VRVahideh Radmard

Vahideh Radmard

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vahideh Radmard has a total of 14 co-authors. Here are the top co-authors by number of shared publications:

  • Bahgat Sammakia

    Department of Mechanical Engineering, State University of New York at Binghamton, Binghamton, NY, USA

    3 shared publications
  • Cong Hiep Hoang

    Department of Mechanical Engineering, State University of New York at Binghamton, Binghamton, NY, USA

    3 shared publications
  • Najmeh Fallahtafti

    Department of Mechanical Engineering, State University of New York at Binghamton, Binghamton, NY, USA

    2 shared publications
  • Scott Schiffres

    Department of Mechanical Engineering, State University of New York at Binghamton, Binghamton, NY, USA

    2 shared publications
  • Yaser Hadad

    2 shared publications
  • Arad Azizi

    Department of Mechanical Engineering, State University of New York at Binghamton, Binghamton, NY, USA

    1 shared publication

Latest Publications

  • Design and Thermal Analysis of a 3-D Printed Impingement Pin Fin Cold Plate for Heterogeneous Integration Application

    by Cong Hiep Hoang, Arad Azizi, Najmeh Fallahtafti, Srikanth Rangarajan, Vahideh Radmard, Charles Arvin, Kamal Sikka, Scott Schiffres, Bahgat Sammakia

    Miniaturization high heat flux of power electronic devices have posed a colossal challenge for adequate thermal management. Conventional air-cooling solutions are inadequate for high-performance electronics. Liquid cooling is an alternative solution due to the higher specific heat and latent heat associated with the coolants. Liquid-cooled cold plates are typically manufactured by different approaches, such as skived, forged, extrusion, and electrical discharge machining. When researchers are facing challenges in creating complex geometries in small spaces, 3-D-printing can be a solution. In this article, a 3-D-printed cold plate was designed and characterized with water coolant. The printed metal fin structures were strong enough to undergo pressure from the fluid flow even at high flow rates and small fin structures. A copper block with the top surface area of 1 in $\times \,\,1$ in was used to mimic a computer chip. Experimental data have good match with a simulation model, which was built using commercial software 6SigmaET. Effects of geometry parameters and operating parameters were investigated. The fin diameter was varied from 0.3 to 0.5 mm and the fin height was maintained at 2 mm. A special manifold was designed to maximize the surface contact area between coolant and metal surface and therefore minimize thermal resistance. The flow rate was varied from 0.75 to 2 L/min and the coolant inlet temperature was varied from 25 °C to 48 °C. It was observed that for the coolant inlet temperature 25 °C and aluminum cold plate, the junction temperature was kept below 63.2 °C at an input power of 350 W and the pressure drop did not exceed 23 Kpa. Effects of metal materials used in 3-D-printing on the thermal performance of the cold plate were also studied in detail.


  • Hybrid microchannel/multi-jet two-phase heat sink: A benchmark and geometry optimization study of commercial product

    by Cong Hiep Hoang, Srikanth Rangarajan, Sadegh Khalili, Bharath Ramakrisnan, Vahideh Radmard, Yaser Hadad, Scott Schiffres, Bahgat Sammakia


  • Performance Analysis and Shape Optimization of an Impingement Microchannel Cold Plate

    by Yaser Hadad, Najmeh Fallahtafti, Leila Choobineh, Cong Hiep Hoang, Vahideh Radmard, Paul R. Chiarot, Bahgat Sammakia

    Optimization of liquid-cooled heatsinks (cold plates) is of critical importance due to their wide-spread application in high-performance electronic packages consisting of heterogeneous integrated systems, field programmable gate arrays (FPGAs), and on-chip hotspots. In this study, the thermo-hydraulic performance of a commercial microchannel impingement cold plate is analyzed in detail. Impingement cold plates are preferred over parallel flow cold plates due to their lower pressure drop where there is no restriction on space (i.e. where flow can enter perpendicular to the electronic board.). Splitting the flow into two branches cuts the flow rate and path in half, which leads to a lower pressure drop through the channels. Since the fins of the present commercial cold plate (considered as the baseline design) are tilted, the effect of fin tilt angle on the hydraulic and thermal performance of the cold plate is also studied. Response surface method is used to optimize the geometry of the fins and impinging inlet. The results of optimization show that hydraulic resistance can be reduced by 50% without a remarkable change in thermal resistance. The effect of geometric parameters on the cold plate thermo-hydraulic performance is studied by using the computational fluid dynamics results at response surface method design points. The variation of the cold plate coefficient of performance with the coolant flow rate and inlet temperature is compared for the baseline design and a selected optimal design. Finally, the effect of impinging inlet geometry on the chip temperature profile is also examined.