CBChristian Berger

Christian Berger

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Christian Berger has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Various Binder Jet Printers on the Additive Manufacturing of Hardmetals

    by Christian Berger, Johannes Pötschke, Uwe Scheithauer, Alexander Michaelis

    Binder Jetting (BJT), a powder-based additive manufacturing technology, has been shown to be a fast and reproducible green shaping process for many different metals. Due to its high productivity and versatility in material processing, BJT is gaining increasing importance in the manufacturing sector. It can also be used for the production of WC-Co hardmetals, a primary ceramic-based composite often used for tools and wear parts. Five different BJT printers from four different manufacturers were evaluated to assess their effectiveness and feasibility in producing hardmetals based on the same WC-12 wt.% Co starting powders. The analysis focused on comparing the properties of the resulting hardmetals, as well as evaluating the printing performance. The results show that all tested BJT printers are fundamentally well suited for producing green hardmetal parts, which can achieve full density after sintering. This work highlights the potential of BJT technology in hardmetal manufacturing for tool production.


  • Open Access

    Printing Direction Effects on the Sliding Contact Response of a Binder Jetting 3D-Printed WC-Co Hardmetal

    by Laura Cabezas, Christian Berger, Emilio Jiménez-Piqué, Johannes Pötschke, Luis Llanes

    Binder jetting additive manufacturing offers a promising route to produce complex geometries in cemented carbides (WC-Co), but it may introduce direction-dependent microstructural variations potentially affecting wear resistance. This study investigates the influence of printing direction on the sliding contact response of 3D-printed and subsequently sintered (BJT) WC-12%Co. Prismatic specimens were printed along two orientations and subjected to single and repetitive scratch tests on three orthogonal faces. The microstructure, Vickers and scratch hardness, and wear rate were analyzed. The results showed a heterogeneous microstructure consisting of a matrix of fine carbides where several large particles where embedded. It was different from the homogenous microstructural scenarios exhibited by conventionally pressed and sintered fine- and coarse-grained hardmetals, used as reference for comparison purposes. The influence of printing direction on either the microstructure or mechanical properties of BJT specimens was found to be negligible. Interestingly, BJT samples exhibited superior wear resistance than the reference hardmetals, even though the hardness levels were alike for all the studied hardmetal grades. Such behavior is attributed to the co-existence of coarse and fine carbides within the microstructure, combining the energy absorption capability of the former with the inherent strength of the latter. These findings, together with the intrinsic flexibility and versatility advantages associated with additive manufacturing, highlight the potential of BJT hardmetals to be used in applications where contact load bearing or wear resistance are critical design parameters. Finally, the effectiveness of implementing an iterative sliding contact test for evaluating wear behavior in cemented carbides was also validated.


  • Open Access

    Correlation of Different Cemented Carbide Starting Powders with the Resulting Properties of Components Manufactured via Binder Jetting

    by Christian Berger, Johannes Pötschke, Uwe Scheithauer, Alexander Michaelis

    For several years, researchers have been exploring the use of the binder jetting powder-based additive manufacturing process to produce WC-Co hardmetals. Compared to other additive manufacturing processes, binder jetting has the potential for high-volume production. However, due to the powder-based approach, the resulting green bodies typically have low green density, limiting the achievable hardness and requiring higher Co content. Choosing the appropriate starting powder and post-processing can extend previous limitations and allow the selection of a suitable powder based on the application. This investigation focuses on exploring and evaluating the correlation between varying morphologies of WC-Co starting powders, their processability using the BJT method, and the resultant mechanical properties of sintered components.


  • Binder-jetting of TiCN-based cermets

    by Christian Berger, Johannes Pötschke, Manfred Fries, Tassilo Moritz, Alexander Michaelis

    Additive Manufacturing is experiencing an upswing in many sectors of industry for a broad variety of materials. Processes are mainly developed for polymers and metals. For ceramics, hardmetals and especially cermets there are only a few additive processes suitable. The powder-based technique Binder-Jetting is one of these suitable processes with high productivity and relatively low green density. Within this study, TiCN-based cermets are printed by Binder-Jetting for the first time. The complexity of influences of the morphology and composition of cermet powders are discussed in regard to bulk density and material properties of printed and sintered parts. Studied TiCN-based cermet compositions represent different Ni and Mo2C contents. Main points of this investigation are further the adjustment of ratio of the raw materials for good sintering behaviour and their influence on the microstructures and as a function of varied sintering temperatures.


  • Manufacturing and Properties of Tungsten Carbide-Oxide Composites

    by Anne Vornberger, Johannes Pötschke, Christian Berger

    Conventional WC-Co hardmetals are widely used in various applications due to their excellent properties. High hardness can be achieved using compositions with little to no content of cobalt or nickel. These binder metals are hazardous to health, making a substitution not only desirable because of availability and cost reasons. A new possibility to manufacture such hard materials is the combination of tungsten carbide with oxides such as Al2O3 and ZrO2. In this way the binder metal content can be replaced. Furthermore the content of the also expensive WC can be reduced. Such metal carbide – oxide composites with oxide contents between 16 vol% and 40 vol% were manufactured. The completely dense composites feature high hardness values of 2000 HV10 to 2400 HV10 while also having an acceptable fracture toughness of up to 7 MPa⋅m1/2. The improved mechanical properties make the replacement of WC-Co hardmetals and binder free WC ceramics in special areas possible.