Walter Jesus Paucar Casas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Walter Jesus Paucar Casas has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Herbert Martins Gomes
Department of Mechanical Engineering, Federal University of Rio Grande do Sul, Porto Alegre, Brazil
3 shared publications - Ederval de Souza Lisboa
Group of Mechanics of Materials and Structures, Cachoeira do Sul Campus
2 shared publications - João Baptista Dias Moreira
Department of Mechatronics and Mechanical Systems Engineering, School of Engineering, University of São Paulo, São Paulo, Brazil
2 shared publications - Luis Roberto Centeno Drehmer
Campus Cachoeira do Sul, Federal University of Santa Maria, Cachoeira do Sul, Rio Grande do Sul, Brazil
2 shared publications - Maicol Laurenza
Department of Engineering, Niccolò Cusano University, Rome, Italy
2 shared publications Carlos Eduardo Henke Viganico
Department of Mechanical Engineering, Federal University of Rio Grande do Sul, Porto Alegre, Rio Grande do Sul, Brazil
1 shared publication
Latest Publications
- Open Access
- 24 October 2026
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 14 (8) , 604
Identification and Optimization of Truck Suspension Parameters to Enhance Comfort using the QPSO Algorithm
Purpose: Road irregularities generate vibrations and noise in vehicles, which are major occupational factors affecting drivers'' comfort. While many studies propose new suspension systems and use numerical models to optimize stiffness and damping parameters, they typically assume these parameters are known beforehand. This study addresses a gap by first identifying the actual effective stiffness and damping properties of an in-service truck from field measurements, and then using the experimentally calibrated model to optimize ride comfort. The main research question is whether this two-step approach can reduce vertical accelerations and improve comfort more effectively than conventional methods. Methods: Accelerometers were installed at several points on the vehicle axles to collect experimental data during a test campaign at speeds of 15, 20, and 30 km/h. The Quantum Particle Swarm Optimization (QPSO) algorithm was employed to identify the suspension''s stiffness and damping parameters by minimizing the differences in vertical accelerations between the numerical model and experimental values. The performance of QPSO was compared against several other metaheuristics. Results: QPSO exhibited faster convergence and lower final objective-function values than the other algorithms. The identified parameters yielded vertical accelerations that differed, on average, by 10.98%, 10.39%, and 10.47% from experimental measurements at 15, 20, and 30 km/h, respectively. Subsequent optimization for ride comfort resulted in a reduction of up to 18.41% in the RMS value of ISO 2631-weighted accelerations. Conclusion: The proposed methodology successfully calibrates and optimizes suspension parameters using experimental data, leading to meaningful improvements in ride comfort. This approach offers a practical alternative to studies that rely on assumed parameters, with potential applications in vehicle design and performance verification.
- 24 October 2026
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 14 (8) , 604
Open AccessIdentification and Optimization of Truck Suspension Parameters to Enhance Comfort using the QPSO Algorithm
Purpose: Road irregularities generate vibrations and noise in vehicles, which are major occupational factors affecting drivers'' comfort. While many studies propose new suspension systems and use numerical models to optimize stiffness and damping parameters, they typically assume these parameters are known beforehand. This study addresses a gap by first identifying the actual effective stiffness and damping properties of an in-service truck from field measurements, and then using the experimentally calibrated model to optimize ride comfort. The main research question is whether this two-step approach can reduce vertical accelerations and improve comfort more effectively than conventional methods. Methods: Accelerometers were installed at several points on the vehicle axles to collect experimental data during a test campaign at speeds of 15, 20, and 30 km/h. The Quantum Particle Swarm Optimization (QPSO) algorithm was employed to identify the suspension''s stiffness and damping parameters by minimizing the differences in vertical accelerations between the numerical model and experimental values. The performance of QPSO was compared against several other metaheuristics. Results: QPSO exhibited faster convergence and lower final objective-function values than the other algorithms. The identified parameters yielded vertical accelerations that differed, on average, by 10.98%, 10.39%, and 10.47% from experimental measurements at 15, 20, and 30 km/h, respectively. Subsequent optimization for ride comfort resulted in a reduction of up to 18.41% in the RMS value of ISO 2631-weighted accelerations. Conclusion: The proposed methodology successfully calibrates and optimizes suspension parameters using experimental data, leading to meaningful improvements in ride comfort. This approach offers a practical alternative to studies that rely on assumed parameters, with potential applications in vehicle design and performance verification.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Oceanic Engineering
- Vol. 51 (2) , 1106-1128
Toward Scalable Energy-Efficient Rendezvous Optimization for Multiagent Marine Applications
Uncrewed surface vehicles (USVs) and autonomous surface vehicles (ASVs) are increasingly utilized for a variety of maritime missions, offering the benefits of enhanced safety and reduced operational costs by minimizing human risk, especially in hostile environments. Despite their clear advantages, rendezvous operations, which are essential for critical tasks such as resource exchange and recharging, present significant challenges in terms of energy efficiency and proper coordination in dynamic oceanic settings. This study proposes an energy-efficient rendezvous planning framework for autonomous vessels, focusing specifically on optimizing energy consumption and improving response times during emergency scenarios. The framework uses a multiobjective particle swarm optimization algorithm. This approach integrates propulsion optimization to reduce overall energy use in extended maneuvers while considering sea conditions and dynamic obstacles by using a visibility graph-based avoidance system. The framework proves to be robust and scalable for complex multiagent missions, consistently delivering solutions that balance energy consumption and mission time. The computation for planning with up to 15 vessels consistently remains under 5% of the total mission duration, confirming its effectiveness.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Oceanic Engineering
- Vol. 51 (2) , 1106-1128
Toward Scalable Energy-Efficient Rendezvous Optimization for Multiagent Marine Applications
Uncrewed surface vehicles (USVs) and autonomous surface vehicles (ASVs) are increasingly utilized for a variety of maritime missions, offering the benefits of enhanced safety and reduced operational costs by minimizing human risk, especially in hostile environments. Despite their clear advantages, rendezvous operations, which are essential for critical tasks such as resource exchange and recharging, present significant challenges in terms of energy efficiency and proper coordination in dynamic oceanic settings. This study proposes an energy-efficient rendezvous planning framework for autonomous vessels, focusing specifically on optimizing energy consumption and improving response times during emergency scenarios. The framework uses a multiobjective particle swarm optimization algorithm. This approach integrates propulsion optimization to reduce overall energy use in extended maneuvers while considering sea conditions and dynamic obstacles by using a visibility graph-based avoidance system. The framework proves to be robust and scalable for complex multiagent missions, consistently delivering solutions that balance energy consumption and mission time. The computation for planning with up to 15 vessels consistently remains under 5% of the total mission duration, confirming its effectiveness.
- 21 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (7) , 4554-4566
Safety assessment of a tractor semi-trailer based on handling and stability maneuvers
The UN General Assembly proclaimed the Decade of Action for Road Safety 2021–2030, aiming to prevent at least 50% of road traffic deaths and injuries by 2030. A safe transport system is mandatory for road freight, where heavy vehicle accidents cause more severe personal and financial consequences. In this context, the purpose of this work is to determine the limits of the main handling and stability parameters of a tractor semi-trailer based on maneuvers such as Steady State Cornering (SSC), Double Lane Change (DLC), and Tilt Table Ratio (TTR). The methodology consisted in modeling the tractor semi-trailer using MSC.Adams/Car™ software validated with experimental procedures. The tractor semi-trailer was modeled as a multibody system (MBS), which considers the chassis of a semi-trailer a flexible body using the modal superposition method and the component modal synthesis method, based on an analysis by the finite element method (FEM). In addition, leaf spring suspensions were also considered flexible bodies, and a specific Pacejka tire model was used. Numerical simulations of the SSC maneuver were validated experimentally through RMS values of the rolling angle and lateral acceleration at speeds of 25 and 30 km/h. The DLC maneuver, in turn, was validated at speeds of 35 and 45 km/h, with slight differences observed as a function of human behavior. The simulations indicated that the vehicle may roll over at speeds of close to 38 km/h during SSC and at 55 km/h during DLC, with lateral acceleration between 0.35 g and 0.41 g , respectively. The TTR simulations showed a corresponding rollover limit with a lateral acceleration of 0.35 g . Lastly, the results of this work can be used for safety assessments of the lateral dynamic behavior of semi-trailers.
- 21 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (7) , 4554-4566
Safety assessment of a tractor semi-trailer based on handling and stability maneuvers
The UN General Assembly proclaimed the Decade of Action for Road Safety 2021–2030, aiming to prevent at least 50% of road traffic deaths and injuries by 2030. A safe transport system is mandatory for road freight, where heavy vehicle accidents cause more severe personal and financial consequences. In this context, the purpose of this work is to determine the limits of the main handling and stability parameters of a tractor semi-trailer based on maneuvers such as Steady State Cornering (SSC), Double Lane Change (DLC), and Tilt Table Ratio (TTR). The methodology consisted in modeling the tractor semi-trailer using MSC.Adams/Car™ software validated with experimental procedures. The tractor semi-trailer was modeled as a multibody system (MBS), which considers the chassis of a semi-trailer a flexible body using the modal superposition method and the component modal synthesis method, based on an analysis by the finite element method (FEM). In addition, leaf spring suspensions were also considered flexible bodies, and a specific Pacejka tire model was used. Numerical simulations of the SSC maneuver were validated experimentally through RMS values of the rolling angle and lateral acceleration at speeds of 25 and 30 km/h. The DLC maneuver, in turn, was validated at speeds of 35 and 45 km/h, with slight differences observed as a function of human behavior. The simulations indicated that the vehicle may roll over at speeds of close to 38 km/h during SSC and at 55 km/h during DLC, with lateral acceleration between 0.35 g and 0.41 g , respectively. The TTR simulations showed a corresponding rollover limit with a lateral acceleration of 0.35 g . Lastly, the results of this work can be used for safety assessments of the lateral dynamic behavior of semi-trailers.
- 7 April 2025
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 53 (11) , 7435-7463
Evolutionary topology optimization applied to a system with fluid-structure interaction via maximization of the natural frequency
- 7 April 2025
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 53 (11) , 7435-7463
Evolutionary topology optimization applied to a system with fluid-structure interaction via maximization of the natural frequency
- 22 January 2025
- Published by Taylor & Francis in Ships and Offshore Structures
- p. 1-13
Analysis of the dynamic response of a model of an oyster farming structure
- 22 January 2025
- Published by Taylor & Francis in Ships and Offshore Structures
- p. 1-13
Analysis of the dynamic response of a model of an oyster farming structure
- 23 June 2022
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 51 (12) , 7076-7101
An interval-based multi-objective robust design optimization for vehicle dynamics
This study presents an Interval-based Multi-objective Robust Design Optimization (IB-MORDO) algorithm applied to a vehicle dynamic problem. The proposed algorithm optimizes a full 15 degrees-of-freedom (15-DOF) vehicle model, subjected to a double-lane change (DLC) maneuver under random road profiles, to attain driver comfort and safety. This study does not make assumptions about uncertain parameter statistics; instead, the uncertainties are quantified using a non-probabilistic α-cut level interval analysis. These uncertainties are applied to the system parameters and design variables to ensure robust results. After the optimization process, the root mean square (RMS) vertical acceleration at the driver’s seat resulted in a robust solution of 1.041 m/s2 and a parameter interval radius (IR) equals to 0.631 m/s2, whereas the RMS lateral acceleration at the driver’s seat resulted in a solution of 1.908 m/s2 with an interval radius of 0.168 m/s2. Unlike the Robust Optimization, the algorithm proposed herein considers uncertainties at system parameters and design variables without assuming any statistical data.
- 23 June 2022
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 51 (12) , 7076-7101
An interval-based multi-objective robust design optimization for vehicle dynamics
This study presents an Interval-based Multi-objective Robust Design Optimization (IB-MORDO) algorithm applied to a vehicle dynamic problem. The proposed algorithm optimizes a full 15 degrees-of-freedom (15-DOF) vehicle model, subjected to a double-lane change (DLC) maneuver under random road profiles, to attain driver comfort and safety. This study does not make assumptions about uncertain parameter statistics; instead, the uncertainties are quantified using a non-probabilistic α-cut level interval analysis. These uncertainties are applied to the system parameters and design variables to ensure robust results. After the optimization process, the root mean square (RMS) vertical acceleration at the driver’s seat resulted in a robust solution of 1.041 m/s2 and a parameter interval radius (IR) equals to 0.631 m/s2, whereas the RMS lateral acceleration at the driver’s seat resulted in a solution of 1.908 m/s2 with an interval radius of 0.168 m/s2. Unlike the Robust Optimization, the algorithm proposed herein considers uncertainties at system parameters and design variables without assuming any statistical data.
- 26 July 2021
- Published by Emerald Publishing in Engineering Computations
- Vol. 39 (3) , 916-942
Pareto-optimal front for multi-objective optimization of the suspension of a full-vehicle model in the frequency domain
Purpose: This study aims to propose a complete and powerful methodology that allows the optimization of the passive suspension system of vehicles, which simultaneously takes comfort and safety into account and provides a set of optimal solutions through a Pareto-optimal front, in a low computational time.Design/methodology/approach: Unlike papers that consider simple vehicle models (quarter vehicle model or half car model) and/or simplified road profiles (harmonic excitation, for example) and/or perform a single-objective optimization and/or execute the dynamic analysis in the time domain, this paper presents an effective and fast methodology for the multi-objective optimization of the suspension system of a full-car model (including the driver seat) traveling on an irregular road profile, whose dynamic response is determined in the frequency domain, considerably reducing computational time.Findings: The results showed that there was a reduction of 28% in the driver seat vertical acceleration weighted root mean square (RMS) value of the proposed model, which is directly related to comfort, and, simultaneously, an improvement or constancy concerning safety, with low computational cost. Hence, the proposed methodology can be indicated as a successful tool for the optimal design of the suspension systems, considering, simultaneously, comfort and safety.Originality/value: Despite the extensive literature on optimizing vehicle passive suspension systems, papers combining multi-objective optimization presenting a Pareto-optimal front as a set of optimal results, a full-vehicle model (including the driver seat), an irregular road profile and the determination of the dynamic response in the frequency domain are not found.
- 26 July 2021
- Published by Emerald Publishing in Engineering Computations
- Vol. 39 (3) , 916-942
Pareto-optimal front for multi-objective optimization of the suspension of a full-vehicle model in the frequency domain
Purpose: This study aims to propose a complete and powerful methodology that allows the optimization of the passive suspension system of vehicles, which simultaneously takes comfort and safety into account and provides a set of optimal solutions through a Pareto-optimal front, in a low computational time.Design/methodology/approach: Unlike papers that consider simple vehicle models (quarter vehicle model or half car model) and/or simplified road profiles (harmonic excitation, for example) and/or perform a single-objective optimization and/or execute the dynamic analysis in the time domain, this paper presents an effective and fast methodology for the multi-objective optimization of the suspension system of a full-car model (including the driver seat) traveling on an irregular road profile, whose dynamic response is determined in the frequency domain, considerably reducing computational time.Findings: The results showed that there was a reduction of 28% in the driver seat vertical acceleration weighted root mean square (RMS) value of the proposed model, which is directly related to comfort, and, simultaneously, an improvement or constancy concerning safety, with low computational cost. Hence, the proposed methodology can be indicated as a successful tool for the optimal design of the suspension systems, considering, simultaneously, comfort and safety.Originality/value: Despite the extensive literature on optimizing vehicle passive suspension systems, papers combining multi-objective optimization presenting a Pareto-optimal front as a set of optimal results, a full-vehicle model (including the driver seat), an irregular road profile and the determination of the dynamic response in the frequency domain are not found.
- 13 August 2020
- Published by Springer Nature in Optimization and Engineering
- Vol. 22 (4) , 2707-2739
Multiscale topology optimization for frequency domain response with bi-material interpolation schemes
- 13 August 2020
- Published by Springer Nature in Optimization and Engineering
- Vol. 22 (4) , 2707-2739
Multiscale topology optimization for frequency domain response with bi-material interpolation schemes
- 19 July 2018
- Published by Springer Nature
- p. 141-153
Optimization of the Fundamental Frequency of Mechanical Structures by Using the Bidirectional Evolutionary Structural Method
- 19 July 2018
- Published by Springer Nature
- p. 141-153
Optimization of the Fundamental Frequency of Mechanical Structures by Using the Bidirectional Evolutionary Structural Method
- 11 March 2009
- Published by Taylor & Francis in Welding International
- Vol. 23 (3) , 166-172
Fracture toughness of CA6NM alloy, quenched and tempered, and of its welded joint without PWHT
CA6NM quenched and tempered steel is used in hydraulic turbine rotors, pumps and compressors. The objective of this research is to determine the fracture toughness of tempered and quenched CA6NM alloy, and of its welded joints without post-welded heat treatment (PWHT). To this end, compact tension (CT) test pieces are milled from pieces of CA6NM steel for evaluation of the toughness of the alloy used in a hydraulic turbine. Due to the elasto-plastic condition of the material, the test pieces are tested by means of the J integral concept, setting out the resistance curve J–R and the crack initiation J IC. In welded joints produced from ingots, without PWHT, the fragility they show does not allow the J–R curve for the CT test pieces to be drawn up, and the toughness is characterized by means of the K IC concept. The welding procedure looks at the probable conditions for repair of cavitation wear to the turbine, where PWHT cannot be carried out. The results confirmed the higher toughness for the CA6NM steel, with values approximately three times higher than those obtained in the welded joints without PWHT. In terms of the fracture, the CA6NM steel shows ductile behaviour while the welded joint without PWHT shows fragile behaviour.
- 11 March 2009
- Published by Taylor & Francis in Welding International
- Vol. 23 (3) , 166-172
Fracture toughness of CA6NM alloy, quenched and tempered, and of its welded joint without PWHT
CA6NM quenched and tempered steel is used in hydraulic turbine rotors, pumps and compressors. The objective of this research is to determine the fracture toughness of tempered and quenched CA6NM alloy, and of its welded joints without post-welded heat treatment (PWHT). To this end, compact tension (CT) test pieces are milled from pieces of CA6NM steel for evaluation of the toughness of the alloy used in a hydraulic turbine. Due to the elasto-plastic condition of the material, the test pieces are tested by means of the J integral concept, setting out the resistance curve J–R and the crack initiation J IC. In welded joints produced from ingots, without PWHT, the fragility they show does not allow the J–R curve for the CT test pieces to be drawn up, and the toughness is characterized by means of the K IC concept. The welding procedure looks at the probable conditions for repair of cavitation wear to the turbine, where PWHT cannot be carried out. The results confirmed the higher toughness for the CA6NM steel, with values approximately three times higher than those obtained in the welded joints without PWHT. In terms of the fracture, the CA6NM steel shows ductile behaviour while the welded joint without PWHT shows fragile behaviour.