Muhammad Shoaib Karam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammad Shoaib Karam has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Hikaru Nakamura
1 shared publication- Hikaru Nakamura
Department of Civil and Environmental Engineering, Nagoya University, Furo-Cho, Chikusa-Ku, Nagoya 464-8603, Japan
1 shared publication Taito Miura
1 shared publication- Taito Miura
Department of Civil and Environmental Engineering, Nagoya University, Furo-Cho, Chikusa-Ku, Nagoya 464-8603, Japan
1 shared publication Yoshihito Yamamoto
1 shared publication- Yoshihito Yamamoto
Department of Civil and Environmental Engineering Hosei University Tokyo Japan
1 shared publication
Latest Publications
- Open Access
Numerical Evaluation of the Perfobond (PBL) Shear Connector Subjected to Lateral Pressure Using Coupled Rigid Body Spring Model (RBSM) and Nonlinear Solid Finite Element Method (FEM)
An analytical investigation focusing on the concrete damage progress of the PBL shear connector under the influence of various lateral pressures, employing a coupled RBSM and solid FEM model was carried out. The analytical model succeeded in simulating the test shear capacities and the failure modes adequately. The internal failure process was also clarified; the two horizontal cracks occurred near the top of the concrete dowels through the hole of the perforated steel plate, and afterward, the two vertical cracks also initiated and propagated along with the shear surface. In a low lateral pressure case, the shear strength was determined by the vertical cracks propagated along the shear surface. While as the amount of applied lateral pressure increased, the shear strength of the two vertical cracked surfaces was enhanced, and the shear strength of the PBL was characterized by the occurrence of the splitting cracks and caused the splitting failure into the side concrete blocks. Moreover, the combined effects of lateral pressure and hole diameters were also evaluated numerically, and it was found that the increase in shear strength was more in a large diameter case subjected to high lateral pressure because of the wide compressive regions generated around the concrete dowel.
Open AccessNumerical Evaluation of the Perfobond (PBL) Shear Connector Subjected to Lateral Pressure Using Coupled Rigid Body Spring Model (RBSM) and Nonlinear Solid Finite Element Method (FEM)
An analytical investigation focusing on the concrete damage progress of the PBL shear connector under the influence of various lateral pressures, employing a coupled RBSM and solid FEM model was carried out. The analytical model succeeded in simulating the test shear capacities and the failure modes adequately. The internal failure process was also clarified; the two horizontal cracks occurred near the top of the concrete dowels through the hole of the perforated steel plate, and afterward, the two vertical cracks also initiated and propagated along with the shear surface. In a low lateral pressure case, the shear strength was determined by the vertical cracks propagated along the shear surface. While as the amount of applied lateral pressure increased, the shear strength of the two vertical cracked surfaces was enhanced, and the shear strength of the PBL was characterized by the occurrence of the splitting cracks and caused the splitting failure into the side concrete blocks. Moreover, the combined effects of lateral pressure and hole diameters were also evaluated numerically, and it was found that the increase in shear strength was more in a large diameter case subjected to high lateral pressure because of the wide compressive regions generated around the concrete dowel.
- 28 June 2019
- Published by International Association for Fracture Mechanics of Concrete and Concrete Structures
MESOSCALE ANALYSIS FOR THE BOND BEHAVIOR OF CONCRETE UNDER ACTIVE CONFINEMENT USING COUPLED RBSM AND SOLID FEM
The research manuscript deals with the brief introduction to the development and the validation of the new coupled numerical formulation, comprised of the Rigid Body Spring Model (RBSM) and the solid Finite Element Method (FEM) evaluating the bond behavior and failure mechanism of the actively confined and unconfined RC specimens loaded under pull-out test. The RBSM has been referred as an effective numerical framework for the evaluation of nonlinear mechanical response of concrete, quantitatively. However, the modeling of the reinforcing steel in RBSM has difficulty for simulating the complex behavior of steel such as elastoplasticity. Therefore, this limitation refers towards the development of new numerical formulation, i.e., coupled RBSM-FEM. In coupled RBSM-FEM, steel embedded in concrete is modeled using eight noded nonlinear solid finite elements considering the actual geometrical features e.g., rib height, shape and lug spacing, etc. In the coupled numerical formulation, concrete is modeled using RBSM. The boundary interfaces between concrete and steel (Solid FEM) has been accomplished through link element. The link element on the interface between RBSM element and solid FEM element consists of two shear springs and one normal spring. The proposed model is validated through the experimental investigations on RC specimens loaded under pull-out test with and without externally applied normal pressure. The proposed model has capability to simulate the internal fracture mechanism of concrete and elastoplastic behavior of the steel.
- 28 June 2019
- Published by International Association for Fracture Mechanics of Concrete and Concrete Structures
MESOSCALE ANALYSIS FOR THE BOND BEHAVIOR OF CONCRETE UNDER ACTIVE CONFINEMENT USING COUPLED RBSM AND SOLID FEM
The research manuscript deals with the brief introduction to the development and the validation of the new coupled numerical formulation, comprised of the Rigid Body Spring Model (RBSM) and the solid Finite Element Method (FEM) evaluating the bond behavior and failure mechanism of the actively confined and unconfined RC specimens loaded under pull-out test. The RBSM has been referred as an effective numerical framework for the evaluation of nonlinear mechanical response of concrete, quantitatively. However, the modeling of the reinforcing steel in RBSM has difficulty for simulating the complex behavior of steel such as elastoplasticity. Therefore, this limitation refers towards the development of new numerical formulation, i.e., coupled RBSM-FEM. In coupled RBSM-FEM, steel embedded in concrete is modeled using eight noded nonlinear solid finite elements considering the actual geometrical features e.g., rib height, shape and lug spacing, etc. In the coupled numerical formulation, concrete is modeled using RBSM. The boundary interfaces between concrete and steel (Solid FEM) has been accomplished through link element. The link element on the interface between RBSM element and solid FEM element consists of two shear springs and one normal spring. The proposed model is validated through the experimental investigations on RC specimens loaded under pull-out test with and without externally applied normal pressure. The proposed model has capability to simulate the internal fracture mechanism of concrete and elastoplastic behavior of the steel.