Luis Henrique Rodovalho
Research Subjects
Luis Henrique Rodovalho has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Orazio Aiello
University of Genova
5 shared publicationsCesar Ramos Rodrigues
BEI, Federal Univ. of Santa Catarina,Florianopolis
4 shared publications- Cesar Ramos Rodrigues
Biomedical Engineering Institute, Federal University of Santa Catarina (IEB-UFSC), Florianópolis 88040-900, Brazil
4 shared publications - Orazio Aiello
University of Genoa
4 shared publications Eric Fabris
Microelectronics Graduate Program, Federal University of Rio Grande do Sul, Porto Alegre, Rio Grande do Sul
2 shared publicationsHamilton Klimach
Microelectronics Graduate Program, Federal University of Rio Grande do Sul, Porto Alegre, Rio Grande do Sul
2 shared publications
Latest Publications
- Open Access
Hybrid Inverter-Based Fully Differential Operational Transconductance Amplifiers
Inverter-based Operational Transconductance Amplifiers (OTAs) are versatile and friendly scalable analog circuit blocks. Especially for the new CMOS technological nodes, several recent applications have been extensively using them, ranging from Analog Front End (AFE) to analog-to-digital converters (ADC). This work tracks down the current advances in inverter-based OTAs design, comparing their basic fully differential structures, such as Nauta (N), Barthelemy (B), Vieru (V) and Mafredini (M) ones, and, in addition, mixing them up to propose new fully differential single-ended and two-stage hybrid versions. The new herein-proposed fully differential hybrid OTAs are the composition of Barthelemy/Nauta (B/N), Barthelemy/Manfredini (B/M), Nauta/Vieru (N/V), and Manfredini/Vieru (M/V) OTAs. All OTAs were designed using the same Global Foundries 180 nm open-source PDK and their performances are compared for post-layout simulations.
Open AccessHybrid Inverter-Based Fully Differential Operational Transconductance Amplifiers
Inverter-based Operational Transconductance Amplifiers (OTAs) are versatile and friendly scalable analog circuit blocks. Especially for the new CMOS technological nodes, several recent applications have been extensively using them, ranging from Analog Front End (AFE) to analog-to-digital converters (ADC). This work tracks down the current advances in inverter-based OTAs design, comparing their basic fully differential structures, such as Nauta (N), Barthelemy (B), Vieru (V) and Mafredini (M) ones, and, in addition, mixing them up to propose new fully differential single-ended and two-stage hybrid versions. The new herein-proposed fully differential hybrid OTAs are the composition of Barthelemy/Nauta (B/N), Barthelemy/Manfredini (B/M), Nauta/Vieru (N/V), and Manfredini/Vieru (M/V) OTAs. All OTAs were designed using the same Global Foundries 180 nm open-source PDK and their performances are compared for post-layout simulations.
- Open Access
- 15 June 2022
- Published by Springer Nature in Research Square
Rail-to-Rail Input/Output Bulk Driven Class AB Operational Amplifier with Improved Composite Transistors (Invited paper)
This work presents two-stage single-ended Operational Transconductance Amplifiers (OTA) with very high voltage gain and rail-to-rail output voltage excursion. This is achieved by using Improved Composite Transistors (ICT) with safe forward-body-biasing, so the amplifier can be used with typical I/O supply voltages and high-VT thick-oxide transistors without significant parasitic substrate current. Two versions of the same OTA were designed and simulated using the open-source Skywater 130 nm PDK. The first version, made of only Trapezoidal Transistor Arrays (TTA), achieves an 83 dB voltage gain, 13.1 MHz GBW, and 60° phase margin for a 10 pF capacitive load while demanding 122.1 µW of power at 3.0 V power supply. The proposed ICT OTA version attains about the same specifications, except for its voltage gain, which has increased by 37 dB, thus reaching 121 dB.
- 15 June 2022
- Published by Springer Nature in Research Square
Open AccessRail-to-Rail Input/Output Bulk Driven Class AB Operational Amplifier with Improved Composite Transistors (Invited paper)
This work presents two-stage single-ended Operational Transconductance Amplifiers (OTA) with very high voltage gain and rail-to-rail output voltage excursion. This is achieved by using Improved Composite Transistors (ICT) with safe forward-body-biasing, so the amplifier can be used with typical I/O supply voltages and high-VT thick-oxide transistors without significant parasitic substrate current. Two versions of the same OTA were designed and simulated using the open-source Skywater 130 nm PDK. The first version, made of only Trapezoidal Transistor Arrays (TTA), achieves an 83 dB voltage gain, 13.1 MHz GBW, and 60° phase margin for a 10 pF capacitive load while demanding 122.1 µW of power at 3.0 V power supply. The proposed ICT OTA version attains about the same specifications, except for its voltage gain, which has increased by 37 dB, thus reaching 121 dB.
- 22 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 9-12
Fully-differential inverter-based OTA with improved composite transistors
The paper deals with fully-differential inverter-based Operational Transconductance Amplifier (OTA) designed using rectangular transistor arrays (RTA) and improved composite transistors (ICT). The two versions of the same OTA are designed and the respective performance has been shown under aggressive supply voltage scaling down to 0.3V. Post-layout simulations referring to 180 nm CMOS process technology have shown how the ICT solution with its proper body bias offer a higher voltage gain, CMRR, PSRR and a lower power consumption compared to the respective RTA version.
- 22 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 9-12
Fully-differential inverter-based OTA with improved composite transistors
The paper deals with fully-differential inverter-based Operational Transconductance Amplifier (OTA) designed using rectangular transistor arrays (RTA) and improved composite transistors (ICT). The two versions of the same OTA are designed and the respective performance has been shown under aggressive supply voltage scaling down to 0.3V. Post-layout simulations referring to 180 nm CMOS process technology have shown how the ICT solution with its proper body bias offer a higher voltage gain, CMRR, PSRR and a lower power consumption compared to the respective RTA version.
- 22 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-16
An inverter-based OTA using improved composite transistors and bulk-driven common-mode rejection
This work presents a gate-driven fully-differential inverter-based Operational Transconductance Amplifier (OTA) with a proper body bias using both rectangular transistor arrays (RTA) and improved composite transistors (ICT). Two versions of the same OTA were designed and compared with post-layout simulations referring to a 180 nm CMOS process. Simulation results show that the RTA OTA version has a 38 dB voltage gain, achieves a 1.1 kHz GBW for a 10 pF load, and consumes 970 pW total power for a 0.3 V supply voltage. The ICT OTA version shows better performance resulting in 48 dB voltage gain, 0.91 kHz GBW for a 10 pF load, and 810 pW total power consumption for a 0.3 V supply voltage.
- 22 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-16
An inverter-based OTA using improved composite transistors and bulk-driven common-mode rejection
This work presents a gate-driven fully-differential inverter-based Operational Transconductance Amplifier (OTA) with a proper body bias using both rectangular transistor arrays (RTA) and improved composite transistors (ICT). Two versions of the same OTA were designed and compared with post-layout simulations referring to a 180 nm CMOS process. Simulation results show that the RTA OTA version has a 38 dB voltage gain, achieves a 1.1 kHz GBW for a 10 pF load, and consumes 970 pW total power for a 0.3 V supply voltage. The ICT OTA version shows better performance resulting in 48 dB voltage gain, 0.91 kHz GBW for a 10 pF load, and 810 pW total power consumption for a 0.3 V supply voltage.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A Two-Stage Single-Ended OTA with Improved Composite Transistors
This work presents a two-stage single-ended Operational Transconductance Amplifier (OTA) with very high voltage gain and rail-to-rail output voltage excursion. This is achieved by using Improved Composite Transistors (ICT) with safe forward-body-biasing, so the amplifier can be used with typical I/O supply voltages and high- VT thick-oxide transistors without significant parasitic substrate current. Two versions of the same OTA were designed and simulated using the TSMC 180 nm PDK. The first version, made of only Rectangular Transistor Arrays (RTA), achieved a 109 dB voltage gain, 195.8 kHz GBW, 59° phase margin for a 10 pF capacitive load, while 6.57 µW of power at 3.3 V power supply. The proposed ICT OTA version achieve about the same specifications, however, its voltage gain was 155 dB, a 41 dB increase.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A Two-Stage Single-Ended OTA with Improved Composite Transistors
This work presents a two-stage single-ended Operational Transconductance Amplifier (OTA) with very high voltage gain and rail-to-rail output voltage excursion. This is achieved by using Improved Composite Transistors (ICT) with safe forward-body-biasing, so the amplifier can be used with typical I/O supply voltages and high- VT thick-oxide transistors without significant parasitic substrate current. Two versions of the same OTA were designed and simulated using the TSMC 180 nm PDK. The first version, made of only Rectangular Transistor Arrays (RTA), achieved a 109 dB voltage gain, 195.8 kHz GBW, 59° phase margin for a 10 pF capacitive load, while 6.57 µW of power at 3.3 V power supply. The proposed ICT OTA version achieve about the same specifications, however, its voltage gain was 155 dB, a 41 dB increase.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
CMOS inverter linearization technique with active source degeneration
Inverter-based OTAs are versatile and voltage scalable analog circuit blocks, which can be used in several applications, ranging from signal processing to analog-to-digital converters. However, for subthreshold operation, the inverter transconductance is very non-linear, which can decrease the performance of such applications. This work proposes an active source degeneration linearization technique for CMOS inverters operating with ultra-low-voltage supplies, in addition to forward body-biasing to correct process, temperature, and supply voltage variability.
- 26 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
CMOS inverter linearization technique with active source degeneration
Inverter-based OTAs are versatile and voltage scalable analog circuit blocks, which can be used in several applications, ranging from signal processing to analog-to-digital converters. However, for subthreshold operation, the inverter transconductance is very non-linear, which can decrease the performance of such applications. This work proposes an active source degeneration linearization technique for CMOS inverters operating with ultra-low-voltage supplies, in addition to forward body-biasing to correct process, temperature, and supply voltage variability.
- Open Access
- 20 October 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (4) , 40
A 1.9 nW, Sub-1 V, 542 pA/V Linear Bulk-Driven OTA with 154 dB CMRR for Bio-Sensing Applications
In this paper, a new technique for improvement on the DC voltage gain, while keeping the high-linearity in symmetrical operational transconductance amplifier (OTA) bulk-driven (BD) topology is proposed. These features are achieved by allying two topological solutions: enhanced forward-body-biasing self-cascode current mirror, and source degeneration. The proposed concept is demonstrated through simulations with typical process parameters and Monte Carlo analysis on nominal transistors of the CMOS TSMC 180 nm node. Results indicate that the proposed OTA can achieve a very small transconductance, only 542 pA/V while keeping a voltage gain higher than 60 dB, 150 dB CMRR, and high linearity of 475 mVpp (1% THD), consuming only 1.9 nW for a supply voltage of 0.6 V. This set of features allows the proposed OTA to be an attractive solution for implementing OTA-C filters for the analog front-ends in wearable devices and bio-sensing.
- 20 October 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (4) , 40
Open AccessA 1.9 nW, Sub-1 V, 542 pA/V Linear Bulk-Driven OTA with 154 dB CMRR for Bio-Sensing Applications
In this paper, a new technique for improvement on the DC voltage gain, while keeping the high-linearity in symmetrical operational transconductance amplifier (OTA) bulk-driven (BD) topology is proposed. These features are achieved by allying two topological solutions: enhanced forward-body-biasing self-cascode current mirror, and source degeneration. The proposed concept is demonstrated through simulations with typical process parameters and Monte Carlo analysis on nominal transistors of the CMOS TSMC 180 nm node. Results indicate that the proposed OTA can achieve a very small transconductance, only 542 pA/V while keeping a voltage gain higher than 60 dB, 150 dB CMRR, and high linearity of 475 mVpp (1% THD), consuming only 1.9 nW for a supply voltage of 0.6 V. This set of features allows the proposed OTA to be an attractive solution for implementing OTA-C filters for the analog front-ends in wearable devices and bio-sensing.
- 1 September 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 110 (1) , 19-31
Schmitt trigger based single-ended voltage amplifier for ultra-low-voltage supplies
- 1 September 2021
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 110 (1) , 19-31
Schmitt trigger based single-ended voltage amplifier for ultra-low-voltage supplies
- Open Access
- 16 August 2021
- Published by Journal of Integrated Circuits and Systems in Journal of Integrated Circuits and Systems
- Vol. 16 (2) , 1-11
A 59 pA/V and 62 nW Differential OTA with 0.35% THD for Biomedical Applications
This paper presents a novel differential pA/V Operational Transconductance Amplifier (OTA) topology. The circuit is suitable for the implementation of fully integrated operational transconductance amplifier-capacitance (OTA-C) filters with small feature size capacitors, suited for electrophysiological signal acquisition and conditioning. Unlike typical OTA-Cs, the proposed topology consists of transconductance reduction technique based on unbalanced output branches thatallow current subtraction thus enabling transconductances in the order of pA/V. The technique is demonstrated through the design of a 59pA/V transconductor, which is very suited for designing long-time-constant filters. This OTA-C achieved a worst-case 0.35% THD with just 61.7nW average power consumption, which allows its applicability to biomedical implants. Simulations were carried out with STMicroelectronics 0.13µm HCMOS9 node using Cadence’s IC design tools. Weemployed the OTA in a design of a fourth-order bandpass filter with a narrow bandwidth of 12.5–21.8Hz. Similar results to the ideal transfer function, turn the proposed OTA ideal for biosensing-based applications.
- 16 August 2021
- Published by Journal of Integrated Circuits and Systems in Journal of Integrated Circuits and Systems
- Vol. 16 (2) , 1-11
Open AccessA 59 pA/V and 62 nW Differential OTA with 0.35% THD for Biomedical Applications
This paper presents a novel differential pA/V Operational Transconductance Amplifier (OTA) topology. The circuit is suitable for the implementation of fully integrated operational transconductance amplifier-capacitance (OTA-C) filters with small feature size capacitors, suited for electrophysiological signal acquisition and conditioning. Unlike typical OTA-Cs, the proposed topology consists of transconductance reduction technique based on unbalanced output branches thatallow current subtraction thus enabling transconductances in the order of pA/V. The technique is demonstrated through the design of a 59pA/V transconductor, which is very suited for designing long-time-constant filters. This OTA-C achieved a worst-case 0.35% THD with just 61.7nW average power consumption, which allows its applicability to biomedical implants. Simulations were carried out with STMicroelectronics 0.13µm HCMOS9 node using Cadence’s IC design tools. Weemployed the OTA in a design of a fourth-order bandpass filter with a narrow bandwidth of 12.5–21.8Hz. Similar results to the ideal transfer function, turn the proposed OTA ideal for biosensing-based applications.