Babak Bonakdarpour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Babak Bonakdarpour has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Elham Abdollahzadeh Sharghi
Environmental Group, Department of Energy, Materials and Energy Research Center, Karaj, Iran
5 shared publications B. Nasernejad
Chemical Engineering Department, Amirkabir University of Technology, 424 Hafez Ave., Tehran, Iran
4 shared publicationsMohammad Reza Mehrnia
School of Chemical Engineering, University College of Engineering, University of Tehran, Tehran, Iran
4 shared publications- Yousef Rashidi
Environmental Sciences Research Institute, Shahid Beheshti University, Tehran, Iran
4 shared publications - Davoud Fatmehsari Haghshenas
Department of Materials and Metallurgical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
3 shared publications - Eskandar Keshavarz Alamdari
Department of Materials and Metallurgical Engineering, Amirkabir University of Technology, Tehran, Iran
3 shared publications
Latest Publications
- 25 November 2024
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 48 (2) , 233-245
Enhancing the anaerobic sludge characteristics and inorganic impurities removal from synthesis wastewater through integration of electrocoagulation process with up-flow anaerobic sludge blanket reactor
The present study investigated effects of coupling electrocoagulation (EC) process with an anaerobic digestion bioreactor, namely up-flow anaerobic sludge blanket (UASB), for the synthetic wastewater treatment. The EC-UASB mode of operation consisted of one anode and two cathodes subjected to an intermittent electrical current (10 min ON/30 min OFF) with current density of 1.5 mA/cm2. In light of this integration, the concentration of mixed liquor suspended solids and mixed liquor volatile suspended solids within anaerobic granular sludge (AGS) increased by 20.0 ± 1.4% and 12.8 ± 0.8%, respectively. The results of sludge volume index, loosely and tightly bound extracellular polymeric substances and their constituents (protein and carbohydrate) revealed that through this integration the quality of AGS has been improved. Furthermore, results of scanning electron microscopy and Fourier-transform infrared spectroscopy showed alteration in the morphology and functional groups of AGS, respectively. Additionally, this combination has demonstrated promising results in terms of performance improvement by increasing the removal efficiency of total dissolved solids by 12.1 ± 0.3% and reducing the ionic pollution in treated wastewater. However, the integration of the EC system within the UASB resulted in energy consumption and operating cost of 1.33 kWh/m3 and 0.099 USD/m3, respectively.
- 25 November 2024
- Published by Springer Nature in Bioprocess and Biosystems Engineering
- Vol. 48 (2) , 233-245
Enhancing the anaerobic sludge characteristics and inorganic impurities removal from synthesis wastewater through integration of electrocoagulation process with up-flow anaerobic sludge blanket reactor
The present study investigated effects of coupling electrocoagulation (EC) process with an anaerobic digestion bioreactor, namely up-flow anaerobic sludge blanket (UASB), for the synthetic wastewater treatment. The EC-UASB mode of operation consisted of one anode and two cathodes subjected to an intermittent electrical current (10 min ON/30 min OFF) with current density of 1.5 mA/cm2. In light of this integration, the concentration of mixed liquor suspended solids and mixed liquor volatile suspended solids within anaerobic granular sludge (AGS) increased by 20.0 ± 1.4% and 12.8 ± 0.8%, respectively. The results of sludge volume index, loosely and tightly bound extracellular polymeric substances and their constituents (protein and carbohydrate) revealed that through this integration the quality of AGS has been improved. Furthermore, results of scanning electron microscopy and Fourier-transform infrared spectroscopy showed alteration in the morphology and functional groups of AGS, respectively. Additionally, this combination has demonstrated promising results in terms of performance improvement by increasing the removal efficiency of total dissolved solids by 12.1 ± 0.3% and reducing the ionic pollution in treated wastewater. However, the integration of the EC system within the UASB resulted in energy consumption and operating cost of 1.33 kWh/m3 and 0.099 USD/m3, respectively.
- Open Access
- 18 November 2024
- Published by MDPI AG in Chemengineering
- Vol. 8 (6) , 117
Data-Driven Gas Holdup Correlation in Bubble Column Reactors Considering Alcohol Concentration and Carbon Number
Due to the complex relationship between various parameters affecting gas holdup in bubble column reactors, a unique correlation for gas holdup does not exist. The available correlations proposed in the literature for gas holdup prediction in aqueous alcohol solutions in bubble columns fail to predict gas holdup over a wide range of conditions. Therefore, based on around 1000 data points from the previous studies, an empirical correlation and a trained model were derived using the dimensionless numbers Reynolds, Froude, Eötvös to Morton ratio, and alcohol carbon number. The predictions were compared to experiments with different water–alcohol mediums at various concentrations to validate the correlation and trained model, and a good agreement was observed. However, the ML model was predicting more accurately, and it was indicated that the Reynolds number had the most significant impact on gas holdup, followed by the Eötvös to Morton ratio.
- 18 November 2024
- Published by MDPI AG in Chemengineering
- Vol. 8 (6) , 117
Open AccessData-Driven Gas Holdup Correlation in Bubble Column Reactors Considering Alcohol Concentration and Carbon Number
Due to the complex relationship between various parameters affecting gas holdup in bubble column reactors, a unique correlation for gas holdup does not exist. The available correlations proposed in the literature for gas holdup prediction in aqueous alcohol solutions in bubble columns fail to predict gas holdup over a wide range of conditions. Therefore, based on around 1000 data points from the previous studies, an empirical correlation and a trained model were derived using the dimensionless numbers Reynolds, Froude, Eötvös to Morton ratio, and alcohol carbon number. The predictions were compared to experiments with different water–alcohol mediums at various concentrations to validate the correlation and trained model, and a good agreement was observed. However, the ML model was predicting more accurately, and it was indicated that the Reynolds number had the most significant impact on gas holdup, followed by the Eötvös to Morton ratio.
- 13 March 2024
- Published by Elsevier in Chemosphere
- Vol. 354, 141716
How high salt shock affects performance and membrane fouling characteristics of a halophilic membrane bioreactor used for treating hypersaline wastewater
- 13 March 2024
- Published by Elsevier in Chemosphere
- Vol. 354, 141716
How high salt shock affects performance and membrane fouling characteristics of a halophilic membrane bioreactor used for treating hypersaline wastewater
- 23 May 2022
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 8 (7) , 1561-1578
The application of membrane sequencing batch reactors in high rate activated sludge processes: the effect of the organic loading rate on the bioflocculation and fouling phenomenon
In the current study, for the first time a membrane sequencing batch reactor (MSBR) was assessed for use in a high rate activated sludge process (HRAS). For this purpose, the effect of the organic loading rate (OLR), an important operating parameter in a HRAS process, at four levels, in the range of 4–16 kg COD m−3 d−1, on the chemical oxygen demand (COD) and energy recovery performance and membrane fouling characteristics of a high loaded (HL) MSBR (i.e. one operated under HRAS conditions) was investigated. With the increase in OLR from 4 to 16 kg COD m−3 d−1, the COD recovery reached a maximum value of 84%, which was significantly better than previously reported values for non-membrane-based bioreactors. Also, a total energy recovery of 0.25 g COD CH4 per g CODinf was achieved for the waste activated sludge (WAS) stream produced under the HL-MSBR operating conditions. The highest OLR, however, also yielded the highest rate of membrane fouling, and the principal membrane fouling mechanism was found to be the cake layer formation at all OLRs. The soluble microbial products (especially their protein fraction) were identified as the major contributing factor to fouling in the HL-MSBR. Based on these findings, the use of membrane relaxation and the addition of FeCl3 were proposed as the membrane fouling control strategies during the use of the HL-MSBR in HRAS processes. However, a comprehensive economic assessment of the HL-MSBR for such use necessitates the optimization of the SRT as well as the experimental investigation of the proposed fouling control strategies.
- 23 May 2022
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 8 (7) , 1561-1578
The application of membrane sequencing batch reactors in high rate activated sludge processes: the effect of the organic loading rate on the bioflocculation and fouling phenomenon
In the current study, for the first time a membrane sequencing batch reactor (MSBR) was assessed for use in a high rate activated sludge process (HRAS). For this purpose, the effect of the organic loading rate (OLR), an important operating parameter in a HRAS process, at four levels, in the range of 4–16 kg COD m−3 d−1, on the chemical oxygen demand (COD) and energy recovery performance and membrane fouling characteristics of a high loaded (HL) MSBR (i.e. one operated under HRAS conditions) was investigated. With the increase in OLR from 4 to 16 kg COD m−3 d−1, the COD recovery reached a maximum value of 84%, which was significantly better than previously reported values for non-membrane-based bioreactors. Also, a total energy recovery of 0.25 g COD CH4 per g CODinf was achieved for the waste activated sludge (WAS) stream produced under the HL-MSBR operating conditions. The highest OLR, however, also yielded the highest rate of membrane fouling, and the principal membrane fouling mechanism was found to be the cake layer formation at all OLRs. The soluble microbial products (especially their protein fraction) were identified as the major contributing factor to fouling in the HL-MSBR. Based on these findings, the use of membrane relaxation and the addition of FeCl3 were proposed as the membrane fouling control strategies during the use of the HL-MSBR in HRAS processes. However, a comprehensive economic assessment of the HL-MSBR for such use necessitates the optimization of the SRT as well as the experimental investigation of the proposed fouling control strategies.
- 21 August 2020
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 96 (2) , 404-411
Fouling identification in reciprocal membrane photobioreactor (RMPBR) containing Chlorella vulgaris species: Hydraulic resistances assessment
BACKGROUND: The membrane photobioreactor is a combination of membrane technology and the photobioreactor system. It is an economic and efficient system for microalgae cultivation. Light cycles and its intensity are significant parameters in the biomass production and synthesis of metabolites, such as protein and carbohydrates, within the microalgae cells. These parameters can, therefore, have a significant impact on the rate and characteristics of fouling in membrane photobioreactor systems.RESULTS: In this work, Chlorella vulgaris (green microalgae) was cultivated within the designed reciprocal membrane photobioreactor (RMPBR) under 24–0, 16–8, and 12–12 light–dark (L/D) cycles. Also, the transmembrane pressure (TMP) and different hydraulic membrane resistances (cake layer, pore‐blocking, and fluid resistances) were investigated. The 16–8 L/D cycle had the fastest fouling time (96 h), highest pore‐blocking resistance (Rp), and the maximum concentrations of protein and carbohydrate in the supernatant and permeate flux. However, the 12–12 L/D recorded the maximum cake layer resistance (Rc), the highest content of protein within the cake layer, and the longest fouling time (226 h). Additionally, the highest carbohydrate concentration within the cake layer was for the 24–0 L/D regime, and it was fouled after 162 h.CONCLUSION: The Rc for each cycle had the highest values compared to the other calculated resistances. When the membrane is fouled, the mechanical membrane cleaning method employed in the RMPBR, which is in the form of an automatic spongy blade, cleans the cake layer on the membrane and improves its operation up to 80% via decreasing the Rt of the system. © 2020 Society of Chemical Industry (SCI)
- 21 August 2020
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 96 (2) , 404-411
Fouling identification in reciprocal membrane photobioreactor (RMPBR) containing Chlorella vulgaris species: Hydraulic resistances assessment
BACKGROUND: The membrane photobioreactor is a combination of membrane technology and the photobioreactor system. It is an economic and efficient system for microalgae cultivation. Light cycles and its intensity are significant parameters in the biomass production and synthesis of metabolites, such as protein and carbohydrates, within the microalgae cells. These parameters can, therefore, have a significant impact on the rate and characteristics of fouling in membrane photobioreactor systems.RESULTS: In this work, Chlorella vulgaris (green microalgae) was cultivated within the designed reciprocal membrane photobioreactor (RMPBR) under 24–0, 16–8, and 12–12 light–dark (L/D) cycles. Also, the transmembrane pressure (TMP) and different hydraulic membrane resistances (cake layer, pore‐blocking, and fluid resistances) were investigated. The 16–8 L/D cycle had the fastest fouling time (96 h), highest pore‐blocking resistance (Rp), and the maximum concentrations of protein and carbohydrate in the supernatant and permeate flux. However, the 12–12 L/D recorded the maximum cake layer resistance (Rc), the highest content of protein within the cake layer, and the longest fouling time (226 h). Additionally, the highest carbohydrate concentration within the cake layer was for the 24–0 L/D regime, and it was fouled after 162 h.CONCLUSION: The Rc for each cycle had the highest values compared to the other calculated resistances. When the membrane is fouled, the mechanical membrane cleaning method employed in the RMPBR, which is in the form of an automatic spongy blade, cleans the cake layer on the membrane and improves its operation up to 80% via decreasing the Rt of the system. © 2020 Society of Chemical Industry (SCI)
- 1 September 2019
- Published by Elsevier in Chemosphere
- Vol. 230, 316-326
Gaining deeper insights into the bioflocculation process occurring in a high loaded membrane bioreactor used for the treatment of synthetic greywater
- 1 September 2019
- Published by Elsevier in Chemosphere
- Vol. 230, 316-326
Gaining deeper insights into the bioflocculation process occurring in a high loaded membrane bioreactor used for the treatment of synthetic greywater
- 1 August 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (4) , 5536-5543
The development of aerobic granules from slaughterhouse wastewater in treating real dyeing wastewater by Sequencing Batch Reactor (SBR)
- 1 August 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (4) , 5536-5543
The development of aerobic granules from slaughterhouse wastewater in treating real dyeing wastewater by Sequencing Batch Reactor (SBR)
- 14 December 2017
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 37 (4) , 1380-1393
Simulation of mineral dust aerosols in southwestern iran through numerical prediction models
Using the Numerical Prediction Models in mineral dust cycle is of prime importance in investigation of aerosol contribution in climatic changes. In this paper, a modelling system is developed to study a local characterization of Shalamceh dust intrusions in PM10 levels in Ahvaz city. The model chain consists of three different modules: the meteorological model (WRF), the dust emission model (COMSALT) and transport/deposition model (CAMx). Applying a physically based parameterization of the vertical dust fluxes emitted from the eroding soil could reduce the need for empirical source functions in dust emission models. For the selected case study, 6/1/2010 and 6/10/2010, the numerical simulations were performed to evaluate the effectiveness of modeling system. The comparison between observation and modeled results shows a good agreement. Different scenarios used to investigate the role of desertification and weak structure soils in air quality. Results show an increase in PM10 levels in Ahvaz due to the growth of wind erodible lands and the reduction of soil cohesive forces. In addition, the dry deposition fluxes of some detected heavy metals in different situations were estimated. Also, dust emission potential was inspected with the absorbing aerosol index data from Ozone Measurement Instrument (OMI) in the studied area. © 2017 American Institute of Chemical Engineers Environ Prog, 37: 1380–1393, 2018
- 14 December 2017
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 37 (4) , 1380-1393
Simulation of mineral dust aerosols in southwestern iran through numerical prediction models
Using the Numerical Prediction Models in mineral dust cycle is of prime importance in investigation of aerosol contribution in climatic changes. In this paper, a modelling system is developed to study a local characterization of Shalamceh dust intrusions in PM10 levels in Ahvaz city. The model chain consists of three different modules: the meteorological model (WRF), the dust emission model (COMSALT) and transport/deposition model (CAMx). Applying a physically based parameterization of the vertical dust fluxes emitted from the eroding soil could reduce the need for empirical source functions in dust emission models. For the selected case study, 6/1/2010 and 6/10/2010, the numerical simulations were performed to evaluate the effectiveness of modeling system. The comparison between observation and modeled results shows a good agreement. Different scenarios used to investigate the role of desertification and weak structure soils in air quality. Results show an increase in PM10 levels in Ahvaz due to the growth of wind erodible lands and the reduction of soil cohesive forces. In addition, the dry deposition fluxes of some detected heavy metals in different situations were estimated. Also, dust emission potential was inspected with the absorbing aerosol index data from Ozone Measurement Instrument (OMI) in the studied area. © 2017 American Institute of Chemical Engineers Environ Prog, 37: 1380–1393, 2018