at cryogenic temperatures is gallium nitride (GaN). Thus this paper focuses on studying the characteristics of 650 V GaN transistor at room temperature and cryogenic temperature at 77 K. Forward and breakdown voltage tests are performed to characterize the device. With the extracted device characteristics, a buck converter is simulated to estimate its efficiency and room and cryogenic temperatures.
- 17 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (3) , 1-7
Characterization of 650-V GaN Transistors at Cryogenic Temperature in All-Electric Aircraft Applications
With the growing electrification of aircraft, power electronics is playing an increasingly vital role in driving this transformation. It is expected that some all-electric aircraft to utilizes liquid hydrogen (LH2) as power fuel as well as coolant, which opens the possibility of utilizing cryogenic power electronics which offers higher efficiency and faster switching speeds than its room-temperature counterpart. Literature has shown the most efficient semiconductor switches at cryogenic temperatures is gallium nitride (GaN). Thus this paper focuses on studying the characteristics of 650 V GaN transistor at room temperature and cryogenic temperature at 77 K. Forward and breakdown voltage tests are performed to characterize the device. With the extracted device characteristics, a buck converter is simulated to estimate its efficiency and room and cryogenic temperatures.
- Open Access
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 1172-1181
Design Automation Using Exclusion-Based Hierarchical Computation for Power Electronics Converters in Harsh Environments
Designing power electronics converters for harsh environments is challenging due to the absence of components' performance under harsh conditions, the frequent transition and data-passing among various software, and the time-consuming and computationally heavy work flow. This paper promotes using design automation to address the aforementioned design challenges. The implementations include public-accessible component databases, automated co-action among circuit simulators and finite element simulations to perform electrical, electromagnetic and thermal co-design, and finally an exclusionbased work flow with hierarchical computation to reduce computational load. The theorized framework is exemplified on designing a real world 175 ◦C 1.5kW Three-level Neutral-point-clamped dc-dc converter. A database containing the high-temperature characteristics of SiC MOSFETs and ferrites is established and shared through a web application with graphical user interface. In 310 min, the program, which includes computationally heavy 3D finite element simulation, delivers design output after evaluating the converter's electrical, electromagnetic and thermal performance under 10 million parameter sets. Finally, a 1.5kW dc-dc converter prototype is built and tested in 175 ◦C ambient temperature to verify the quality of the design output
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 1172-1181
Open AccessDesign Automation Using Exclusion-Based Hierarchical Computation for Power Electronics Converters in Harsh Environments
Designing power electronics converters for harsh environments is challenging due to the absence of components' performance under harsh conditions, the frequent transition and data-passing among various software, and the time-consuming and computationally heavy work flow. This paper promotes using design automation to address the aforementioned design challenges. The implementations include public-accessible component databases, automated co-action among circuit simulators and finite element simulations to perform electrical, electromagnetic and thermal co-design, and finally an exclusionbased work flow with hierarchical computation to reduce computational load. The theorized framework is exemplified on designing a real world 175 ◦C 1.5kW Three-level Neutral-point-clamped dc-dc converter. A database containing the high-temperature characteristics of SiC MOSFETs and ferrites is established and shared through a web application with graphical user interface. In 310 min, the program, which includes computationally heavy 3D finite element simulation, delivers design output after evaluating the converter's electrical, electromagnetic and thermal performance under 10 million parameter sets. Finally, a 1.5kW dc-dc converter prototype is built and tested in 175 ◦C ambient temperature to verify the quality of the design output
- 20 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 8970-8978
ZVS Design in Full-SiC Three-Level Neutral-Point-Clamped DC–DC Converter Considering Quasi-Linear Output Capacitance $C_{oss}$The Three-level Neutral-point-clamped (TLNPC) dc-dc converter is a popular topology for applications with high input voltage due to its simplicity of modulation, capability of withstanding high input voltage, and Zero-voltage-switching (ZVS) operation. Regarding mitigating the voltage ringing on secondary side, energy recovery approach is preferred to RCD approach for the sake of high efficiency and small component counts. This paper demonstrates that, using recovery approach in a Silicon Carbide (SiC) based TLNPC dc-dc converter causes hard-switching of the outer switches due to the quasi-linear output capacitance Coss of SiC MOSFETs. The ZVS design of a full-SiC TLNPC converter must not follow conventional methods for Silicon (Si) based converters. To address this issue, a modified design approach, which can guarantee ZVS of all switches in a full-SiC TLNPC dc-dc converter, is introduced and discussed. All of the analysis is verified on a 3 kW full-SiC TLNPC prototype, which has rated input voltage of 1.2 kV, output voltage of 600 V, and achieves ZVS in the output power range of 1.2 kW $\sim$ 3 kW.
- 20 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 8970-8978
ZVS Design in Full-SiC Three-Level Neutral-Point-Clamped DC–DC Converter Considering Quasi-Linear Output Capacitance $C_{oss}$The Three-level Neutral-point-clamped (TLNPC) dc-dc converter is a popular topology for applications with high input voltage due to its simplicity of modulation, capability of withstanding high input voltage, and Zero-voltage-switching (ZVS) operation. Regarding mitigating the voltage ringing on secondary side, energy recovery approach is preferred to RCD approach for the sake of high efficiency and small component counts. This paper demonstrates that, using recovery approach in a Silicon Carbide (SiC) based TLNPC dc-dc converter causes hard-switching of the outer switches due to the quasi-linear output capacitance Coss of SiC MOSFETs. The ZVS design of a full-SiC TLNPC converter must not follow conventional methods for Silicon (Si) based converters. To address this issue, a modified design approach, which can guarantee ZVS of all switches in a full-SiC TLNPC dc-dc converter, is introduced and discussed. All of the analysis is verified on a 3 kW full-SiC TLNPC prototype, which has rated input voltage of 1.2 kV, output voltage of 600 V, and achieves ZVS in the output power range of 1.2 kW $\sim$ 3 kW.
- 4 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 14831-14849
Review of High-Temperature Power Electronics Converters
Power electronics converters operating at elevated temperature usually have degraded performance, such as reduced efficiency, lower noise immunity, and decreased system reliability, compared to those operating at room temperature. Nevertheless, harsh-environment applications, such as deep earth drilling, automotive, avionics, and space exploration, have been utilizing converters in high-temperature environments and are continuously pushing the temperature limits higher and higher with the advances in device technologies and converter design methodologies. This article starts with a literature study to identify the temperature dependence and the temperature limits of individual components. Then, published works about high-temperature converters are examined. Their selection of components is compared. Experimental results are analyzed to reflect on the efficacy of different component selections. Finally, since the latest published high-temperature converter was developed more than five years ago, a 1-kV input, 520-V output, 1-kW, $150$ °C-ambient-temperature-rated dc–dc converter is designed with state-of-the-art devices. Based on the literature review, and the test of the $150$ °C prototype, the main challenges of designing high-temperature power electronics converters are identified and concluded to be time-consuming, difficult, and expensive characterization of components, lack of accurate and computationally efficient models of converters, and optimizing component selection within short development time.
- 4 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (12) , 14831-14849
Review of High-Temperature Power Electronics Converters
Power electronics converters operating at elevated temperature usually have degraded performance, such as reduced efficiency, lower noise immunity, and decreased system reliability, compared to those operating at room temperature. Nevertheless, harsh-environment applications, such as deep earth drilling, automotive, avionics, and space exploration, have been utilizing converters in high-temperature environments and are continuously pushing the temperature limits higher and higher with the advances in device technologies and converter design methodologies. This article starts with a literature study to identify the temperature dependence and the temperature limits of individual components. Then, published works about high-temperature converters are examined. Their selection of components is compared. Experimental results are analyzed to reflect on the efficacy of different component selections. Finally, since the latest published high-temperature converter was developed more than five years ago, a 1-kV input, 520-V output, 1-kW, $150$ °C-ambient-temperature-rated dc–dc converter is designed with state-of-the-art devices. Based on the literature review, and the test of the $150$ °C prototype, the main challenges of designing high-temperature power electronics converters are identified and concluded to be time-consuming, difficult, and expensive characterization of components, lack of accurate and computationally efficient models of converters, and optimizing component selection within short development time.
- 18 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (6) , 6480-6500
A Universal Power Flow Model for Dual Active Bridge-Based Converters With Phase Shift Modulation
In this paper, a universal power flow model for the Dual Active Bridge (DAB) based dc-dc converters with phase-shift modulation is derived. The model considers the lossy components, the dead time, and the resonant commutations of the converters. A power flow model for the Partial Parallel Dual Active Bridge (P2DAB) converter is generated from the universal power flow model. Based on the calculations, the power plateau phenomenon and the anti-power phenomenon, as well as their causes and influences are discussed. Because of the zero-reactive-power-loss in the lagging full-bridge, the zero-voltage-turn-on of all of the switches, and the zero-current-commutation of the switches in the lagging full-bridge during the power plateau, a hypothesis, which claims that the converter is more efficient in the power plateau operation than in other operation modes, is made. A laboratory prototype of the P2DAB converter is constructed. The analysis about the power plateau and the anti-power phenomenon is verified, as well as the proposed hypothesis is proved. Compared against the measured power, the model for the (P2DAB) converter has the maximum error less than 10%. Therefore, the validity of the universal power flow model is verified.
- 18 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (6) , 6480-6500
A Universal Power Flow Model for Dual Active Bridge-Based Converters With Phase Shift Modulation
In this paper, a universal power flow model for the Dual Active Bridge (DAB) based dc-dc converters with phase-shift modulation is derived. The model considers the lossy components, the dead time, and the resonant commutations of the converters. A power flow model for the Partial Parallel Dual Active Bridge (P2DAB) converter is generated from the universal power flow model. Based on the calculations, the power plateau phenomenon and the anti-power phenomenon, as well as their causes and influences are discussed. Because of the zero-reactive-power-loss in the lagging full-bridge, the zero-voltage-turn-on of all of the switches, and the zero-current-commutation of the switches in the lagging full-bridge during the power plateau, a hypothesis, which claims that the converter is more efficient in the power plateau operation than in other operation modes, is made. A laboratory prototype of the P2DAB converter is constructed. The analysis about the power plateau and the anti-power phenomenon is verified, as well as the proposed hypothesis is proved. Compared against the measured power, the model for the (P2DAB) converter has the maximum error less than 10%. Therefore, the validity of the universal power flow model is verified.
- 10 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (8) , 6729-6738
GaN-Based 1-MHz Partial Parallel Dual Active Bridge Converter With Integrated Magnetics
In this paper, a partial parallel dual active bridge (PPDAB) converter is proposed to lower the current stress over the switching devices on the low-voltage (LV) side. Gallium Nitride (GaN) transistors are used to improve efficiency and power density at 1 MHz switching frequency. Moreover, in order to reduce the number of magnetic components and achieve more compact design, with a unique three-leg core geometry, a new method of integrating three transformers and their associated interfacing inductors is proposed. The integration is able to shorten winding length and therefore reduces winding dc resistance. Moreover, wounding the secondary windings on each outer leg in the core enlarges leakage inductance, which can serve as the interfacing inductor Lac in the PPDAB converter. Given that, a reluctance model to analyze coupling effect of the secondary windings as well as their current balance is derived and validated by finite element simulations. Based on both calculations and simulations, the proposed integrated transformer is found to be functionally equivalent to three discrete transformers, in which their primary windings are connected in series, and the additional Lac inductor. Given the same number of the turns of the windings in each parallel module, the ac currents in these three secondary windings can inherently balance.
- 10 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (8) , 6729-6738
GaN-Based 1-MHz Partial Parallel Dual Active Bridge Converter With Integrated Magnetics
In this paper, a partial parallel dual active bridge (PPDAB) converter is proposed to lower the current stress over the switching devices on the low-voltage (LV) side. Gallium Nitride (GaN) transistors are used to improve efficiency and power density at 1 MHz switching frequency. Moreover, in order to reduce the number of magnetic components and achieve more compact design, with a unique three-leg core geometry, a new method of integrating three transformers and their associated interfacing inductors is proposed. The integration is able to shorten winding length and therefore reduces winding dc resistance. Moreover, wounding the secondary windings on each outer leg in the core enlarges leakage inductance, which can serve as the interfacing inductor Lac in the PPDAB converter. Given that, a reluctance model to analyze coupling effect of the secondary windings as well as their current balance is derived and validated by finite element simulations. Based on both calculations and simulations, the proposed integrated transformer is found to be functionally equivalent to three discrete transformers, in which their primary windings are connected in series, and the additional Lac inductor. Given the same number of the turns of the windings in each parallel module, the ac currents in these three secondary windings can inherently balance.
- 22 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (11) , 11988-12002
Impact on ZVS Operation by Splitting Inductance to Both Sides of Transformer for 1-MHz GaN Based DAB Converter
Dual active bridge (DAB) converter's zero-voltage-switching (ZVS) and its range extension have been studied intensively. However, this paper proves that the external inductance location, i.e. placing on which side of the transformer, does affect the ZVS operation due to transformers' parasitic capacitances, in particular at a high switching frequency of higher than 1 MHz. Thus, this paper, for the first time, gives the mathematical model of the resonant transition during the dead time and thereby analyzes partial hard switching under different modulation schemes with consideration of transformer's parasitic capacitances. From the analysis of ZVS operation, the solution of splitting the interfacing inductance and placing them on both sides of the transformer is proposed and its associated methodology of selecting these inductances is introduced. It extends the ZVS for all the switching devices, therefore, enhance the efficiency or move losses away from the critical semiconductor devices. Finally, the theoretical analysis is verified by the experimental results from a 1 MHz Gallium Nitride (GaN) based DAB converter prototype.
- 22 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (11) , 11988-12002
Impact on ZVS Operation by Splitting Inductance to Both Sides of Transformer for 1-MHz GaN Based DAB Converter
Dual active bridge (DAB) converter's zero-voltage-switching (ZVS) and its range extension have been studied intensively. However, this paper proves that the external inductance location, i.e. placing on which side of the transformer, does affect the ZVS operation due to transformers' parasitic capacitances, in particular at a high switching frequency of higher than 1 MHz. Thus, this paper, for the first time, gives the mathematical model of the resonant transition during the dead time and thereby analyzes partial hard switching under different modulation schemes with consideration of transformer's parasitic capacitances. From the analysis of ZVS operation, the solution of splitting the interfacing inductance and placing them on both sides of the transformer is proposed and its associated methodology of selecting these inductances is introduced. It extends the ZVS for all the switching devices, therefore, enhance the efficiency or move losses away from the critical semiconductor devices. Finally, the theoretical analysis is verified by the experimental results from a 1 MHz Gallium Nitride (GaN) based DAB converter prototype.
- Open Access
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2319-2324
Grid-connected photovoltaic micro-inverter with new hybrid control LLC resonant converter
A high-efficiency photovoltaic (PV) micro-inverter consisting of two power stages i.e. a LLC resonant converter with a new hybrid control scheme and a dc-ac inverter is proposed, studied and designed in this paper. In the first power stage, the new hybrid control combining pulse-frequency modulation (PFM) and phase-shift pulse-width modulation (PS-PWM) is employed on a full-bridge LLC dc-dc converter, in order to achieve high efficiency when PV output voltage varies in a wide range. Moreover, a maximum power point tracking (MPPT) method based on power perturbation is implemented in the dc-ac inverter. Therefore, the complexity of regulating LLC converter can be reduced effectively, and efficiency optimal design can be carried out through the proposed designing procedure for the resonant tank of LLC converter. Finally, a prototype of the proposed PV micro-inverter (PVMI) is developed with rated power of 250W and output voltage of 220VAC/50Hz. The experiment shows that the peak efficiency of the PVMI is 95.5%, where efficiency of LLC converter is up to 97.7%, and the MPPT accuracy is more than 99%. Thus the validity of the proposed system structure, design and control method is verified.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2319-2324
Open AccessGrid-connected photovoltaic micro-inverter with new hybrid control LLC resonant converter
A high-efficiency photovoltaic (PV) micro-inverter consisting of two power stages i.e. a LLC resonant converter with a new hybrid control scheme and a dc-ac inverter is proposed, studied and designed in this paper. In the first power stage, the new hybrid control combining pulse-frequency modulation (PFM) and phase-shift pulse-width modulation (PS-PWM) is employed on a full-bridge LLC dc-dc converter, in order to achieve high efficiency when PV output voltage varies in a wide range. Moreover, a maximum power point tracking (MPPT) method based on power perturbation is implemented in the dc-ac inverter. Therefore, the complexity of regulating LLC converter can be reduced effectively, and efficiency optimal design can be carried out through the proposed designing procedure for the resonant tank of LLC converter. Finally, a prototype of the proposed PV micro-inverter (PVMI) is developed with rated power of 250W and output voltage of 220VAC/50Hz. The experiment shows that the peak efficiency of the PVMI is 95.5%, where efficiency of LLC converter is up to 97.7%, and the MPPT accuracy is more than 99%. Thus the validity of the proposed system structure, design and control method is verified.