Oleksandr Bilohub
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oleksandr Bilohub has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ihor Romanenko
National Aerospace University “Kharkiv Aviation Institute”, Kharkiv
2 shared publications - Serhiy Kryhin
National Aerospace University "Kharkiv Aviation Institute
1 shared publication - Yurii Husiev
National Aerospace University "Kharkiv Aviation Institute", Kharkiv
1 shared publication - Yuriy Torba
SE “Ivchenko-Progress”, Zaporizhzhia, Ukraine
1 shared publication Олександр Володимирович Гудошник
Національний аерокосмічний університет ім. М. Є. Жуковського «Харківський авіаційний інститут», Харків
1 shared publicationСергій Олександрович Тристан
Національний аерокосмічний університет ім. М. Є. Жуковського «Харківський авіаційний інститут», Харків
1 shared publication
Latest Publications
- Open Access
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 119-124
Похибки передачі відносних деформацій у тензометричному пристрої при підвищеній температурі
The subject of study in this article is the distribution of relative deformations in the system of the strain gauge used in the study. This study aims to identify factors and study their influence on the accuracy of measuring relative deformations. Task: to conduct a simulation of the distribution of deformations to assess the distortions caused by the ineffective transfer of stresses through the bonding layer, and to study the influence of design factors on the measurement error. Obtaining reliable data and making adjustments from a strain gauge of increased thickness operating in high-temperature conditions. Method for solving the problem: computational and analytical. Thus, the results of the computational experiment demonstrate the high efficiency of the developed strain gauge device, particularly under significant temperature gradients. The key factor ensuring this efficiency is not only a stable strain transfer coefficient, which minimizes the influence of external factors on the accuracy of measurements, but also effective leveling of the thermally caused additive error. This process is achieved by the mutual arrangement of strain gauges and the use of a high-temperature insulator-connector material. The obtained data emphasize the potential of using the device in environments with unstable thermal conditions, where accurate deformation measurements are critical for ensuring reliable operation and monitoring the condition of the parts under study. Conclusions. The deformation characteristics of the strain gauge device installed on the part model were investigated using computational experiment methods when heat flow was applied and loaded. The sensitive elements perceive the deformation from the part at the level of 96%. The research results have theoretical and practical significance for increasing the accuracy of research at elevated temperatures and the possibility of making corrections to the measurement results if necessary. Further research and improvement of the strain gauge device are proposed, and the advantages of the used technical solution are analyzed.
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 119-124
Open AccessПохибки передачі відносних деформацій у тензометричному пристрої при підвищеній температурі
The subject of study in this article is the distribution of relative deformations in the system of the strain gauge used in the study. This study aims to identify factors and study their influence on the accuracy of measuring relative deformations. Task: to conduct a simulation of the distribution of deformations to assess the distortions caused by the ineffective transfer of stresses through the bonding layer, and to study the influence of design factors on the measurement error. Obtaining reliable data and making adjustments from a strain gauge of increased thickness operating in high-temperature conditions. Method for solving the problem: computational and analytical. Thus, the results of the computational experiment demonstrate the high efficiency of the developed strain gauge device, particularly under significant temperature gradients. The key factor ensuring this efficiency is not only a stable strain transfer coefficient, which minimizes the influence of external factors on the accuracy of measurements, but also effective leveling of the thermally caused additive error. This process is achieved by the mutual arrangement of strain gauges and the use of a high-temperature insulator-connector material. The obtained data emphasize the potential of using the device in environments with unstable thermal conditions, where accurate deformation measurements are critical for ensuring reliable operation and monitoring the condition of the parts under study. Conclusions. The deformation characteristics of the strain gauge device installed on the part model were investigated using computational experiment methods when heat flow was applied and loaded. The sensitive elements perceive the deformation from the part at the level of 96%. The research results have theoretical and practical significance for increasing the accuracy of research at elevated temperatures and the possibility of making corrections to the measurement results if necessary. Further research and improvement of the strain gauge device are proposed, and the advantages of the used technical solution are analyzed.
- Open Access
- 2 September 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 1,p. 12-16
PROFILING THE SURFACE OF THE PIN HOLE IN THE PISTON BODY
Minimization of the mass of the piston kit, which consists of three main parts - piston, pin and connecting rod, is connected, among other things, with the possibility of reducing the diameter of the steel pin. On the other hand, a decrease in its diameter inevitably leads to an increase in stresses in the piston pin hole (PPH) and possible destruction. It is known that reducing the mass of the piston set from 5 to 20% leads to an increase in the output parameters of the internal combustion engine - torque and power by 1% to 4.5%. The purpose of the study is to determine the possibility of reducing the stresses in the bearing due to the profiling of its surface while reducing the diameter of the piston pin. The research algorithm is presented, which consists of building a geometric model of the piston assembly, loading with excessive pressure taking into account the plasticity of the material, modifying the geometry of the PPH and checking the stresses of the loaded state. The conventional piston model has the following geometry: diameter – 80 mm; height – 60 mm; compression height – 30 mm; the diameter of the finger hole is 18 mm; the distance between the bumps is 28 mm. Piston material – aluminum-based alloy – AISI 2014-0, pin and connecting rod material – AISI 1020 steel. Pressure loading conditions: taking into account plasticity – nonlinear, harmonic, 2 cycles, maximum amplitude – 8 MPa; test - static, 6.5 MPa. A crumpling zone with residual deformations was detected in the PPH, the maximum final deformation practically does not differ in the first and second load cycles (0.0081 vs. 0.0084). Residual deformations occur 1/3 of the length from the inner edge of the head. The absolute residual deformations are given in the form of a sweep of the change in the PPH radius. The maximum value is about 0.04 mm. This result is the basis for modifying the geometry of the surface of the finger hole. The modified geometry of the PPH is obtained by boring the cylindrical surface with a profile modeled by the appropriate spline on the geometric model. The boring axis is offset by 0.02 mm from the PPH axis. Verification modeling showed that the averaged loads on the edge of the model are 143 MPa for the cylindrical and 107 MPa for the modified PPH (-25% for the modified profile).
- 2 September 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 1,p. 12-16
Open AccessPROFILING THE SURFACE OF THE PIN HOLE IN THE PISTON BODY
Minimization of the mass of the piston kit, which consists of three main parts - piston, pin and connecting rod, is connected, among other things, with the possibility of reducing the diameter of the steel pin. On the other hand, a decrease in its diameter inevitably leads to an increase in stresses in the piston pin hole (PPH) and possible destruction. It is known that reducing the mass of the piston set from 5 to 20% leads to an increase in the output parameters of the internal combustion engine - torque and power by 1% to 4.5%. The purpose of the study is to determine the possibility of reducing the stresses in the bearing due to the profiling of its surface while reducing the diameter of the piston pin. The research algorithm is presented, which consists of building a geometric model of the piston assembly, loading with excessive pressure taking into account the plasticity of the material, modifying the geometry of the PPH and checking the stresses of the loaded state. The conventional piston model has the following geometry: diameter – 80 mm; height – 60 mm; compression height – 30 mm; the diameter of the finger hole is 18 mm; the distance between the bumps is 28 mm. Piston material – aluminum-based alloy – AISI 2014-0, pin and connecting rod material – AISI 1020 steel. Pressure loading conditions: taking into account plasticity – nonlinear, harmonic, 2 cycles, maximum amplitude – 8 MPa; test - static, 6.5 MPa. A crumpling zone with residual deformations was detected in the PPH, the maximum final deformation practically does not differ in the first and second load cycles (0.0081 vs. 0.0084). Residual deformations occur 1/3 of the length from the inner edge of the head. The absolute residual deformations are given in the form of a sweep of the change in the PPH radius. The maximum value is about 0.04 mm. This result is the basis for modifying the geometry of the surface of the finger hole. The modified geometry of the PPH is obtained by boring the cylindrical surface with a profile modeled by the appropriate spline on the geometric model. The boring axis is offset by 0.02 mm from the PPH axis. Verification modeling showed that the averaged loads on the edge of the model are 143 MPa for the cylindrical and 107 MPa for the modified PPH (-25% for the modified profile).
- Open Access
- 15 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 2,p. 20-25
PROFILING OF THE OUTER SURFACE OF THE PISTON
The piston is one of the main resource-intensive and knowledge-intensive parts of the internal combustion engine. Its design significantly affects almost all indicators of the perfection of the power plant with internal combustion engines as a whole. A correctly designed profile is the main parameter that allows the engine to blow safely during the first starts. The development, production and use of pistons in the primary and secondary markets is impossible without appropriate scientific research that will increase the design and technological capabilities of all interested parties. Pistons for gasoline internal combustion engines of passenger cars will continue to dominate the markets, which is connected with the greening of transport as a whole. This emphasizes the importance of research on the improvement of positive-ignition internal combustion engine pistons. Rational profiling of the outer surface is an important task for improving the design of the piston. The diagram of the design creation technology, which was adopted by JSC "AVTRAMAT" (Kharkiv Plant "Porshen") as the standard of the enterprise, according to which pistons were created, which were then supplied to factories of the engine-building industry and for spare parts, is given. The profiles of the side surfaces of the pistons of automobile internal combustion engines, which were designed and implemented in production, were analyzed. The analysis was carried out for pistons with a diameter of 72 to 100 mm and a height of 45 to 73 mm. It is shown that the given profiles of the side surfaces in these pistons are geometrically similar both along and perpendicular to its axis. It is shown that the geometric shape of the profile can be described by polynomials of the 3rd and 4th degree, which allows for easy further use. This can be used when designing the profiles of future structures. Formulas and an algorithm are given, according to which it is possible to calculate the external profile of pistons of automobile reciprocating internal combustion engines according to 2 parameters - diameter and height.
- 15 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 2,p. 20-25
Open AccessPROFILING OF THE OUTER SURFACE OF THE PISTON
The piston is one of the main resource-intensive and knowledge-intensive parts of the internal combustion engine. Its design significantly affects almost all indicators of the perfection of the power plant with internal combustion engines as a whole. A correctly designed profile is the main parameter that allows the engine to blow safely during the first starts. The development, production and use of pistons in the primary and secondary markets is impossible without appropriate scientific research that will increase the design and technological capabilities of all interested parties. Pistons for gasoline internal combustion engines of passenger cars will continue to dominate the markets, which is connected with the greening of transport as a whole. This emphasizes the importance of research on the improvement of positive-ignition internal combustion engine pistons. Rational profiling of the outer surface is an important task for improving the design of the piston. The diagram of the design creation technology, which was adopted by JSC "AVTRAMAT" (Kharkiv Plant "Porshen") as the standard of the enterprise, according to which pistons were created, which were then supplied to factories of the engine-building industry and for spare parts, is given. The profiles of the side surfaces of the pistons of automobile internal combustion engines, which were designed and implemented in production, were analyzed. The analysis was carried out for pistons with a diameter of 72 to 100 mm and a height of 45 to 73 mm. It is shown that the given profiles of the side surfaces in these pistons are geometrically similar both along and perpendicular to its axis. It is shown that the geometric shape of the profile can be described by polynomials of the 3rd and 4th degree, which allows for easy further use. This can be used when designing the profiles of future structures. Formulas and an algorithm are given, according to which it is possible to calculate the external profile of pistons of automobile reciprocating internal combustion engines according to 2 parameters - diameter and height.
- Open Access
- 24 April 2023
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 38-45
Підвищення ефективності робочого циклу паливного шестерного насоса високого тиску за рахунок використання струминного насоса в якості ступеня підкачування
This article analyzes the possibility of increasing the efficiency of the gear pump operating cycle by using a jet pump as a booster stage. The design of gear pumps is performed for one mode, and most often, it is a mode with minimum speed and high consumption relative to rotation speed. For gas turbine engines, this is the take-off mode, in which the aircraft operates for a few minutes of the entire flight cycle. In other modes, the pump capacity is excessive, reaching more than twice the value in some operational conditions. Due to the excess capacity, overflow valves are used to synchronize the operation of the engine and pump. This approach is a classic solution, but it creates additional mechanical losses and, as a result, reduces the efficiency of the operating cycle of the pump. Therefore, there is a need to improve the matching of engine requirements and pump performance. In this article, a solution that can improve the operating cycle of pumping units within the framework of a classical drive box assembly was analyzed. In the introductory section, the generalized flight cycle of a transport aircraft is analyzed. Based on the results, the modes were determined for which the design calculations of the jet pump were performed. First, the relative characteristics of pressure increase and efficiency are considered. The geometric and operational boundary conditions are accepted considering the fuel overflow relative to the generalized flight cycle. The obtained characteristics are used as a basis for selecting the geometric ratio for the modes with the highest pressure and efficiency. Based on these results, the geometric dimensions of the main sections and the value of the pressure increase at the outlet of the jet pump were obtained. Based on the characteristics of the pressure increase behind the jet pump, the relative characteristics of the reduction in power consumption in the gear pump shaft were obtained. Considering the level of overflow and operating time, the use of a jet pump will save about 50% of the energy input. This is a direct improvement in the operating cycle, and the increased pump inlet pressure will also reduce bearing wear, increase cavitation resistance, and reduce wear from cavitation erosion.
- 24 April 2023
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 38-45
Open AccessПідвищення ефективності робочого циклу паливного шестерного насоса високого тиску за рахунок використання струминного насоса в якості ступеня підкачування
This article analyzes the possibility of increasing the efficiency of the gear pump operating cycle by using a jet pump as a booster stage. The design of gear pumps is performed for one mode, and most often, it is a mode with minimum speed and high consumption relative to rotation speed. For gas turbine engines, this is the take-off mode, in which the aircraft operates for a few minutes of the entire flight cycle. In other modes, the pump capacity is excessive, reaching more than twice the value in some operational conditions. Due to the excess capacity, overflow valves are used to synchronize the operation of the engine and pump. This approach is a classic solution, but it creates additional mechanical losses and, as a result, reduces the efficiency of the operating cycle of the pump. Therefore, there is a need to improve the matching of engine requirements and pump performance. In this article, a solution that can improve the operating cycle of pumping units within the framework of a classical drive box assembly was analyzed. In the introductory section, the generalized flight cycle of a transport aircraft is analyzed. Based on the results, the modes were determined for which the design calculations of the jet pump were performed. First, the relative characteristics of pressure increase and efficiency are considered. The geometric and operational boundary conditions are accepted considering the fuel overflow relative to the generalized flight cycle. The obtained characteristics are used as a basis for selecting the geometric ratio for the modes with the highest pressure and efficiency. Based on these results, the geometric dimensions of the main sections and the value of the pressure increase at the outlet of the jet pump were obtained. Based on the characteristics of the pressure increase behind the jet pump, the relative characteristics of the reduction in power consumption in the gear pump shaft were obtained. Considering the level of overflow and operating time, the use of a jet pump will save about 50% of the energy input. This is a direct improvement in the operating cycle, and the increased pump inlet pressure will also reduce bearing wear, increase cavitation resistance, and reduce wear from cavitation erosion.
- 28 April 2021
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 52-58
Працездатність підшипників ковзання як опор шестерень основного паливного насосу ГТД
The paper is about the performance capability of the journal bearings as a support of the fuel gear pump for gas turbine engines (GTE). Supports of the external gear pump usually operate in semi-dry friction conditions, which reduces residual life and is one of the limiting factors. For this investigation, the serial gear pump was chosen with the following parameters: the number of teeth z = 14, module m = 3.8, gear-loading Р = 7800 N. The authors have studied options for a pump with an electrical and mechanical (from the rotor of the GTE) drive. The main criterion for studying the bearing capacity is the minimum thickness of the working layer of a fluid with low viscosity (kerosene). For modeling, a common theory is used based on solutions of differential equations of the viscous fluid hydrodynamics, which relate pressure, velocity, and viscous shear resistance. For technological reasons, the minimum allowable kerosene layer is limited to 5 μm. The conducted analysis considers the multi-lobe (2-, 3- and 4-lobe) bearings with different lobe orientations relative to the force vector. It was found that the 2-lobe bearing has the best load capacity (provides the largest layer of kerosene). According to the results of the previous investigation for further work, the 2-lobe bearing was chosen. The influence of load, setting gap, eccentricity, the specific radius of lobe curvature, shaft length on the bearing load capacity was analyzed. A rational type of bearing design was proposed based on the load capacity criterion (the minimum layer of working fluid). It was shown that the hydrodynamic 2-lobe bearing can be sufficiently effective for the supports of the gear fuel pumps of GTE. Based on the results of the investigation, 2 variants of the pumping unit designs were proposed. The first one for the pump driven by the gas turbine engine rotor with parameters z = 19, m = 3.3, gears width B = 34, shaft diameter DS = 48, and shaft length LS = 56 (P = 10.2kN). The second one for the electrically driven pump, z = 28, m = 1,8, B = 15, DS = 34, and LS = 41 (P = 3.8 kN). The minimum angular velocity for the pump variants is 470 and 1055 rad/s, respectively. According to the investigation results, it was proposed to conduct related studies of the working process in pumps and bearings.
- 28 April 2021
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 52-58
Працездатність підшипників ковзання як опор шестерень основного паливного насосу ГТД
The paper is about the performance capability of the journal bearings as a support of the fuel gear pump for gas turbine engines (GTE). Supports of the external gear pump usually operate in semi-dry friction conditions, which reduces residual life and is one of the limiting factors. For this investigation, the serial gear pump was chosen with the following parameters: the number of teeth z = 14, module m = 3.8, gear-loading Р = 7800 N. The authors have studied options for a pump with an electrical and mechanical (from the rotor of the GTE) drive. The main criterion for studying the bearing capacity is the minimum thickness of the working layer of a fluid with low viscosity (kerosene). For modeling, a common theory is used based on solutions of differential equations of the viscous fluid hydrodynamics, which relate pressure, velocity, and viscous shear resistance. For technological reasons, the minimum allowable kerosene layer is limited to 5 μm. The conducted analysis considers the multi-lobe (2-, 3- and 4-lobe) bearings with different lobe orientations relative to the force vector. It was found that the 2-lobe bearing has the best load capacity (provides the largest layer of kerosene). According to the results of the previous investigation for further work, the 2-lobe bearing was chosen. The influence of load, setting gap, eccentricity, the specific radius of lobe curvature, shaft length on the bearing load capacity was analyzed. A rational type of bearing design was proposed based on the load capacity criterion (the minimum layer of working fluid). It was shown that the hydrodynamic 2-lobe bearing can be sufficiently effective for the supports of the gear fuel pumps of GTE. Based on the results of the investigation, 2 variants of the pumping unit designs were proposed. The first one for the pump driven by the gas turbine engine rotor with parameters z = 19, m = 3.3, gears width B = 34, shaft diameter DS = 48, and shaft length LS = 56 (P = 10.2kN). The second one for the electrically driven pump, z = 28, m = 1,8, B = 15, DS = 34, and LS = 41 (P = 3.8 kN). The minimum angular velocity for the pump variants is 470 and 1055 rad/s, respectively. According to the investigation results, it was proposed to conduct related studies of the working process in pumps and bearings.