Joseph Andler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Joseph Andler has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Carol A. Handwerker
School of Materials Engineering, Purdue University, West Lafayette, USA
3 shared publications - Rakesh Agrawal
Davidson School of Chemical Engineering Purdue University West Lafayette Indiana USA
3 shared publications - Caitlyn M. Clarkson
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
2 shared publications Carol A. Handwerker
Purdue University
2 shared publicationsCarol Handwerker
2 shared publications- Congying Wang
School of Materials Engineering, Purdue University, West Lafayette, USA
2 shared publications
Latest Publications
- Open Access
- 6 November 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (19)
Tuning the optoelectronic properties of enargite (Cu3AsS4) solar cells by Ag alloying: A DFT-informed synthesis
The enargite phase of Cu3AsS4 (ENG) is an emerging photovoltaic material with a ∼1.4 eV bandgap and is composed of earth abundant elements with favorable defect properties arising from the differing ionic radii of the constituent elements. Unfortunately, ENG-based photovoltaic devices have experimentally been shown to have low power conversion efficiencies, possibly due to defects in the material. In this joint computational and experimental study, we explore the defect properties of ENG and employ synthesis approaches, such as silver alloying, to reduce the density of harmful defects. We show that shallow copper vacancies (VCu) are expected to be the primary defects in ENG and contribute to its p-type character. However, as shown through photoluminescence (PL) measurements of synthesized ENG, a large mid-bandgap PL peak is present at ∼0.87 eV from a band edge, potentially caused by a copper- or sulfur-related defect. To improve the properties of ENG films and mitigate the mid-bandgap PL, we employed an amine-thiol molecular precursor-based synthesis approach and utilized silver alloying of ENG films. While silver alloying did not affect the mid-bandgap PL peak, it increased grain size and lowered film porosity, improving device performance. In conclusion, we found that incorporating silver such that [Ag]/([Ag] + [Cu]) is 0.05 in the film using an amine-thiol based molecular precursor route with As2S3 as the arsenic source resulted in improved photovoltaic device performance with a champion device of efficiency 0.60%, the highest reported efficiency for an Cu3AsS4 (ENG)-based device to date.
- 6 November 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (19)
Open AccessTuning the optoelectronic properties of enargite (Cu3AsS4) solar cells by Ag alloying: A DFT-informed synthesis
The enargite phase of Cu3AsS4 (ENG) is an emerging photovoltaic material with a ∼1.4 eV bandgap and is composed of earth abundant elements with favorable defect properties arising from the differing ionic radii of the constituent elements. Unfortunately, ENG-based photovoltaic devices have experimentally been shown to have low power conversion efficiencies, possibly due to defects in the material. In this joint computational and experimental study, we explore the defect properties of ENG and employ synthesis approaches, such as silver alloying, to reduce the density of harmful defects. We show that shallow copper vacancies (VCu) are expected to be the primary defects in ENG and contribute to its p-type character. However, as shown through photoluminescence (PL) measurements of synthesized ENG, a large mid-bandgap PL peak is present at ∼0.87 eV from a band edge, potentially caused by a copper- or sulfur-related defect. To improve the properties of ENG films and mitigate the mid-bandgap PL, we employed an amine-thiol molecular precursor-based synthesis approach and utilized silver alloying of ENG films. While silver alloying did not affect the mid-bandgap PL peak, it increased grain size and lowered film porosity, improving device performance. In conclusion, we found that incorporating silver such that [Ag]/([Ag] + [Cu]) is 0.05 in the film using an amine-thiol based molecular precursor route with As2S3 as the arsenic source resulted in improved photovoltaic device performance with a champion device of efficiency 0.60%, the highest reported efficiency for an Cu3AsS4 (ENG)-based device to date.
- 28 January 2022
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 143
Analysis of enargite thin films synthesized from carbon-containing and novel carbon-free processing methods
- 28 January 2022
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 143
Analysis of enargite thin films synthesized from carbon-containing and novel carbon-free processing methods
- 5 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (7) , 3195-3199
BEOL Compatible Indium-Tin-Oxide Transistors: Switching of Ultrahigh-Density 2-D Electron Gas Over 0.8 × 1014/cm2 at Oxide/Oxide Interface by the Change of Ferroelectric Polarization
In this work, we report back-end-of-line (BEOL) compatible indium-tin-oxide (ITO) transistors with ferroelectric (FE) Hf0.5Zr0.5O2 (HZO) as gate insulator. A tunable high-density 2-D electron gas over 0.8 x 10¹⁴/cm² is achieved at the HZO/ITO oxide/oxide interface because of the FE polarization, which is confirmed by I-V, positive up and negative down (PUND), and Hall measurements. Such high carrier density can be completely modulated and switched on and off by FE polarization switching, enabling high mobility ITO transistor with high on-current and high on/off ratio.
- 5 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (7) , 3195-3199
BEOL Compatible Indium-Tin-Oxide Transistors: Switching of Ultrahigh-Density 2-D Electron Gas Over 0.8 × 1014/cm2 at Oxide/Oxide Interface by the Change of Ferroelectric Polarization
In this work, we report back-end-of-line (BEOL) compatible indium-tin-oxide (ITO) transistors with ferroelectric (FE) Hf0.5Zr0.5O2 (HZO) as gate insulator. A tunable high-density 2-D electron gas over 0.8 x 10¹⁴/cm² is achieved at the HZO/ITO oxide/oxide interface because of the FE polarization, which is confirmed by I-V, positive up and negative down (PUND), and Hall measurements. Such high carrier density can be completely modulated and switched on and off by FE polarization switching, enabling high mobility ITO transistor with high on-current and high on/off ratio.
- 24 August 2020
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 14 (9) , 11542-11547
Indium–Tin-Oxide Transistors with One Nanometer Thick Channel and Ferroelectric Gating
In this work, we demonstrate high-performance indium–tin-oxide (ITO) transistors with a channel thickness down to 1 nm and ferroelectric Hf0.5Zr0.5O2 as gate dielectric. An on-current of 0.243 A/mm is achieved on submicron gate-length ITO transistors with a channel thickness of 1 nm, while it increases to as high as 1.06 A/mm when the channel thickness increases to 2 nm. A raised source/drain structure with a thickness of 10 nm is employed, contributing to a low contact resistance of 0.15 Ω·mm and a low contact resistivity of 1.1 × 10–7 Ω·cm2. The ITO transistor with a recessed channel and ferroelectric gating demonstrates several advantages over 2D semiconductor transistors and other thin-film transistors, including large-area wafer-size nanometer thin-film formation, low contact resistance and contact resistivity, an atomic thin channel being immune to short channel effects, large gate modulation of high carrier density by ferroelectric gating, high-quality gate dielectric and passivation formation, and a large bandgap for the low-power back-end-of-line complementary metal-oxide-semiconductor application.
- 24 August 2020
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 14 (9) , 11542-11547
Indium–Tin-Oxide Transistors with One Nanometer Thick Channel and Ferroelectric Gating
In this work, we demonstrate high-performance indium–tin-oxide (ITO) transistors with a channel thickness down to 1 nm and ferroelectric Hf0.5Zr0.5O2 as gate dielectric. An on-current of 0.243 A/mm is achieved on submicron gate-length ITO transistors with a channel thickness of 1 nm, while it increases to as high as 1.06 A/mm when the channel thickness increases to 2 nm. A raised source/drain structure with a thickness of 10 nm is employed, contributing to a low contact resistance of 0.15 Ω·mm and a low contact resistivity of 1.1 × 10–7 Ω·cm2. The ITO transistor with a recessed channel and ferroelectric gating demonstrates several advantages over 2D semiconductor transistors and other thin-film transistors, including large-area wafer-size nanometer thin-film formation, low contact resistance and contact resistivity, an atomic thin channel being immune to short channel effects, large gate modulation of high carrier density by ferroelectric gating, high-quality gate dielectric and passivation formation, and a large bandgap for the low-power back-end-of-line complementary metal-oxide-semiconductor application.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1669-1674
Assessing the Potential Environmental Impact of Cu3AsS4 PV Systems
Cu3AsS4 solar cells have gained recent attention as a promising single-junction solar absorber. As arsenic is a constituent element of Cu3AsS4, there is concern over its potential life cycle impacts. In this work, we establish a basis for assessing the potential life cycle impacts of this technology by completing a cradle-to-grave life cycle assessment (LCA) as well as an evaluation of Cu3AsS4 solar cell leaching characteristics through a scaled toxicity characteristic leaching procedure (TCLP). We conclude that, within the system boundary, arsenic contributes minimally to the life cycle impacts compared to BOS components and product performance.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1669-1674
Assessing the Potential Environmental Impact of Cu3AsS4 PV Systems
Cu3AsS4 solar cells have gained recent attention as a promising single-junction solar absorber. As arsenic is a constituent element of Cu3AsS4, there is concern over its potential life cycle impacts. In this work, we establish a basis for assessing the potential life cycle impacts of this technology by completing a cradle-to-grave life cycle assessment (LCA) as well as an evaluation of Cu3AsS4 solar cell leaching characteristics through a scaled toxicity characteristic leaching procedure (TCLP). We conclude that, within the system boundary, arsenic contributes minimally to the life cycle impacts compared to BOS components and product performance.
- 29 June 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (28) , 6913-6916
Solution-processed copper arsenic sulfide thin films for photovoltaic applications
The first thin films of novel semiconductor Cu 3 AsS 4 are synthesized through solution-based methods and display promise for photovoltaic applications.
- 29 June 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (28) , 6913-6916
Solution-processed copper arsenic sulfide thin films for photovoltaic applications
The first thin films of novel semiconductor Cu 3 AsS 4 are synthesized through solution-based methods and display promise for photovoltaic applications.