João Gabriel da Cruz Passos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
João Gabriel da Cruz Passos has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Artur Mariano de Sousa Malafaia
Universidade Federal de São João Del-Rei, Brasil
8 shared publications - Carlos Alberto Della Rovere
Munir Rachid Corrosion Laboratory, Department of Materials Engineering, Federal University of São Carlos, Rodovia Washington Luis Km 235, São Carlos 13565-905, SP, Brazil
5 shared publications - Rodrigo Silva
Munir Rachid Corrosion Laboratory, Department of Materials Engineering, Federal University of São Carlos, Rodovia Washington Luis Km 235, São Carlos 13565-905, SP, Brazil
5 shared publications - Ana Flávia Oliveira Alencar
Universidade Federal de São João del-Rei
2 shared publications - Bruno Xavier de Freitas
Universidade Federal de Itajubá, Brasil
2 shared publications C.A.D. Rovere
2 shared publications
Latest Publications
- Open Access
- 11 October 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-12
High-Temperature Oxidation of Ta-Ti-(Nb)-Al-Cr-Mo Refractory High-Entropy Alloys. Part I: Isothermal oxidation
High-entropy refractory alloys (RHEAs) have attracted increasing interest in the scientific community due to their potential for applications in extreme temperature and oxidation conditions. Composed of multiple elements, they exhibit unexpected combinations of properties that positions them as potential substitutes to currently used materials. This study analyzed the oxidation of three RHEAs in the Ta-Ti-(Nb)-Al-Cr-Mo system, consisting in the TaTiAlCrMo equiatomic alloy, and two modifications of it, a non-equiatomic one, and one with partial substitution of Mo by Nb. They were exposed isothermally to 1000 °C for 20, 100, and 300 h under laboratory air. The equiatomic alloy gained less mass and formed uniform, thin, and adherent oxide layers, while the alloy with Nb showed a significantly increased mass gain, forming porous layers and reaching a breakaway oxidation stage; the non-equiatomic alloy showed apparently more irregular and thicker layers, but still exhibited a protective behavior. The predominantly formed oxides were the rutile-type (Cr,Ta,Ti)O 2 , and possibly Al 2 O 3 , Cr 2 O 3 , and Nb 2 O 5 . All alloys showed oxygen absorption in the substrate , which was more pronounced for the non-equiatomic alloy and the alloy with Nb. In general, it became clear that the chemical composition and microstructure of the alloys are crucial factors in defining oxidation resistance.
- 11 October 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-12
Open AccessHigh-Temperature Oxidation of Ta-Ti-(Nb)-Al-Cr-Mo Refractory High-Entropy Alloys. Part I: Isothermal oxidation
High-entropy refractory alloys (RHEAs) have attracted increasing interest in the scientific community due to their potential for applications in extreme temperature and oxidation conditions. Composed of multiple elements, they exhibit unexpected combinations of properties that positions them as potential substitutes to currently used materials. This study analyzed the oxidation of three RHEAs in the Ta-Ti-(Nb)-Al-Cr-Mo system, consisting in the TaTiAlCrMo equiatomic alloy, and two modifications of it, a non-equiatomic one, and one with partial substitution of Mo by Nb. They were exposed isothermally to 1000 °C for 20, 100, and 300 h under laboratory air. The equiatomic alloy gained less mass and formed uniform, thin, and adherent oxide layers, while the alloy with Nb showed a significantly increased mass gain, forming porous layers and reaching a breakaway oxidation stage; the non-equiatomic alloy showed apparently more irregular and thicker layers, but still exhibited a protective behavior. The predominantly formed oxides were the rutile-type (Cr,Ta,Ti)O 2 , and possibly Al 2 O 3 , Cr 2 O 3 , and Nb 2 O 5 . All alloys showed oxygen absorption in the substrate , which was more pronounced for the non-equiatomic alloy and the alloy with Nb. In general, it became clear that the chemical composition and microstructure of the alloys are crucial factors in defining oxidation resistance.
- Open Access
- 28 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-16
High-Temperature Oxidation Behavior of a Novel Compositionally Complex Stainless Steel at 800 and 1000 °C
Compositionally complex alloys, derived from high-entropy alloys, are promising new materials that often present synergetic effects due to their complex compositions that give them properties surpassing conventional alloys. In this study, a medium-Cr compositionally complex stainless steel (CCSS) containing Ni, Co, Si, and Mo was evaluated under isothermal oxidation at 800 and 1000 °C in dry air. At 800 °C, the alloy exhibited protective behavior with a parabolic mass-gain rate (kp = 1.002 × 10 −4 mg 2 cm −4 h −1 ), forming a predominantly chromia-based scale accompanied by discontinuous spinel and mixed M 2 O 3 oxides. A silica subscale was detected at the metal/oxide interface, and Laves-phase precipitates influenced oxidation by acting as diffusion barriers and local Si reservoirs. At 1000 °C, however, extensive scale cracking and spallation occurred after the shortest exposure time used in this study (24 h), hindering the establishment of a stable protective layer. Although chromia remained the main oxide, volatilization and mechanical degradation led to breakaway oxidation. The presence, distribution, and evolution of Laves-phase precipitates were found to strongly affect both diffusion processes and scale integrity. Overall, the alloy demonstrated promising high-temperature performance at 800 °C due to its lower mass variation and simple oxide scale formed during exposure compared to conventional stainless steels but insufficient resistance at 1000 °C, especially considering its higher cost, indicating potential applicability at intermediate temperatures.
- 28 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- p. 1-16
Open AccessHigh-Temperature Oxidation Behavior of a Novel Compositionally Complex Stainless Steel at 800 and 1000 °C
Compositionally complex alloys, derived from high-entropy alloys, are promising new materials that often present synergetic effects due to their complex compositions that give them properties surpassing conventional alloys. In this study, a medium-Cr compositionally complex stainless steel (CCSS) containing Ni, Co, Si, and Mo was evaluated under isothermal oxidation at 800 and 1000 °C in dry air. At 800 °C, the alloy exhibited protective behavior with a parabolic mass-gain rate (kp = 1.002 × 10 −4 mg 2 cm −4 h −1 ), forming a predominantly chromia-based scale accompanied by discontinuous spinel and mixed M 2 O 3 oxides. A silica subscale was detected at the metal/oxide interface, and Laves-phase precipitates influenced oxidation by acting as diffusion barriers and local Si reservoirs. At 1000 °C, however, extensive scale cracking and spallation occurred after the shortest exposure time used in this study (24 h), hindering the establishment of a stable protective layer. Although chromia remained the main oxide, volatilization and mechanical degradation led to breakaway oxidation. The presence, distribution, and evolution of Laves-phase precipitates were found to strongly affect both diffusion processes and scale integrity. Overall, the alloy demonstrated promising high-temperature performance at 800 °C due to its lower mass variation and simple oxide scale formed during exposure compared to conventional stainless steels but insufficient resistance at 1000 °C, especially considering its higher cost, indicating potential applicability at intermediate temperatures.
- Open Access
- 12 February 2026
- Published by Elsevier in Corrosion Communications
Oxidation mechanisms and scale evolution in a novel Cr-Ni-Mn-based valve steel (X30CrNiMnNbN25-12)
- 12 February 2026
- Published by Elsevier in Corrosion Communications
Open AccessOxidation mechanisms and scale evolution in a novel Cr-Ni-Mn-based valve steel (X30CrNiMnNbN25-12)
- 26 September 2025
- Published by Elsevier in Corrosion Science
- Vol. 258
Exploring the influence of Nb content on high-temperature oxidation of NiTi shape memory alloys: Kinetics and Raman Spectroscopy study
- 26 September 2025
- Published by Elsevier in Corrosion Science
- Vol. 258
Exploring the influence of Nb content on high-temperature oxidation of NiTi shape memory alloys: Kinetics and Raman Spectroscopy study
- Open Access
- 28 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 4953-4964
Understanding the limited protectiveness of Si-rich passive film on Fe-based shape memory stainless steels in highly oxidizing media
- 28 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 4953-4964
Open AccessUnderstanding the limited protectiveness of Si-rich passive film on Fe-based shape memory stainless steels in highly oxidizing media
- Open Access
- 14 July 2025
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 6 (3) , 31
A Semi-Automated Image-Based Method for Interfacial Roughness Measurement Applied to Metal/Oxide Interfaces
Measuring interfacial roughness is essential in evaluating the adhesion of coatings and thermally grown oxides. Conventional contact methods are often impractical for such analyses, especially when the interface lies beneath a nonremovable layer. This study proposes a semi-automated method combining an ImageJ macro and an R-language script to assess interfacial roughness from images obtained through scanning electron microscopy (SEM), leveraging chemical contrast between substrate and oxide. The approach preserves user input where interpretation is critical while standardizing measurement to reduce variability. Applied to 21 images from seven experimental conditions, the algorithm successfully reproduced the roughness ranking obtained from manual measurement while also significantly reducing measurement dispersion. Though it underestimates absolute roughness values compared with the user measurements (which should also happen with conventional contact methods), it offers a robust, flexible, and reproducible alternative for interface characterization.
- 14 July 2025
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 6 (3) , 31
Open AccessA Semi-Automated Image-Based Method for Interfacial Roughness Measurement Applied to Metal/Oxide Interfaces
Measuring interfacial roughness is essential in evaluating the adhesion of coatings and thermally grown oxides. Conventional contact methods are often impractical for such analyses, especially when the interface lies beneath a nonremovable layer. This study proposes a semi-automated method combining an ImageJ macro and an R-language script to assess interfacial roughness from images obtained through scanning electron microscopy (SEM), leveraging chemical contrast between substrate and oxide. The approach preserves user input where interpretation is critical while standardizing measurement to reduce variability. Applied to 21 images from seven experimental conditions, the algorithm successfully reproduced the roughness ranking obtained from manual measurement while also significantly reducing measurement dispersion. Though it underestimates absolute roughness values compared with the user measurements (which should also happen with conventional contact methods), it offers a robust, flexible, and reproducible alternative for interface characterization.
- Open Access
Improvement of the Oxidation Resistance of FeMnSiCrNi Alloys with a Pre-Oxidation Treatment
Shape-memory Mn-rich austenitic stainless steels have a low high-temperature oxidation resistance because Mn tends to inhibit the formation of protective oxides. Mn depletion from oxidation also creates a ferritic Mn-depleted layer. A Mn-depleted layer formed via vacuum annealing has been associated with increased oxidation resistance. Thus, in the present study, a Mn-depleted layer was created with a pre-oxidation treatment conducted at 1000 °C for 30 min. Then, pre-treated and untreated samples were oxidized at 800 °C for up to 200 h. The resulting oxide layers were analyzed, as well as the metal/oxide interface roughness and the ferritic layer thickness. After pre-treatment, a 9 μm thick ferritic layer as well as an oxide layer richer in Cr-containing oxides than those usually observed in FeMnSiCrNi alloys oxidized at 800 °C were detected. After 200 h at 800 °C, the metal/oxide interface roughness of pre-treated samples was considerably lower. The oxidation rate of pre-treated samples was one order of magnitude lower for the first 50 h, but the effect significantly decreased afterward. The pre-existing ferritic layer was unable to stop Mn-rich oxides from being incorporated into the oxide layer, making its effect short-lived.
Open AccessImprovement of the Oxidation Resistance of FeMnSiCrNi Alloys with a Pre-Oxidation Treatment
Shape-memory Mn-rich austenitic stainless steels have a low high-temperature oxidation resistance because Mn tends to inhibit the formation of protective oxides. Mn depletion from oxidation also creates a ferritic Mn-depleted layer. A Mn-depleted layer formed via vacuum annealing has been associated with increased oxidation resistance. Thus, in the present study, a Mn-depleted layer was created with a pre-oxidation treatment conducted at 1000 °C for 30 min. Then, pre-treated and untreated samples were oxidized at 800 °C for up to 200 h. The resulting oxide layers were analyzed, as well as the metal/oxide interface roughness and the ferritic layer thickness. After pre-treatment, a 9 μm thick ferritic layer as well as an oxide layer richer in Cr-containing oxides than those usually observed in FeMnSiCrNi alloys oxidized at 800 °C were detected. After 200 h at 800 °C, the metal/oxide interface roughness of pre-treated samples was considerably lower. The oxidation rate of pre-treated samples was one order of magnitude lower for the first 50 h, but the effect significantly decreased afterward. The pre-existing ferritic layer was unable to stop Mn-rich oxides from being incorporated into the oxide layer, making its effect short-lived.
- 14 October 2023
- Published by Taylor & Francis in Disability and Rehabilitation: Assistive Technology
- Vol. 19 (6) , 2157-2165
Design and experimental validation of a new wheelchair seat stabilization system
Seat tilting wheelchair features can increase the comfort and safety of the user. Although many power wheelchairs have tilting mechanisms, they are often designed with a specific wheelchair model in mind. In this study, a design process for seat tilting mechanisms that can be applied to most rear-wheel drive wheelchair models is developed. Equations were developed to describe the geometrical and load constraints that were used to size the electric actuator that powers the system and define its position. Finally, the equations were used to create the seat tilting mechanism of a prototype wheelchair, which was then tested. The equations yielded coherent results which showed that advantageous actuator positions from a load minimization perspective usually require dimensions that cannot be found in commercial actuators. Also, there are positions in which the load increases exponentially, which should be avoided. The tests showed that the system was able to function properly on the prototype wheelchair and that the actuator position affected the time taken for the actuator to execute different parts of the tilting movement. The design process presented here was successful and modelled by general equations that can be applied to most front-wheel drive wheelchairs. It presents a low-cost option for the design of seat tilting systems, which can increase their accessibility.
- 14 October 2023
- Published by Taylor & Francis in Disability and Rehabilitation: Assistive Technology
- Vol. 19 (6) , 2157-2165
Design and experimental validation of a new wheelchair seat stabilization system
Seat tilting wheelchair features can increase the comfort and safety of the user. Although many power wheelchairs have tilting mechanisms, they are often designed with a specific wheelchair model in mind. In this study, a design process for seat tilting mechanisms that can be applied to most rear-wheel drive wheelchair models is developed. Equations were developed to describe the geometrical and load constraints that were used to size the electric actuator that powers the system and define its position. Finally, the equations were used to create the seat tilting mechanism of a prototype wheelchair, which was then tested. The equations yielded coherent results which showed that advantageous actuator positions from a load minimization perspective usually require dimensions that cannot be found in commercial actuators. Also, there are positions in which the load increases exponentially, which should be avoided. The tests showed that the system was able to function properly on the prototype wheelchair and that the actuator position affected the time taken for the actuator to execute different parts of the tilting movement. The design process presented here was successful and modelled by general equations that can be applied to most front-wheel drive wheelchairs. It presents a low-cost option for the design of seat tilting systems, which can increase their accessibility.
- Open Access
- 5 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 1281-1292
Ferritic layers formation mechanism during oxidation of FeMnSiCrNi alloys: Effect of temperature and influence on oxidation behavior
- 5 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 1281-1292
Open AccessFerritic layers formation mechanism during oxidation of FeMnSiCrNi alloys: Effect of temperature and influence on oxidation behavior
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 27 (3)
Influence of test parameters on the cyclic oxidation behavior of AISI 310 and a new Fe-5.9Si-3.9Cr-4.5Ni-0.8C (wt.%) alloy
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 27 (3)
Open AccessInfluence of test parameters on the cyclic oxidation behavior of AISI 310 and a new Fe-5.9Si-3.9Cr-4.5Ni-0.8C (wt.%) alloy