Jaebum Sung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jaebum Sung has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Hongyun So
Hanyang University
6 shared publications Baek-Il Bae
1 shared publicationByeongjo Ko
School of Mechanical Engineering, Hanyang University, Seoul, South Korea
1 shared publicationChang-Sik Choi
1 shared publicationDong-Hee Son
1 shared publication- Dongsun Hwangbo1 shared publication
Latest Publications
- 20 January 2025
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 429
Chemical-responsive curved actuator using PDMS/Ecoflex composite bilayer for rapid detection of chemical solvent leakage
- 20 January 2025
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 429
Chemical-responsive curved actuator using PDMS/Ecoflex composite bilayer for rapid detection of chemical solvent leakage
- Open Access
- 10 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 749-757
Fabrication of functional surfaces using layer height method in material extrusion type 3D printing
- 10 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 749-757
Open AccessFabrication of functional surfaces using layer height method in material extrusion type 3D printing
- Open Access
- 7 June 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 18
Effect of nanomaterials (carbon nanotubes, nano-silica, graphene oxide) on bond behavior between concrete and reinforcing bars
- 7 June 2023
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 18
Open AccessEffect of nanomaterials (carbon nanotubes, nano-silica, graphene oxide) on bond behavior between concrete and reinforcing bars
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (15) , 16403-16408
Cube-Shaped GaN UV Photodetectors Using 3D-Printed Panels for Omnidirectional Detection
In this study, we designed and developed a hexahedral ultraviolet (UV) photodetector using three-dimensional (3D) printing. Furthermore, we demonstrated the proposed photodetector's functionality (omnidirectional UV detection) using photosensitive gallium nitride (GaN). To fabricate the cube (regular hexahedron), six panels were separately 3D-printed; a GaN UV photodetector was then mounted onto each panel during assembly. Given that the hexahedral photodetector had six sensors, the change in current for each sensor was distinct based on the angle of incidence of UV light; consequently, the UV source could be easily traced. Compared to conventional solar sensors, the proposed novel photodetector could estimate the various locations of the UV source through selective activation and deactivation. Optical and electrical characterization revealed high absorption of the UV spectra (near 370 nm), high signal-to-noise values (47-70), and rapid response times (0.4-0.8 s). This study demonstrates the feasibility of the design and fabrication-using 3D printing technology-of optical sensors for the multiple detection of incident UV light during navigation in various environments such as outer space, oceans, and subterranean environments.
- 14 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (15) , 16403-16408
Cube-Shaped GaN UV Photodetectors Using 3D-Printed Panels for Omnidirectional Detection
In this study, we designed and developed a hexahedral ultraviolet (UV) photodetector using three-dimensional (3D) printing. Furthermore, we demonstrated the proposed photodetector's functionality (omnidirectional UV detection) using photosensitive gallium nitride (GaN). To fabricate the cube (regular hexahedron), six panels were separately 3D-printed; a GaN UV photodetector was then mounted onto each panel during assembly. Given that the hexahedral photodetector had six sensors, the change in current for each sensor was distinct based on the angle of incidence of UV light; consequently, the UV source could be easily traced. Compared to conventional solar sensors, the proposed novel photodetector could estimate the various locations of the UV source through selective activation and deactivation. Optical and electrical characterization revealed high absorption of the UV spectra (near 370 nm), high signal-to-noise values (47-70), and rapid response times (0.4-0.8 s). This study demonstrates the feasibility of the design and fabrication-using 3D printing technology-of optical sensors for the multiple detection of incident UV light during navigation in various environments such as outer space, oceans, and subterranean environments.
- 1 April 2021
- Published by Elsevier in Surfaces and Interfaces
- Vol. 23
3D printing-assisted fabrication of microgrid patterns for flexible antiadhesive polymer surfaces
- 1 April 2021
- Published by Elsevier in Surfaces and Interfaces
- Vol. 23
3D printing-assisted fabrication of microgrid patterns for flexible antiadhesive polymer surfaces
- 18 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (18) , 11007-11013
Direct and Continuous Liquid-Level Sensing Using Gallium Nitride Ultraviolet Photodetectors
A liquid-level sensor using a gallium nitride (GaN) ultraviolet (UV) photodetector was successfully demonstrated. As the liquid level was changed, the intensity of UV light on the GaN surface was varied owing to the refraction of light on the liquid surface. For the fabrication of the liquid-level sensor, facile and rapid manufacturing was employed, involving metal wire bonding on the semiconductor surface. To characterize the fabricated sensor, the water level in the cylinder was measured according to the photocurrent change of the GaN UV photodetector. The responsivity of the liquid-level sensor depended on the diameter of the cylinder, applied voltage, and emission angle of the UV source. In particular, a cylinder diameter of 16 cm and an emission angle of 45° yielded a resolution of 0.05 cm up to the water level of 10 cm. The results of this study confirm the feasibility of liquid-level sensors for continuous and simultaneous liquid-level monitoring in harsh environments, including high-temperature plants, nuclear reactors, and chemical tanks.
- 18 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (18) , 11007-11013
Direct and Continuous Liquid-Level Sensing Using Gallium Nitride Ultraviolet Photodetectors
A liquid-level sensor using a gallium nitride (GaN) ultraviolet (UV) photodetector was successfully demonstrated. As the liquid level was changed, the intensity of UV light on the GaN surface was varied owing to the refraction of light on the liquid surface. For the fabrication of the liquid-level sensor, facile and rapid manufacturing was employed, involving metal wire bonding on the semiconductor surface. To characterize the fabricated sensor, the water level in the cylinder was measured according to the photocurrent change of the GaN UV photodetector. The responsivity of the liquid-level sensor depended on the diameter of the cylinder, applied voltage, and emission angle of the UV source. In particular, a cylinder diameter of 16 cm and an emission angle of 45° yielded a resolution of 0.05 cm up to the water level of 10 cm. The results of this study confirm the feasibility of liquid-level sensors for continuous and simultaneous liquid-level monitoring in harsh environments, including high-temperature plants, nuclear reactors, and chemical tanks.