Parisa Bazazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Parisa Bazazi has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Seyed Hossein Hejazi
Department of Chemical and Petroleum Engineering, University of Calgary, Calgary, AB T2N 1N4, Canada
9 shared publications - Howard A. Stone
Department of Mechanical and Aerospace Engineering, Princeton University, Princeton, NJ 08544 USA
5 shared publications - Aimen Laalam
Petroleum Engineering Department, Colorado School of Mines, Golden, CO 80401, USA
3 shared publications Amir Sanati-Nezhad
2 shared publications- Carlos Torres-Verdín
Hildebrand Department of Petroleum and Geosystems Engineering The University of Texas at Austin Austin TX USA
2 shared publications - Cheng Chen
Department of Civil, Environmental and Ocean Engineering, Stevens Institute of Technology
2 shared publications
Latest Publications
- 1 November 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- p. 1-14
Laboratory Measurements of Hydraulic and Electrical Conductivity of Fractures Generated with Electrically Conductive Proppant for Enhanced Geothermal Applications
Summary: Hydraulic fracturing with proppants is essential for sustaining permeability in enhanced geothermal systems (EGS), yet monitoring fracture geometry and proppant placement remains a major challenge. In this work, we demonstrate that electrically conductive (EC) proppants provide a robust platform for simultaneous fracture support and electromagnetic (EM) imaging. We experimentally quantify the coupled hydraulic and electrical transport properties of EC proppant-supported fractures under stress and temperature conditions representative of the Utah Frontier Observatory for Research in Geothermal Energy (FORGE) geothermal reservoir. Results show that EC proppants provide adequate hydraulic conductivity and considerable electrical conductivity contrast under EGS temperature and stress conditions. Hydraulic conductivity exhibits a nonmonotonic dependence on proppant loading that allows high fracture conductivity to be maintained with partial-monolayer proppant packs. In contrast, the role of EC fluids on the overall electrical conductivity depends on the EC proppant concentration, and electrical transport is governed by distinct conduction mechanisms that evolve with packing structure: Ionic conduction through the KCl solution and particle–fluid–particle electrical pathways dominate at sparse coverages, whereas direct particle contacts control electrical conductivity in densely packed fractures. Consequently, EC pathways emerge before full-monolayer EC proppant coverage is achieved, enabling detection of proppant-deficient regions near fracture tips. Even under monolayer packing, EC proppant-supported fractures remain more than five orders of magnitude more conductive than the surrounding granite, providing a strong EC contrast for subsurface imaging and a strong EM response under EGS conditions. Measurements on FORGE field samples further confirm the applicability of this approach under realistic EGS conditions. These results establish the transport physics of EC proppant networks and provide a foundation for real-time EM monitoring of hydraulically fractured geothermal reservoirs.
- 1 November 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- p. 1-14
Laboratory Measurements of Hydraulic and Electrical Conductivity of Fractures Generated with Electrically Conductive Proppant for Enhanced Geothermal Applications
Summary: Hydraulic fracturing with proppants is essential for sustaining permeability in enhanced geothermal systems (EGS), yet monitoring fracture geometry and proppant placement remains a major challenge. In this work, we demonstrate that electrically conductive (EC) proppants provide a robust platform for simultaneous fracture support and electromagnetic (EM) imaging. We experimentally quantify the coupled hydraulic and electrical transport properties of EC proppant-supported fractures under stress and temperature conditions representative of the Utah Frontier Observatory for Research in Geothermal Energy (FORGE) geothermal reservoir. Results show that EC proppants provide adequate hydraulic conductivity and considerable electrical conductivity contrast under EGS temperature and stress conditions. Hydraulic conductivity exhibits a nonmonotonic dependence on proppant loading that allows high fracture conductivity to be maintained with partial-monolayer proppant packs. In contrast, the role of EC fluids on the overall electrical conductivity depends on the EC proppant concentration, and electrical transport is governed by distinct conduction mechanisms that evolve with packing structure: Ionic conduction through the KCl solution and particle–fluid–particle electrical pathways dominate at sparse coverages, whereas direct particle contacts control electrical conductivity in densely packed fractures. Consequently, EC pathways emerge before full-monolayer EC proppant coverage is achieved, enabling detection of proppant-deficient regions near fracture tips. Even under monolayer packing, EC proppant-supported fractures remain more than five orders of magnitude more conductive than the surrounding granite, providing a strong EC contrast for subsurface imaging and a strong EM response under EGS conditions. Measurements on FORGE field samples further confirm the applicability of this approach under realistic EGS conditions. These results establish the transport physics of EC proppant networks and provide a foundation for real-time EM monitoring of hydraulically fractured geothermal reservoirs.
- 3 August 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (10) , 6951-6963
Carbon Black Suspension as Electrically Conductive Fracturing Fluid for Fracture Diagnostics in Enhanced Geothermal Systems
Summary: Fracture diagnostics in subsurface energy systems using a low-frequency electromagnetic (EM) induction method requires a high electrical conductivity contrast between propped fractures and the surrounding formations. Conventional electrolyte-based fluids suffer from salt precipitation and corrosion at enhanced geothermal system (EGS) temperatures exceeding 150°C, which limits their applicability. While carbon black (CB) suspensions are widely used in composite materials and industrial fluids, their performance at EGS reservoir conditions and suitability as a fracturing fluid additive have not been previously characterized. In this study, we investigate CB suspensions as dual-function fracturing fluid additives that simultaneously enhance electrical conductivity for EM-based fracture diagnostics and improve proppant transport through viscosity enhancement at high temperature and pressure. CB suspensions at 0.1 wt%, 0.5 wt%, and 1.0 wt% were tested at pressures up to 2,000 psi and temperatures up to 200°C, with viscosity measured via the Hagen-Poiseuille pressure-drop analysis and cross-validated using a rotational rheometer. CB suspensions achieved electrical conductivities up to 0.5 S m⁻¹ at 200°C and 2,000 psi, exceeding granitic formation conductivity by more than four orders of magnitude. Conductivity follows Arrhenius behavior with temperature and a percolation power law with concentration, and an empirical correlation was developed for EGS stimulation design. Adding 1 wt% CB increases fluid viscosity by 30–40% at high temperature and pressure, which reduces proppant settling velocity by 19–21% at 200°C and improves proppant transport without the corrosion and precipitation risks associated with conventional electrolyte-based solutions. A 3D frequency-domain EM forward model confirms that a conductive proppant pack can generate induction logging signals above the formation background, which can be used to detect propped fractures in EGS.
- 3 August 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (10) , 6951-6963
Carbon Black Suspension as Electrically Conductive Fracturing Fluid for Fracture Diagnostics in Enhanced Geothermal Systems
Summary: Fracture diagnostics in subsurface energy systems using a low-frequency electromagnetic (EM) induction method requires a high electrical conductivity contrast between propped fractures and the surrounding formations. Conventional electrolyte-based fluids suffer from salt precipitation and corrosion at enhanced geothermal system (EGS) temperatures exceeding 150°C, which limits their applicability. While carbon black (CB) suspensions are widely used in composite materials and industrial fluids, their performance at EGS reservoir conditions and suitability as a fracturing fluid additive have not been previously characterized. In this study, we investigate CB suspensions as dual-function fracturing fluid additives that simultaneously enhance electrical conductivity for EM-based fracture diagnostics and improve proppant transport through viscosity enhancement at high temperature and pressure. CB suspensions at 0.1 wt%, 0.5 wt%, and 1.0 wt% were tested at pressures up to 2,000 psi and temperatures up to 200°C, with viscosity measured via the Hagen-Poiseuille pressure-drop analysis and cross-validated using a rotational rheometer. CB suspensions achieved electrical conductivities up to 0.5 S m⁻¹ at 200°C and 2,000 psi, exceeding granitic formation conductivity by more than four orders of magnitude. Conductivity follows Arrhenius behavior with temperature and a percolation power law with concentration, and an empirical correlation was developed for EGS stimulation design. Adding 1 wt% CB increases fluid viscosity by 30–40% at high temperature and pressure, which reduces proppant settling velocity by 19–21% at 200°C and improves proppant transport without the corrosion and precipitation risks associated with conventional electrolyte-based solutions. A 3D frequency-domain EM forward model confirms that a conductive proppant pack can generate induction logging signals above the formation background, which can be used to detect propped fractures in EGS.
- Open Access
- 12 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 249
Geological generation, global potential, and techno-economic assessment of natural hydrogen systems
- 12 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 249
Open AccessGeological generation, global potential, and techno-economic assessment of natural hydrogen systems
- Open Access
- 3 June 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (24) , 12736-12746
Role of 3-Pentanone in CO 2 –WAG Injection for Post-Waterflood Residual Oil Recovery
- 3 June 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (24) , 12736-12746
Open AccessRole of 3-Pentanone in CO 2 –WAG Injection for Post-Waterflood Residual Oil Recovery
- Open Access
- 6 April 2026
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 22 (18) , 3359-3369
Dynamics of emulsion drop impact, spreading and evaporation: the effect of internal phase gelation
The dynamics of drop impact, spreading, and evaporation on solid surfaces are fundamental to many processes, including agricultural spraying, printing, combustion, and coating. While these behaviors are well understood for single phase liquids, less is known about emulsions with complex internal structures. Here, we report an experimental study on the dynamics of water-in-oil emulsion droplets containing either liquid or gelled aqueous phases. The continuous phase is composed of $n$-heptane and Span 80 micelles, while the dispersed phase is a reactive sodium silicate–ammonium bicarbonate solution that undergoes gelation. Internal gelation changes the rheological response of the dispersed phase and is therefore to modify dissipation during spreading and drying. During the impact stage, the dynamics are similar for both emulsion types within our experimental resolution, whereas during the subsequent spreading stage gel-containing emulsions reach smaller wetted areas. Measured maximum spreading factors are broadly consistent with unified inertial--capillary--viscous scaling for water emulsions, while gel emulsions show systematic deviations at higher internal-phase fractions. Bottom-view fluorescence imaging reveals distinct drying patterns: isolated circular deposits for water emulsions and rugged, interconnected structures for gel emulsions. These findings highlight the importance of internal droplet structure in governing impact and drying dynamics, with implications for a wide range of emulsion-based technologies.
- 6 April 2026
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 22 (18) , 3359-3369
Open AccessDynamics of emulsion drop impact, spreading and evaporation: the effect of internal phase gelation
The dynamics of drop impact, spreading, and evaporation on solid surfaces are fundamental to many processes, including agricultural spraying, printing, combustion, and coating. While these behaviors are well understood for single phase liquids, less is known about emulsions with complex internal structures. Here, we report an experimental study on the dynamics of water-in-oil emulsion droplets containing either liquid or gelled aqueous phases. The continuous phase is composed of $n$-heptane and Span 80 micelles, while the dispersed phase is a reactive sodium silicate–ammonium bicarbonate solution that undergoes gelation. Internal gelation changes the rheological response of the dispersed phase and is therefore to modify dissipation during spreading and drying. During the impact stage, the dynamics are similar for both emulsion types within our experimental resolution, whereas during the subsequent spreading stage gel-containing emulsions reach smaller wetted areas. Measured maximum spreading factors are broadly consistent with unified inertial--capillary--viscous scaling for water emulsions, while gel emulsions show systematic deviations at higher internal-phase fractions. Bottom-view fluorescence imaging reveals distinct drying patterns: isolated circular deposits for water emulsions and rugged, interconnected structures for gel emulsions. These findings highlight the importance of internal droplet structure in governing impact and drying dynamics, with implications for a wide range of emulsion-based technologies.
- Open Access
- 26 February 2026
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 714, 140170
Capillary breakup of emulsion filaments tuned by in situ gelation of dispersed droplets
- 26 February 2026
- Published by Elsevier in Journal of Colloid and Interface Science
- Vol. 714, 140170
Open AccessCapillary breakup of emulsion filaments tuned by in situ gelation of dispersed droplets
- 12 November 2025
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 10 (11)
Suppression of short-term oscillations in falling droplets by viscoelastic interfacial layers
- 12 November 2025
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 10 (11)
Suppression of short-term oscillations in falling droplets by viscoelastic interfacial layers
- Open Access
- 27 August 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 169
Holding the invisible: Advanced materials for hydrogen storage
- 27 August 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 169
Open AccessHolding the invisible: Advanced materials for hydrogen storage
- Open Access
- 13 January 2025
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 21 (7) , 1296-1307
Pinch-off dynamics of emulsion filaments before and after polymerization of the internal phase
We study the capillary breakup dynamics of fluid filaments with polymerized and unpolymerized droplets, showing how emulsion composition and polymerization impact rheology and pinch-off for bio-ink optimization in 3D printing.
- 13 January 2025
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 21 (7) , 1296-1307
Open AccessPinch-off dynamics of emulsion filaments before and after polymerization of the internal phase
We study the capillary breakup dynamics of fluid filaments with polymerized and unpolymerized droplets, showing how emulsion composition and polymerization impact rheology and pinch-off for bio-ink optimization in 3D printing.
- 11 March 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (3) , L032301
Hydrodynamic interactions between rough surfaces
In the study of particle suspensions, away from the jamming threshold, it is common to interpret the effective viscosity in terms of the volume fraction, neglecting roughness effects. Here we show that particle roughness can significantly modify viscous dissipation in configurations that represent fixed volume-fraction conditions. We derive a hydrodynamic model for the forced interaction of a two-dimensional particle, where roughness is represented by a periodic corrugation, with an adjacent wall. In particular, we address the limit of small nominal particle-wall separation, with the corrugation amplitude comparable with said separation. A lubrication analysis provides the rectilinear and angular velocities of the particle as functions of the instantaneous angular configuration. The particle may either translate while rotating or become “locked” in a specific phase and translate without rotation. The time-averaged rectilinear velocity, which is the object of interest, is a purely geometric quantity, obtained without the need to address any time dynamics.
- 11 March 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (3) , L032301
Hydrodynamic interactions between rough surfaces
In the study of particle suspensions, away from the jamming threshold, it is common to interpret the effective viscosity in terms of the volume fraction, neglecting roughness effects. Here we show that particle roughness can significantly modify viscous dissipation in configurations that represent fixed volume-fraction conditions. We derive a hydrodynamic model for the forced interaction of a two-dimensional particle, where roughness is represented by a periodic corrugation, with an adjacent wall. In particular, we address the limit of small nominal particle-wall separation, with the corrugation amplitude comparable with said separation. A lubrication analysis provides the rectilinear and angular velocities of the particle as functions of the instantaneous angular configuration. The particle may either translate while rotating or become “locked” in a specific phase and translate without rotation. The time-averaged rectilinear velocity, which is the object of interest, is a purely geometric quantity, obtained without the need to address any time dynamics.