Giorgio Santarelli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giorgio Santarelli has a total of 324 co-authors. Here are the top co-authors by number of shared publications:
Germain Guiraud
TOPTICA Photonics France
17 shared publicationsNicholas Traynor
TOPTICA Photonics France
16 shared publicationsA. Clairon
SYRTE - Systèmes de Référence Temps Espace (61 Av de l'Observatoire 75014 PARIS - France)
15 shared publications- Anne Amy-Klein
Université Sorbonne Paris Nord
10 shared publications - Stefano Barbieri
Institute of Electronics, Microelectronics and Nanotechnology, CNRS, Univ. Lille, Univ. Polytechnique Hauts-de-France
10 shared publications Christian Chardonnet
Laboratoire de Physique des Lasers, Université Paris 13, Sorbonne Paris Cité, CNRS, Villetaneuse, France
9 shared publications
Latest Publications
- 30 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2696-2699
High-power, 420-nm, low-intensity-noise laser source for quantum computing applications
We demonstrate the generation of 20.2 W of continuous-wave, low-intensity noise, single-frequency light at 840 nm, obtained via sum-frequency mixing of two high-power infrared fiber laser systems in an MgO-doped periodically poled lithium niobate (ppLN) crystal. Subsequent cavity-enhanced frequency doubling to 420 nm yields an output power of 15.2 W. Respective conversion efficiencies of 48% and 79% are achieved for the sum-frequency and second-harmonic stages, with good beam quality (M 2 < 1.3), low intensity noise (<0.05% RMS [1 kHz–10 MHz]), and long-term continuous operation. Relative intensity noise and frequency noise of the generated signals are experimentally characterized.
- 30 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2696-2699
High-power, 420-nm, low-intensity-noise laser source for quantum computing applications
We demonstrate the generation of 20.2 W of continuous-wave, low-intensity noise, single-frequency light at 840 nm, obtained via sum-frequency mixing of two high-power infrared fiber laser systems in an MgO-doped periodically poled lithium niobate (ppLN) crystal. Subsequent cavity-enhanced frequency doubling to 420 nm yields an output power of 15.2 W. Respective conversion efficiencies of 48% and 79% are achieved for the sum-frequency and second-harmonic stages, with good beam quality (M 2 < 1.3), low intensity noise (<0.05% RMS [1 kHz–10 MHz]), and long-term continuous operation. Relative intensity noise and frequency noise of the generated signals are experimentally characterized.
- Open Access
- 2 January 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (1) , 433-446
Sub-100-fs pulses at 1030 nm with THz repetition rate using dual-frequency beat compression in photonic crystal fiber
We demonstrate the generation of femtosecond pulse trains at 1030 nm with repetition rates tunable from 330 GHz to 1 THz in a fully polarization-maintaining (PM) fiber system. Two detuned single-frequency lasers create a dual-frequency optical beat signal that undergoes strong nonlinear evolution in a PM photonic crystal fiber (PM-PCF) pumped in the anomalous dispersion regime, producing pulses with durations ranging from about 120 fs down to 60 fs without external post-compression. To deliver the required peak power, the dual-frequency signal is carved into 1-ns-long bursts at a repetition rate of 1 MHz. The nonlinear propagation is well described by breather theory. At higher input powers, the breathers evolve into Raman-shifted fundamental solitons, whose self-frequency shift and noise-driven dynamics are confirmed experimentally and numerically. These results highlight the versatility of the dual-pump scheme and the rich nonlinear dynamics of PM-PCFs, establishing a route toward compact sources of tunable, ultra-high-repetition-rate short pulses.
- 2 January 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (1) , 433-446
Open AccessSub-100-fs pulses at 1030 nm with THz repetition rate using dual-frequency beat compression in photonic crystal fiber
We demonstrate the generation of femtosecond pulse trains at 1030 nm with repetition rates tunable from 330 GHz to 1 THz in a fully polarization-maintaining (PM) fiber system. Two detuned single-frequency lasers create a dual-frequency optical beat signal that undergoes strong nonlinear evolution in a PM photonic crystal fiber (PM-PCF) pumped in the anomalous dispersion regime, producing pulses with durations ranging from about 120 fs down to 60 fs without external post-compression. To deliver the required peak power, the dual-frequency signal is carved into 1-ns-long bursts at a repetition rate of 1 MHz. The nonlinear propagation is well described by breather theory. At higher input powers, the breathers evolve into Raman-shifted fundamental solitons, whose self-frequency shift and noise-driven dynamics are confirmed experimentally and numerically. These results highlight the versatility of the dual-pump scheme and the rich nonlinear dynamics of PM-PCFs, establishing a route toward compact sources of tunable, ultra-high-repetition-rate short pulses.
- Open Access
- 22 July 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (15) , 32061-32071
50 W low-noise single-frequency thulium-doped fiber amplifier at 1844 nm
In this work, we present a 50 W laser amplifier architecture operating at 1844 nm, encompassing a three-stage amplification architecture. The first two stages rely on core-pumping, while the final stage employs high-power cladding pumping. Core-pumping at 1560 nm enables a tunable output power of 2 W between 1830 nm and 1880 nm at the output of the second preamplifier. An integrated spectral filter comprising a circulator and a fiber Bragg grating (FBG) centered at 844 nm is used. Cladding pumping at 793 nm is implemented for power scaling, achieving over 50 W of output power with an optical signal-to-noise ratio (OSNR) exceeding 60 dB. The amplifier exhibits low intensity noise, with an RMS noise of 0.006% in the 1 kHz–10 MHz range, without any sign of Stimulated Brillouin Scattering (SBS). These results highlight the amplifier’s suitability for demanding industrial and scientific applications, including quantum computing, where narrowband emission, low Relative Intensity Noise (RIN), and reliability are critical.
- 22 July 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (15) , 32061-32071
Open Access50 W low-noise single-frequency thulium-doped fiber amplifier at 1844 nm
In this work, we present a 50 W laser amplifier architecture operating at 1844 nm, encompassing a three-stage amplification architecture. The first two stages rely on core-pumping, while the final stage employs high-power cladding pumping. Core-pumping at 1560 nm enables a tunable output power of 2 W between 1830 nm and 1880 nm at the output of the second preamplifier. An integrated spectral filter comprising a circulator and a fiber Bragg grating (FBG) centered at 844 nm is used. Cladding pumping at 793 nm is implemented for power scaling, achieving over 50 W of output power with an optical signal-to-noise ratio (OSNR) exceeding 60 dB. The amplifier exhibits low intensity noise, with an RMS noise of 0.006% in the 1 kHz–10 MHz range, without any sign of Stimulated Brillouin Scattering (SBS). These results highlight the amplifier’s suitability for demanding industrial and scientific applications, including quantum computing, where narrowband emission, low Relative Intensity Noise (RIN), and reliability are critical.
- Open Access
- 11 June 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (12) , 26139-26151
High-repetition rate ultrafast burst laser processing of copper and silicon up to 15 GHz
Ultrafast lasers are widely used in microfabrication due to their precision and minimal thermal damage, but their throughput is often limited. Processing with bursts of pulses with GHz repetition rates aims to enhance ablation efficiency. However, recent results have shown strong dependencies on the number of pulses within the burst. The present work focuses on the pulse repetition rate. We report ultrafast laser ablation in copper and silicon at unexplored intra-burst repetition rates, from 1 up to 15 GHz, in both single and multi-burst processing. High-resolution scanning electron microscopy is used to characterize ablation volumes and crater morphology. Our results demonstrate a benefit in the ablation efficiency at very high repetition rates in the case of copper. It also shows that optimal processing for silicon and copper is observed with very different parameter configurations. This difference is attributed to the different thermal diffusivities. In addition, the crater morphologies across the different studied configurations strongly suggest a dependency on the viscosity of the liquid phase, providing insight into the varying temperatures reached during ablation.
- 11 June 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (12) , 26139-26151
Open AccessHigh-repetition rate ultrafast burst laser processing of copper and silicon up to 15 GHz
Ultrafast lasers are widely used in microfabrication due to their precision and minimal thermal damage, but their throughput is often limited. Processing with bursts of pulses with GHz repetition rates aims to enhance ablation efficiency. However, recent results have shown strong dependencies on the number of pulses within the burst. The present work focuses on the pulse repetition rate. We report ultrafast laser ablation in copper and silicon at unexplored intra-burst repetition rates, from 1 up to 15 GHz, in both single and multi-burst processing. High-resolution scanning electron microscopy is used to characterize ablation volumes and crater morphology. Our results demonstrate a benefit in the ablation efficiency at very high repetition rates in the case of copper. It also shows that optimal processing for silicon and copper is observed with very different parameter configurations. This difference is attributed to the different thermal diffusivities. In addition, the crater morphologies across the different studied configurations strongly suggest a dependency on the viscosity of the liquid phase, providing insight into the varying temperatures reached during ablation.
- 19 February 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (5) , 1476-1479
Femtosecond pulses at 914 nm without mode-locking using Nd-doped fiber amplifiers
We present a fiber laser system that generates femtosecond pulses at 914 nm from a continuous-wave solid-state laser source and using Nd-doped fiber amplifiers. This femtosecond laser architecture without mode-locking is based on picosecond pulse shaping by an electro-optic modulator followed by a Mamyshev regenerator to shorten the pulses down to 8 ps. Additional spectral broadening by self-phase modulation results in an output pulse spectrum of 10 nm, allowing the generation of nearly transform-limited 230 fs pulses.
- 19 February 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (5) , 1476-1479
Femtosecond pulses at 914 nm without mode-locking using Nd-doped fiber amplifiers
We present a fiber laser system that generates femtosecond pulses at 914 nm from a continuous-wave solid-state laser source and using Nd-doped fiber amplifiers. This femtosecond laser architecture without mode-locking is based on picosecond pulse shaping by an electro-optic modulator followed by a Mamyshev regenerator to shorten the pulses down to 8 ps. Additional spectral broadening by self-phase modulation results in an output pulse spectrum of 10 nm, allowing the generation of nearly transform-limited 230 fs pulses.
- Open Access
- 18 October 2024
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 307, 02033
Tunable 30W all-fiber laser emitting around 1850 nm
We have demonstrated a tunable polarization maintaining thulium-doped fiber laser spanning the 1830nm-1880nm range with a fiber-coupled output power as high as 30W CW. The high- power booster stage is made using double clad fibers pumped with 793nm laser diodes.
- 18 October 2024
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 307, 02033
Open AccessTunable 30W all-fiber laser emitting around 1850 nm
We have demonstrated a tunable polarization maintaining thulium-doped fiber laser spanning the 1830nm-1880nm range with a fiber-coupled output power as high as 30W CW. The high- power booster stage is made using double clad fibers pumped with 793nm laser diodes.
- Open Access
- 6 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (1) , 1-6
Optimization of Nd-Doped LMA Fibers for High-Power Laser Emission Near 915 nm
We report on the development of low numerical aperture (NA) Nd-doped large mode area (LMA) fibers with optimized core/clad geometry to achieve high-power laser emission near 915 nm while maintaining near diffraction-limited output beam. The influence of clad-to-core ratio on the detrimental amplified spontaneous emission (ASE) at 1050 nm and on the beam quality was studied experimentally in different amplifier configurations. We also show that bending the Nd-doped LMA fiber to a precise radius of curvature significantly improves the overall laser performances of these fibers by limiting both higher-order modes and spurious ASE at 1050 nm. The possibility of all-fiber multi-stages amplifier configurations with diffraction-limited output beam is finally discussed.
- 6 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (1) , 1-6
Open AccessOptimization of Nd-Doped LMA Fibers for High-Power Laser Emission Near 915 nm
We report on the development of low numerical aperture (NA) Nd-doped large mode area (LMA) fibers with optimized core/clad geometry to achieve high-power laser emission near 915 nm while maintaining near diffraction-limited output beam. The influence of clad-to-core ratio on the detrimental amplified spontaneous emission (ASE) at 1050 nm and on the beam quality was studied experimentally in different amplifier configurations. We also show that bending the Nd-doped LMA fiber to a precise radius of curvature significantly improves the overall laser performances of these fibers by limiting both higher-order modes and spurious ASE at 1050 nm. The possibility of all-fiber multi-stages amplifier configurations with diffraction-limited output beam is finally discussed.
- 1 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (25) , 42495-42506
Neodymium laser-pumped ultra-low noise tunable Brillouin fiber laser around 920 nm
We have developed an ultra-low noise tunable Brillouin fiber laser exhibiting three orders of magnitude better frequency noise performance than the Neodymium-doped fiber laser pump and remarkable optical signal-to-noise ratio exceeding 80 dB suitable for immediate applications in coherent nonlinear conversion, quantum computing and underwater communications. In addition, we have implemented a custom optical phase-locked loop to ensure long-term stable operation and have investigated its impact on frequency noise. We demonstrate the power scalability of the single frequency (Hz-class) Brillouin laser, delivering over 500 mW with tunability across the 900 nm to 930 nm range in an all-fiber fully polarization-maintaining architecture.
- 1 December 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (25) , 42495-42506
Neodymium laser-pumped ultra-low noise tunable Brillouin fiber laser around 920 nm
We have developed an ultra-low noise tunable Brillouin fiber laser exhibiting three orders of magnitude better frequency noise performance than the Neodymium-doped fiber laser pump and remarkable optical signal-to-noise ratio exceeding 80 dB suitable for immediate applications in coherent nonlinear conversion, quantum computing and underwater communications. In addition, we have implemented a custom optical phase-locked loop to ensure long-term stable operation and have investigated its impact on frequency noise. We demonstrate the power scalability of the single frequency (Hz-class) Brillouin laser, delivering over 500 mW with tunability across the 900 nm to 930 nm range in an all-fiber fully polarization-maintaining architecture.
- Open Access
Effect of Linewidth on the Relative Intensity Noise in Random Distributed Feedback Raman Fiber Lasers
We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz.
Open AccessEffect of Linewidth on the Relative Intensity Noise in Random Distributed Feedback Raman Fiber Lasers
We experimentally explore the relation between spectral linewidth and RIN transfer in half-open cavity random distributed feedback Raman lasers, demonstrating for the first time the possibility of adjusting the pump-to-signal RIN transfer intensity and cut-off frequency by using spectral filtering in the reflector section. We apply this approach to a 50-km laser system, operating in the C-Band, reliant on a standard single-mode fiber. We obtained a minimum bandwidth of 13 pm, which translates into a visible RIN cut-off at 800 MHz.
- 13 October 2022
- Published by Optica Publishing Group in Optics Letters
- Vol. 47 (20) , 5405-5408
Multi-gigahertz femtosecond pulses from linear and nonlinear propagation of a phase-modulated laser
We propose and demonstrate a non-mode-locking approach to generating multi-gigahertz repetition rate, femtosecond pulses in burst mode by shaping a continuous-wave (CW) seed laser in an all-fiber configuration. The seed laser at 1030 nm is first phase modulated and de-chirped to low-contrast, ∼2 ps pulses at a 17.5 GHz repetition rate, then carved to bursts at a 60 kHz repetition rate, and finally shaped to <2 ps clean pulses by a Mamyshev regenerator. This prepared high-quality picosecond source is further used to seed an Yb-doped fiber amplifier operating in the highly nonlinear regime, delivering output pulses at 23 nJ/pulse and $20\,\mathrm{\mu}$J/burst, compressible to ∼100 fs level. The system eliminates the need for mode-locked cavities and simplifies conventional ultrafast electro-optic combs to using only one phase modulator, while providing femtosecond pulses at multiple gigahertz repetition rate, enhanced pulse energy in burst mode and the potential of further power/energy scaling.
- 13 October 2022
- Published by Optica Publishing Group in Optics Letters
- Vol. 47 (20) , 5405-5408
Multi-gigahertz femtosecond pulses from linear and nonlinear propagation of a phase-modulated laser
We propose and demonstrate a non-mode-locking approach to generating multi-gigahertz repetition rate, femtosecond pulses in burst mode by shaping a continuous-wave (CW) seed laser in an all-fiber configuration. The seed laser at 1030 nm is first phase modulated and de-chirped to low-contrast, ∼2 ps pulses at a 17.5 GHz repetition rate, then carved to bursts at a 60 kHz repetition rate, and finally shaped to <2 ps clean pulses by a Mamyshev regenerator. This prepared high-quality picosecond source is further used to seed an Yb-doped fiber amplifier operating in the highly nonlinear regime, delivering output pulses at 23 nJ/pulse and $20\,\mathrm{\mu}$J/burst, compressible to ∼100 fs level. The system eliminates the need for mode-locked cavities and simplifies conventional ultrafast electro-optic combs to using only one phase modulator, while providing femtosecond pulses at multiple gigahertz repetition rate, enhanced pulse energy in burst mode and the potential of further power/energy scaling.