Nikolai Hangst
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nikolai Hangst has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Thomas M. Wendt
Hochschule Offenburg
6 shared publications - Lukas Stiglmeier
Work-Life Robotics Institute, Offenburg University of Applied Sciences,Offenburg,Germany
3 shared publications - Philipp Gawron
Work-Life Robotics Institute, Offenburg University of Applied Sciences, Offenburg, Germany
2 shared publications S. J. Rupitsch
Department of Microsystems Engineering Laboratory for Electrical Instrumentation and Embedded Systems University of Freiburg Freiburg Germany
2 shared publicationsT. M. Wendt
2 shared publications- Urban B. Himmelsbach
Work-Life Robotics Laboratory, Department of Business and Industrial Engineering, Offenburg University of Applied Sciences, 77723 Gengenbach, Germany
2 shared publications
Latest Publications
- Open Access
- 6 December 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 399
Fully 3D-printed gripper jaw with embedded sensitive sensor structures for robotic applications
- 6 December 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 399
Open AccessFully 3D-printed gripper jaw with embedded sensitive sensor structures for robotic applications
- 29 August 2025
- Published by Springer Nature
- p. 19-30
From University to Industry: Holistic Robotics Education for Tomorrow’s Challenges
- 29 August 2025
- Published by Springer Nature
- p. 19-30
From University to Industry: Holistic Robotics Education for Tomorrow’s Challenges
- 14 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (16) , 30484-30495
Additive Manufactured Sensitive Gripper Jaw for Extended Gripping Force Ranges in Robotics
In this contribution, we present a novel additive manufactured sensitive gripper jaw based on strain gauge technology for extended gripping force ranges in robotics up to 40 N using Fused Layer Manufacturing. The present sensor design is based on an arbitrary number of bending beams arranged one above the other, based on a single point load cell. With this multiple bending beam structure, it is possible to individually reduce the mechanical stresses while maintaining the same deflection of the gripper jaw and enabling parallel gripping of parts. By varying the number of bending beams, it is also possible to adapt the measurement range accordingly. The investigations focus on the general sensor design, the fabrication process, and the sensor behavior in terms of zero-point deviation, characteristic value deviation, linearity behavior, repeatability, and viscoelastic behavior. The results show that higher gripping force measurement ranges are possible with good sensor linearity of 0.14 % of full scale. The arising viscoelastic behavior can be attributed to the properties of plastics. Nevertheless, this sensor is suitable for gripping force measurement in most industrial robot applications.
- 14 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (16) , 30484-30495
Additive Manufactured Sensitive Gripper Jaw for Extended Gripping Force Ranges in Robotics
In this contribution, we present a novel additive manufactured sensitive gripper jaw based on strain gauge technology for extended gripping force ranges in robotics up to 40 N using Fused Layer Manufacturing. The present sensor design is based on an arbitrary number of bending beams arranged one above the other, based on a single point load cell. With this multiple bending beam structure, it is possible to individually reduce the mechanical stresses while maintaining the same deflection of the gripper jaw and enabling parallel gripping of parts. By varying the number of bending beams, it is also possible to adapt the measurement range accordingly. The investigations focus on the general sensor design, the fabrication process, and the sensor behavior in terms of zero-point deviation, characteristic value deviation, linearity behavior, repeatability, and viscoelastic behavior. The results show that higher gripping force measurement ranges are possible with good sensor linearity of 0.14 % of full scale. The arising viscoelastic behavior can be attributed to the properties of plastics. Nevertheless, this sensor is suitable for gripping force measurement in most industrial robot applications.
- Open Access
- 1 January 2025
- Published by AMA Service GmbH
- p. 151-152
C4.1 - Additive Manufactured Capacitive Sensor for Slip Detection with Seamless Integration of Object Recognition and Differentiation in Robot Grippers
In this contribution, we present a novel additive manufactured capacitive sensor for slip detection with seamless integration of object recognition and differentiation in robot grippers. The sensor consists of a measuring electrode in combination with guarding and shielding electrodes to reduce edge effects and disruptive influences. The results show precise slip detection through linear sensor behavior. In addition, object detection and differentiation are possible.
- 1 January 2025
- Published by AMA Service GmbH
- p. 151-152
Open AccessC4.1 - Additive Manufactured Capacitive Sensor for Slip Detection with Seamless Integration of Object Recognition and Differentiation in Robot Grippers
In this contribution, we present a novel additive manufactured capacitive sensor for slip detection with seamless integration of object recognition and differentiation in robot grippers. The sensor consists of a measuring electrode in combination with guarding and shielding electrodes to reduce edge effects and disruptive influences. The results show precise slip detection through linear sensor behavior. In addition, object detection and differentiation are possible.
- Open Access
- 1 January 2025
- Published by AMA Service GmbH
- p. 155-156
C4.3 - Optimized Grasp Planning for Bin-Picking Robots with 2D and 3D Sensor Data
Bin-picking systems face challenges in fully emptying containers due to collision risks in real-world scenarios. In this contribution, we present a grasp planning approach that combines 2D and 3D sensor data to ensure collision-free handling. The method is successfully tested on objects with eccentric centers of mass and is implemented directly on the robot's control unit, eliminating the need for separate computing hardware.
- 1 January 2025
- Published by AMA Service GmbH
- p. 155-156
Open AccessC4.3 - Optimized Grasp Planning for Bin-Picking Robots with 2D and 3D Sensor Data
Bin-picking systems face challenges in fully emptying containers due to collision risks in real-world scenarios. In this contribution, we present a grasp planning approach that combines 2D and 3D sensor data to ensure collision-free handling. The method is successfully tested on objects with eccentric centers of mass and is implemented directly on the robot's control unit, eliminating the need for separate computing hardware.
- Open Access
- 1 January 2024
- Published by AMA Service GmbH
- p. 225-229
C1.4 - Different Ways to Simplify a Simulation Model of an Additively Manufactured Force Sensor with Embedded Constantan Wires as Sensing Elements in the Field of Robot Gripping Technology
In this contribution, we present different ways to simplify a simulation model of an additively manufactured force sensor in the field of robot gripping technology for efficient determination of results using COMSOL Multiphysics. The results of different computational approaches are compared with the required computing time and memory requirements. A simplified analytical approach is also presented as an alternative and to verify the plausibility of the simulations.
- 1 January 2024
- Published by AMA Service GmbH
- p. 225-229
Open AccessC1.4 - Different Ways to Simplify a Simulation Model of an Additively Manufactured Force Sensor with Embedded Constantan Wires as Sensing Elements in the Field of Robot Gripping Technology
In this contribution, we present different ways to simplify a simulation model of an additively manufactured force sensor in the field of robot gripping technology for efficient determination of results using COMSOL Multiphysics. The results of different computational approaches are compared with the required computing time and memory requirements. A simplified analytical approach is also presented as an alternative and to verify the plausibility of the simulations.
- Open Access
Human–Machine Differentiation in Speed and Separation Monitoring for Improved Efficiency in Human–Robot Collaboration
Human–robot collaborative applications have been receiving increasing attention in industrial applications. The efficiency of the applications is often quite low compared to traditional robotic applications without human interaction. Especially for applications that use speed and separation monitoring, there is potential to increase the efficiency with a cost-effective and easy to implement method. In this paper, we proposed to add human–machine differentiation to the speed and separation monitoring in human–robot collaborative applications. The formula for the protective separation distance was extended with a variable for the kind of object that approaches the robot. Different sensors for differentiation of human and non-human objects are presented. Thermal cameras are used to take measurements in a proof of concept. Through differentiation of human and non-human objects, it is possible to decrease the protective separation distance between the robot and the object and therefore increase the overall efficiency of the collaborative application.
Open AccessHuman–Machine Differentiation in Speed and Separation Monitoring for Improved Efficiency in Human–Robot Collaboration
Human–robot collaborative applications have been receiving increasing attention in industrial applications. The efficiency of the applications is often quite low compared to traditional robotic applications without human interaction. Especially for applications that use speed and separation monitoring, there is potential to increase the efficiency with a cost-effective and easy to implement method. In this paper, we proposed to add human–machine differentiation to the speed and separation monitoring in human–robot collaborative applications. The formula for the protective separation distance was extended with a variable for the kind of object that approaches the robot. Different sensors for differentiation of human and non-human objects are presented. Thermal cameras are used to take measurements in a proof of concept. Through differentiation of human and non-human objects, it is possible to decrease the protective separation distance between the robot and the object and therefore increase the overall efficiency of the collaborative application.
- Open Access
A Review on Kinetic Energy Harvesting with Focus on 3D Printed Electromagnetic Vibration Harvesters
The increasing amount of Internet of Things (IoT) devices and wearables require a reliable energy source. Energy harvesting can power these devices without changing batteries. Three-dimensional printing allows us to manufacture tailored harvesting devices in an easy and fast way. This paper presents the development of hybrid and non-hybrid 3D printed electromagnetic vibration energy harvesters. Various harvesting approaches, their utilised geometry, functional principle, power output and the applied printing processes are shown. The gathered harvesters are analysed, challenges examined and research gaps in the field identified. The advantages and challenges of 3D printing harvesters are discussed. Reported applications and strategies to improve the performance of printed harvesting devices are presented.
Open AccessA Review on Kinetic Energy Harvesting with Focus on 3D Printed Electromagnetic Vibration Harvesters
The increasing amount of Internet of Things (IoT) devices and wearables require a reliable energy source. Energy harvesting can power these devices without changing batteries. Three-dimensional printing allows us to manufacture tailored harvesting devices in an easy and fast way. This paper presents the development of hybrid and non-hybrid 3D printed electromagnetic vibration energy harvesters. Various harvesting approaches, their utilised geometry, functional principle, power output and the applied printing processes are shown. The gathered harvesters are analysed, challenges examined and research gaps in the field identified. The advantages and challenges of 3D printing harvesters are discussed. Reported applications and strategies to improve the performance of printed harvesting devices are presented.
- 1 September 2020
- Published by Springer Nature
- p. 415-425
Design of an Additively Manufactured Customized Gripper System for Human Robot Collaboration
- 1 September 2020
- Published by Springer Nature
- p. 415-425
Design of an Additively Manufactured Customized Gripper System for Human Robot Collaboration