HPHaiyang Pan

Haiyang Pan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Haiyang Pan has a total of 20 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Stress Sensitivity of Tight Sandstone Reservoirs Under the Effect of Pore Structure Heterogeneity

    by Haiyang Pan, Yun Du, Qingling Zuo, Zhiqing Xie, Yao Zhou, Anan Xu, Junjian Zhang, Yuqiang Guo

    The effect of the pore–fracture structure on the porosity and permeability affects the production process of tight sandstone gas. In this paper, 12 groups of tight sandstone samples are selected as the object, and the pore–fracture volume of a tight reservoir is quantitatively characterized by a high-pressure mercury injection test. The multifractal and single fractal characteristics of different types of samples are calculated by fractal theory. On this basis, the pore volume variation under stress is discussed through the overlying pressure pore permeability test, and the pore–fracture compressibility is calculated. Finally, the main factors affecting the stress sensitivity of tight sandstone are summarized from the two aspects of the pore structure and mineral composition. The results are as follows. (1) The samples could be divided into types A and B by using the mercury-in and mercury-out curves. There is a significant hysteresis loop in the mercury inlet and outlet curves of type A, and the efficiency of the mercury inlet and outlet in the pores is relatively higher. The mercury removal curve of type B is almost parallel, and its mercury removal efficiency is relatively lower. (2) The applicability of singlet fractals in characterizing the heterogeneity of micropores is higher than that of multifractals. This is because the single fractal characteristics of the two types of samples have significant differences, while the differences in the multifractals are relatively weak. (3) A pore diameter of 100–1000 nm provides the main compression space for the type A samples. A pore distribution heterogeneity of 100–1000 nm affects the compression effect and stress sensitivity of this type B sample.


  • Open Access

    A Physical Parameter Characterizing Heterogeneity of Pore and Fracture Structures in Coal Reservoirs

    by Haiyang Pan, Yinchuan Shao, Zhizheng Liu, Qingling Zuo, Jitong Su, Jianglun Bai, Heyao Miao, Yuqiang Guo, Junjian Zhang

    Pore structure heterogeneity of coal reservoirs restricts the diffusion-seepage process of coalbed methane, thereby restricting the production capacity of coalbed methane. Therefore, 10 coal samples from the Linxing area are taken as an objective, and high-pressure mercury intrusion testing was used to describe the pore structure distribution of all the coal samples. On this basis, four single and multifractal models were used to perform fractal calculations, and correlation analysis was conducted on the mercury advance and retreat fractal dimension values to clarify the physical significance of mercury removal fractal dimension values. Finally, the relationship between fractal dimension values of mercury curves and pore structure parameters was clarified, and the applicability of various fractal models in characterizing pore structure heterogeneity was explored. All the samples can be divided into type A and B by using pore volume percentage greater than 1000 nm and the mercury removal efficiency. The T model has universality and the strongest correlation in characterizing the heterogeneity of pore volume distribution in samples. A fractal parameter based on high-pressure mercury injection curve was obtained, and was then used to quantitatively characterize the pore and fracture structure of coal reservoirs. This parameter is used to characterize the complexity of gas and water transport during coalbed methane production, further elucidating the coalbed methane production process under the constraint of pore and fracture structure in coal reservoirs.


  • Open Access

    Monitoring and Assessment of Cemented Paste Backfill Containing Coal Gangue and Fly Ash in an Underground Mine

    by Xinguo Zhang, Jinhai Zhao, Lin Xin, Kun Wang, Haiyang Pan

    Cemented coal gangue paste backfill (CCGPB) containing coal gangue and fly ash is a backfilling technique newly developed in coal mines in China that allows environmentally hazardous products, such as gangue and fly ash, to be reused in underground stopes. CCGPB materials provide efficient ground support for the caving of strata and reduce surface subsidence. In this paper, field monitoring of CCGPB properties was conducted in an underground coal mine, which mainly included the measurement of the longwall face temperature, humidity, CCGPB internal hydration temperature, stress conditions inside the backfills, and displacement. First, the components of the backfills, paste technique, slurry generation procedures, coalfield geology, and mining conditions were introduced. Then, a monitoring system was designed in the field. An online monitoring system was installed. The results of the field monitoring showed that the curing temperature significantly varied, i.e., from 26°C near the main gate to 37°C near the tailgate. The curing humidity had the same trends, increasing from 60% relative humidity (RH) near the main gate to 81% RH near the tailgate. The internal hydration process of the paste was divided into four stages, i.e., the rapid hydration stage, slower hydration stage, rapid decline hydration stage, and relatively stable stage. The highest hydration temperature was 50°C, which was measured on the second day after the backfill process. The temperature approached stability at 41°C. The evolution of the roof stress applied on the CCGPB was divided into four stages: the development stage, regulation stage, rapid growth stage, and relatively stable stage. The maximum roof loading was 12 MPa in the middle of the longwall face. The deformation of the backfill experienced four stages, i.e., the rapid deformation stage, slow deformation stage, relatively stable stage, and long‐term stable stage. The maximum deformation was 104.3 mm, appearing in the middle of the face. In addition, the compression ratio of the backfill was approximately 4%. The results of this study showed that the working conditions of backfills in the field were different from those in the laboratory. This paper provides guidance for the design of the CCGPB technique and the predictions of surface subsidence induced by the production process of underground mining.


  • Open Access

    Crack Initiation Behaviors of Granite Specimens Containing Crossing‐Double‐Flaws with Different Lengths under Uniaxial Loading

    by Haiyang Pan, Dawei Yin, Ning Jiang, Zhiguo Xia

    Crack initiation is an important stage in the failure process of rock masses. In this paper, crack initiation behaviors (crack initiation model, crack initiation location, crack initiation angle, and crack initiation stress) of granite specimens containing crossing‐double‐flaws with different lengths were investigated using PFC2D software. Crack initiation models were all tensile wing cracks, which did not exactly initiate from the main flaw with a length of 30 mm. They can initiate from the secondary flaw with a length 20 mm at α of 30° (included angle between main flaw and horizontal direction) and β of 90° (included angle between main and secondary flaws) and from main and secondary flaws at α of 30° and β of 60°. These were mainly induced by the superposition of stress fields around the main and secondary flaws as β varied from 0° to 90°, especially the tensile force concentration zones superposition. The tensile forces concentration zone around flaw shrank towards flaw tips with the increase of flaw’s inclinations measured horizontally. Under stress field superposition effects, the crack initiation stress decreased firstly and then increased with β at α of 30° and 45°. Crack initiation locations were close to flaw tips but not restricted to them. The distances between crack initiation locations and flaw tips, and the crack initiation angles depended on the flaw where first macrocracks initiated from. Microdisplacement field distributions of granite specimens to reveal the mesomechanism of crack initiation behaviors were discussed.