Meini Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Meini Wang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Min Tang
Shanghai Jiao Tong University
7 shared publications - Junfa Mao
Shanghai Jiao Tong University
6 shared publications - Yue Ping Zhang
Integrated Systems Research Laboratory, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
4 shared publications - Hao Chi Zhang
Institute of Electromagnetic Space and the State Key Laboratory of Millimeter Waves, Southeast University, Nanjing, China
3 shared publications - Le Peng Zhang
State Key Laboratory of Millimeter Waves, Southeast University, Nanjing, China
2 shared publications - Tie Jun Cui
State Key Laboratory of Millimeter Waves Southeast University Nanjing China
2 shared publications
Latest Publications
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (12) , 4633-4637
Isosceles-Right-Triangular SIW-Fed Dual-Polarized Filtering DRA With High Port Isolation
A differential dual-polarized filtering dielectric resonator antenna (DRA) fed by isosceles-right-triangular substrate integrated waveguides (IRTSIWs) is presented in this letter. The out-of-phase TE110 modes of the IRTSIWs excite orthogonal modes in the DRA, resulting in the co-frequency dual-polarization. High isolation between the differential-fed ports is realized with the use of IRTSIW cavities. Then, a bandpass filtering response is realized using the coupling topology. The radiation nulls are introduced at the passband edges to improve frequency selectivity. For demonstration, a prototype is designed and fabricated. The measured results show that the impedance bandwidth is 5.15-5.60 GHz, the gain in the passband is no less than 6 dBi, and the out-of-band suppression is higher than 16 dB. Besides, a high port isolation of more than 78 dB is achieved in the proposed design.
- 17 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (12) , 4633-4637
Isosceles-Right-Triangular SIW-Fed Dual-Polarized Filtering DRA With High Port Isolation
A differential dual-polarized filtering dielectric resonator antenna (DRA) fed by isosceles-right-triangular substrate integrated waveguides (IRTSIWs) is presented in this letter. The out-of-phase TE110 modes of the IRTSIWs excite orthogonal modes in the DRA, resulting in the co-frequency dual-polarization. High isolation between the differential-fed ports is realized with the use of IRTSIW cavities. Then, a bandpass filtering response is realized using the coupling topology. The radiation nulls are introduced at the passband edges to improve frequency selectivity. For demonstration, a prototype is designed and fabricated. The measured results show that the impedance bandwidth is 5.15-5.60 GHz, the gain in the passband is no less than 6 dBi, and the out-of-band suppression is higher than 16 dB. Besides, a high port isolation of more than 78 dB is achieved in the proposed design.
- 25 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 8076-8081
Miniaturization and Decoupling of Wideband Stacked Patch Antennas Based on Spoof Surface Plasmon Polaritons
The miniaturization and decoupling of wideband stacked patch antennas is first presented in this communication. The miniaturization is achieved by loading spoof surface plasmon polariton (SSPP) structures on non-radiation edges of the stacked patches. Meanwhile, the wideband operation is realized by controlling the difference in propagation constants of the stacked patches. Due to the large propagation constant of the SSPP structures, the size of the antenna is reduced to 0.18 × 0.18 λ 0 2 , which achieves 72% footprint-reduction as compared with the conventional patch antennas on the same substrates. Moreover, both the simulation and measurement show that the proposed miniaturized antenna exhibits a wide bandwidth of more than 16%. To explore its applications in compact multi-input-multi-output (MIMO) systems, a miniaturized wideband decoupling scheme is further proposed by introducing a coupling null at the lower resonant frequency using an SSPP-loaded defected ground structure (DGS). Experimental results show that high isolation larger than 20 dB is achieved over the wide bandwidth with a center-to-center spacing of 0.28 λ 0 .
- 25 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (10) , 8076-8081
Miniaturization and Decoupling of Wideband Stacked Patch Antennas Based on Spoof Surface Plasmon Polaritons
The miniaturization and decoupling of wideband stacked patch antennas is first presented in this communication. The miniaturization is achieved by loading spoof surface plasmon polariton (SSPP) structures on non-radiation edges of the stacked patches. Meanwhile, the wideband operation is realized by controlling the difference in propagation constants of the stacked patches. Due to the large propagation constant of the SSPP structures, the size of the antenna is reduced to 0.18 × 0.18 λ 0 2 , which achieves 72% footprint-reduction as compared with the conventional patch antennas on the same substrates. Moreover, both the simulation and measurement show that the proposed miniaturized antenna exhibits a wide bandwidth of more than 16%. To explore its applications in compact multi-input-multi-output (MIMO) systems, a miniaturized wideband decoupling scheme is further proposed by introducing a coupling null at the lower resonant frequency using an SSPP-loaded defected ground structure (DGS). Experimental results show that high isolation larger than 20 dB is achieved over the wide bandwidth with a center-to-center spacing of 0.28 λ 0 .
- 22 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (2) , 1449-1458
Miniaturized Laminated Resonator Antenna Array Loaded With Periodic Irises in LTCC
A miniaturized laminated resonator antenna (LRA) array with periodic irises is proposed in this paper. By means of the distinguished slow-wave property of the periodic iris-loaded waveguide (IWG), a compact LRA element with a dimension of only 0.36 λ 0 × 0.26 λ 0 × 0.08 λ 0 is designed, where λ 0 is the wavelength in the free space at 60 GHz. The small transverse size makes it possible to construct an antenna array with the element spacing of less than 0.5 λ 0 , which is rather beneficial to the scanning arrays and multiple-input multiple-output (MIMO) systems. For demonstration, a series-fed 1×6 antenna array in E-plane with the element spacing of 0.38 λ 0 is designed and fabricated with the low temperature co-fired ceramic (LTCC) process. The measured relative impedance bandwidth is 9.2 % (from 56.3 GHz to 61.8 GHz). The measured peak gain and 3-dB gain bandwidth are 10.6 dBi and 5.3 GHz, respectively. Furthermore, the scanning arrays are fabricated to demonstrate the scanning performance, with an element spacing of 0.45 λ 0 in H-plane. They support a measured maximum scanning angle of 43° while the gain drop is within 2.5 dB.
- 22 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (2) , 1449-1458
Miniaturized Laminated Resonator Antenna Array Loaded With Periodic Irises in LTCC
A miniaturized laminated resonator antenna (LRA) array with periodic irises is proposed in this paper. By means of the distinguished slow-wave property of the periodic iris-loaded waveguide (IWG), a compact LRA element with a dimension of only 0.36 λ 0 × 0.26 λ 0 × 0.08 λ 0 is designed, where λ 0 is the wavelength in the free space at 60 GHz. The small transverse size makes it possible to construct an antenna array with the element spacing of less than 0.5 λ 0 , which is rather beneficial to the scanning arrays and multiple-input multiple-output (MIMO) systems. For demonstration, a series-fed 1×6 antenna array in E-plane with the element spacing of 0.38 λ 0 is designed and fabricated with the low temperature co-fired ceramic (LTCC) process. The measured relative impedance bandwidth is 9.2 % (from 56.3 GHz to 61.8 GHz). The measured peak gain and 3-dB gain bandwidth are 10.6 dBi and 5.3 GHz, respectively. Furthermore, the scanning arrays are fabricated to demonstrate the scanning performance, with an element spacing of 0.45 λ 0 in H-plane. They support a measured maximum scanning angle of 43° while the gain drop is within 2.5 dB.
- 14 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (3) , 1050-1054
Design of Miniaturized Low Cross-Polarization Quarter-Wave Patch Antennas Using Gradient Spoof Surface Plasmon Polaritons
A quarter-wave patch antenna (QWPA) suffers from the fundamental disadvantage of a high cross-polarization level (XPL) in the H -plane. In this letter, we present a new method to overcome this issue by integrating a gradient spoof surface plasmon polariton (SSPP) structure on the side edges of QWPAs. In the proposed scheme, the SSPP structure is gradient loaded from the open end to the short end to suppress the cross-polarization radiation from the side edges. Both the single-ended and differentially-driven QWPAs are investigated and compared based on the proposed method. Simulated results indicate that SSPP-loaded QWPAs exhibit remarkable miniaturization and XPL reduction as compared with the conventional ones. To validate the feasibility of the proposed method, a differential prototype is fabricated and measured. Experimental results show that the proposed antenna achieves a distinct cross-polarization reduction of over 20 dB and a compact size of 0.088 × 0.095 λ0 2 at the center operating frequency.
- 14 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (3) , 1050-1054
Design of Miniaturized Low Cross-Polarization Quarter-Wave Patch Antennas Using Gradient Spoof Surface Plasmon Polaritons
A quarter-wave patch antenna (QWPA) suffers from the fundamental disadvantage of a high cross-polarization level (XPL) in the H -plane. In this letter, we present a new method to overcome this issue by integrating a gradient spoof surface plasmon polariton (SSPP) structure on the side edges of QWPAs. In the proposed scheme, the SSPP structure is gradient loaded from the open end to the short end to suppress the cross-polarization radiation from the side edges. Both the single-ended and differentially-driven QWPAs are investigated and compared based on the proposed method. Simulated results indicate that SSPP-loaded QWPAs exhibit remarkable miniaturization and XPL reduction as compared with the conventional ones. To validate the feasibility of the proposed method, a differential prototype is fabricated and measured. Experimental results show that the proposed antenna achieves a distinct cross-polarization reduction of over 20 dB and a compact size of 0.088 × 0.095 λ0 2 at the center operating frequency.
- 24 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (2) , 539-545
Energy Selective Antenna: Concept, Design, and Experiment
In this article, a novel concept of energy selective antenna (ESA) is presented for integrating the functions of the common antenna and the adaptive high-power electromagnetic protection. To demonstrate this concept, a typical structure based on the microstrip patch antenna loaded with limiting PIN diodes is designed. It behaves as a normal antenna under the low-power incidence with the off -status of PIN diodes but rejects the signal in the interested frequency band when the PIN diodes are triggered by the high-power electromagnetic waves. An equivalent circuit is presented to illustrate the operation principle and the parametric studies are carried out to investigate the effects of several key factors on the proposed ESA. Furthermore, a prototype is fabricated and the measured results indicate that the antenna has excellent bandwidth and radiation performance in the normal working state, while performing a good isolation of more than 25 dB in the protection state.
- 24 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (2) , 539-545
Energy Selective Antenna: Concept, Design, and Experiment
In this article, a novel concept of energy selective antenna (ESA) is presented for integrating the functions of the common antenna and the adaptive high-power electromagnetic protection. To demonstrate this concept, a typical structure based on the microstrip patch antenna loaded with limiting PIN diodes is designed. It behaves as a normal antenna under the low-power incidence with the off -status of PIN diodes but rejects the signal in the interested frequency band when the PIN diodes are triggered by the high-power electromagnetic waves. An equivalent circuit is presented to illustrate the operation principle and the parametric studies are carried out to investigate the effects of several key factors on the proposed ESA. Furthermore, a prototype is fabricated and the measured results indicate that the antenna has excellent bandwidth and radiation performance in the normal working state, while performing a good isolation of more than 25 dB in the protection state.
- 5 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (11) , 7889-7894
Miniaturization of Frequency-Reconfigurable Antenna Using Periodic Slow-Wave Structure
A challenge for frequency-reconfigurable antennas is how to realize miniaturized structures while preserving satisfying radiation performance in whole operation bandwidth. To address this problem, we apply planar periodic slow-wave structure (PSWS) with controlled dispersion features for miniaturization of antenna. Due to the subwavelength property and large propagation constant, this design holds a much more compact size than conventional microstrip structures. The proposed antenna consists of a double-layered dielectric substrate with the tunable patch on the top and a bias network combining with the feeding part on the bottom. The operating frequency is electronically controlled by the varactors shortened to the ground on nonradiating edges. It ranges from 4.87 to 5.52 GHz when the bias voltage varies from 9 to 16 V. Both simulated and measured results show that the proposed antenna maintains acceptable gains and similar radiation patterns while shrinking the size effectively. The proposed miniaturized and frequency-reconfigurable antenna holds potential applications in the ultracompact frequency hopping communication systems.
- 5 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 69 (11) , 7889-7894
Miniaturization of Frequency-Reconfigurable Antenna Using Periodic Slow-Wave Structure
A challenge for frequency-reconfigurable antennas is how to realize miniaturized structures while preserving satisfying radiation performance in whole operation bandwidth. To address this problem, we apply planar periodic slow-wave structure (PSWS) with controlled dispersion features for miniaturization of antenna. Due to the subwavelength property and large propagation constant, this design holds a much more compact size than conventional microstrip structures. The proposed antenna consists of a double-layered dielectric substrate with the tunable patch on the top and a bias network combining with the feeding part on the bottom. The operating frequency is electronically controlled by the varactors shortened to the ground on nonradiating edges. It ranges from 4.87 to 5.52 GHz when the bias voltage varies from 9 to 16 V. Both simulated and measured results show that the proposed antenna maintains acceptable gains and similar radiation patterns while shrinking the size effectively. The proposed miniaturized and frequency-reconfigurable antenna holds potential applications in the ultracompact frequency hopping communication systems.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 10 (8) , 1367-1374
Crosstalk Noise Suppression Between Single and Differential Transmission Lines Using Spoof Surface Plasmon Polaritons
Crosstalk noise suppression is a crux in high-speed integrated circuit design, which requires weak coupling between transmission lines over a wide band. To overcome the difficulty, this paper presents a novel method to suppress the broadband crosstalk noise between a single transmission line (TL) and the differential pair based on spoof surface plasmon polaritons (SPPs). Due to the subwavelength feature of spoof SPP TLs, a natural mode mismatching between the spoof SPP TL and conventional microstrip (MS) brings a broadband suppression of near-field coupling. In order to verify the crosstalk suppression effect, four different kinds of prototypes are discussed and compared. The simulated and measured results in the frequency domain and time domain demonstrate that the proposed scheme achieves more than 83% far-end noise peak suppression than the traditional MS technology by replacing the single MS TL to the spoof SPP TL. Accordingly, the time-domain crosstalk noise is significantly suppressed without any extra costs, demonstrating its potential applications in ultra-compact high-speed integrated circuits.
- 24 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 10 (8) , 1367-1374
Crosstalk Noise Suppression Between Single and Differential Transmission Lines Using Spoof Surface Plasmon Polaritons
Crosstalk noise suppression is a crux in high-speed integrated circuit design, which requires weak coupling between transmission lines over a wide band. To overcome the difficulty, this paper presents a novel method to suppress the broadband crosstalk noise between a single transmission line (TL) and the differential pair based on spoof surface plasmon polaritons (SPPs). Due to the subwavelength feature of spoof SPP TLs, a natural mode mismatching between the spoof SPP TL and conventional microstrip (MS) brings a broadband suppression of near-field coupling. In order to verify the crosstalk suppression effect, four different kinds of prototypes are discussed and compared. The simulated and measured results in the frequency domain and time domain demonstrate that the proposed scheme achieves more than 83% far-end noise peak suppression than the traditional MS technology by replacing the single MS TL to the spoof SPP TL. Accordingly, the time-domain crosstalk noise is significantly suppressed without any extra costs, demonstrating its potential applications in ultra-compact high-speed integrated circuits.