Marina V. Korchagina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marina V. Korchagina has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Kireev
Don State Technical University
20 shared publications - Alexey Lebedev
Don State Technical University
9 shared publications - Andrey Efimov
Don State Technical University
5 shared publications - Andrey V. Efimov
Don State Technical University, 344000 Rostov-on-Don, Russia
3 shared publications - Valentin Stepanov
Don State Technical University
3 shared publications - Kh. K. Kaderov
Don State Technical University
2 shared publications
Latest Publications
- 8 June 2025
- Published by Springer Nature
- p. 649-663
Optimization of the Demulsifier Elements Design
- 8 June 2025
- Published by Springer Nature
- p. 665-678
Replacement of the Pinion Shaft by a Split Shaft-Hub Connection with Justification for the Choice of Connection Type
- 8 June 2025
- Published by Springer Nature
- p. 665-678
Replacement of the Pinion Shaft by a Split Shaft-Hub Connection with Justification for the Choice of Connection Type
- Open Access
- 25 December 2024
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 24 (4) , 316-327
Investigation of Parameters Influencing the Establishment of Hydrostatic Mode in the Crosshead-Guide Assembly of High-Pressure Plunger Pump
Introduction. When applying hydraulic fracturing technology to increase the efficiency of formation fluids, high-pressure pumps with a crosshead drive assembly are used. The major problem in the operation of these pumps is the wear of the crosshead guides. The crosshead is a flat sliding friction pair, leading to wear of the plunger seals and a decrease in the basic pump performance indicators. To solve this problem, it was previously proposed to use new materials and antifriction coatings, original designs of friction units, etc. However, a detailed description and solution to the problem under consideration has not been found in the literature at present. The objective of this study is to determine, under maximum load, the influence of the unit design, process temperature and pressure in the lubrication system on the values of the parameters that provide for the hydrostatic mode for a flat thrust bearing in a crosshead-guide unit of a high-pressure plunger pump.Materials and Methods. The parameters were determined by the simulation technique using modal analysis applicable in the case of high dynamic loads acting on the studied unit. The calculation of the hydrodynamic parameters of the lubricating layer was based on the combination of the Reynolds model and the Stokes model in numerical modeling. The study was conducted using a calculation model representing a section of a plunger pump, considered as “flexible bodies” model, in the field of gravity forces. The mathematical dependences of the parameters under consideration were presented in the form of regression equations obtained from the results of a numerical experiment.Results. The maximum load on the lower crosshead guide was determined, for which further hydrodynamic studies were conducted. Factors influencing the process were studied — gaps filled with lubricant (depending on the design of the unit), temperature, and pressure in the lubrication system. Mathematical dependences of the influence of the considered factors on the values of the parameters determining the establishment of the hydrostatic mode were obtained.Discussion and Conclusion. The obtained mathematical models show the degree and influence of the factors under consideration on the studied parameters of the hydrostatic lubrication mode of the unit — the force acting on the crosshead from the lubricating layer, and the mass flow rate of the lubricant at the outlet of the system. It is found that the greatest influence is exerted by the change in the volume of gaps filled with lubricant, the mass flow rate of lubricant at the entrance to the system, which simulates the increase in pressure in the lubrication system of the friction unit. The results obtained do not contradict the conclusions reached in works on similar topics, and can be used in further research.
- 25 December 2024
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 24 (4) , 316-327
Open AccessInvestigation of Parameters Influencing the Establishment of Hydrostatic Mode in the Crosshead-Guide Assembly of High-Pressure Plunger Pump
Introduction. When applying hydraulic fracturing technology to increase the efficiency of formation fluids, high-pressure pumps with a crosshead drive assembly are used. The major problem in the operation of these pumps is the wear of the crosshead guides. The crosshead is a flat sliding friction pair, leading to wear of the plunger seals and a decrease in the basic pump performance indicators. To solve this problem, it was previously proposed to use new materials and antifriction coatings, original designs of friction units, etc. However, a detailed description and solution to the problem under consideration has not been found in the literature at present. The objective of this study is to determine, under maximum load, the influence of the unit design, process temperature and pressure in the lubrication system on the values of the parameters that provide for the hydrostatic mode for a flat thrust bearing in a crosshead-guide unit of a high-pressure plunger pump.Materials and Methods. The parameters were determined by the simulation technique using modal analysis applicable in the case of high dynamic loads acting on the studied unit. The calculation of the hydrodynamic parameters of the lubricating layer was based on the combination of the Reynolds model and the Stokes model in numerical modeling. The study was conducted using a calculation model representing a section of a plunger pump, considered as “flexible bodies” model, in the field of gravity forces. The mathematical dependences of the parameters under consideration were presented in the form of regression equations obtained from the results of a numerical experiment.Results. The maximum load on the lower crosshead guide was determined, for which further hydrodynamic studies were conducted. Factors influencing the process were studied — gaps filled with lubricant (depending on the design of the unit), temperature, and pressure in the lubrication system. Mathematical dependences of the influence of the considered factors on the values of the parameters determining the establishment of the hydrostatic mode were obtained.Discussion and Conclusion. The obtained mathematical models show the degree and influence of the factors under consideration on the studied parameters of the hydrostatic lubrication mode of the unit — the force acting on the crosshead from the lubricating layer, and the mass flow rate of the lubricant at the outlet of the system. It is found that the greatest influence is exerted by the change in the volume of gaps filled with lubricant, the mass flow rate of lubricant at the entrance to the system, which simulates the increase in pressure in the lubrication system of the friction unit. The results obtained do not contradict the conclusions reached in works on similar topics, and can be used in further research.
- 2 February 2024
- Published by Springer Nature
- p. 596-605
Optimization of Parameters of a Hydraulic Mobile Pumping Unit for Hydraulic Fracturing
- 2 February 2024
- Published by Springer Nature
- p. 596-605
Optimization of Parameters of a Hydraulic Mobile Pumping Unit for Hydraulic Fracturing
- 2 February 2024
- Published by Springer Nature
- p. 606-615
Designing a Mobile High-Pressure Well Service Pump Unit on a Vehicle Chassis
- 2 February 2024
- Published by Springer Nature
- p. 606-615
Designing a Mobile High-Pressure Well Service Pump Unit on a Vehicle Chassis
- Open Access
- 29 September 2023
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 23 (3) , 269-282
Optimization of Geometric Characteristics of Cycloidal Profiles of Gerotor Hydraulic Machines
Introduction. The performance and reliability of gerotor hydraulic machines depend on the geometry of the cycloidal gearing profile. The existing methods of calculating and optimizing the profile parameters are cumbersome, multicriteria and difficult for practical application. Therefore, the problem of creating the methodology for calculating the parameters of the gerotor machine profile suitable for engineering calculations at the stage of conceptual design is a challenge. In this regard, the objective of this work was to modernize the methodology for designing the geometry of the profiles of the end section of hypocycloidal gears used in gerotor hydraulic machines, and to analyze the possibilities of their optimization during preliminary design. In the course of the study, the Mathcad computer mathematics system was used; numerical experiments were carried out to study the influence of geometric profile parameters on the performance and operability of the gerotor hydraulic machine, based on the data obtained and analyzed; recommendations for the design of optimal profiles of the end section of gerotor hydraulic machines were developed.Materials and Methods. Materials included known methods of profile parameters calculation, based on application of classical formulas of hypocycloidal equidistant used for outlining profiles of teeth of working elements of gerotor machines. The basic research method was modeling the gerotor machine profile using Mathcad computer mathematics system. Calculated data were obtained for the selected ranges of varying parameters, processed through the univariate regression analysis.Results. An algorithm for analyzing the tooth profile smoothness was developed. Two target parameters were defined: the cross-sectional area of the end profile, which affects the productivity; the smallest reduced radius of contact that determines operability of the working body. A technique for calculating the target parameters at the early stage of design was proposed. A number of optimal values of profile parameters according to the criteria of productivity and operability of gerotor machine was obtained. The dependences providing the optimum values of profile parameters at the stage of designing were constructed.Discussion and Conclusion. The developed methodology makes it possible to obtain an assessment of the performance and operability of the gerotor hydraulic machine at the design stage of the working body. The research results can be used in mechanical engineering when designing gerotor hydraulic machines in order to improve their technical and operational characteristics.
- 29 September 2023
- Published by FSFEI HE Don State Technical University in Advanced Engineering Research (Rostov-on-Don)
- Vol. 23 (3) , 269-282
Open AccessOptimization of Geometric Characteristics of Cycloidal Profiles of Gerotor Hydraulic Machines
Introduction. The performance and reliability of gerotor hydraulic machines depend on the geometry of the cycloidal gearing profile. The existing methods of calculating and optimizing the profile parameters are cumbersome, multicriteria and difficult for practical application. Therefore, the problem of creating the methodology for calculating the parameters of the gerotor machine profile suitable for engineering calculations at the stage of conceptual design is a challenge. In this regard, the objective of this work was to modernize the methodology for designing the geometry of the profiles of the end section of hypocycloidal gears used in gerotor hydraulic machines, and to analyze the possibilities of their optimization during preliminary design. In the course of the study, the Mathcad computer mathematics system was used; numerical experiments were carried out to study the influence of geometric profile parameters on the performance and operability of the gerotor hydraulic machine, based on the data obtained and analyzed; recommendations for the design of optimal profiles of the end section of gerotor hydraulic machines were developed.Materials and Methods. Materials included known methods of profile parameters calculation, based on application of classical formulas of hypocycloidal equidistant used for outlining profiles of teeth of working elements of gerotor machines. The basic research method was modeling the gerotor machine profile using Mathcad computer mathematics system. Calculated data were obtained for the selected ranges of varying parameters, processed through the univariate regression analysis.Results. An algorithm for analyzing the tooth profile smoothness was developed. Two target parameters were defined: the cross-sectional area of the end profile, which affects the productivity; the smallest reduced radius of contact that determines operability of the working body. A technique for calculating the target parameters at the early stage of design was proposed. A number of optimal values of profile parameters according to the criteria of productivity and operability of gerotor machine was obtained. The dependences providing the optimum values of profile parameters at the stage of designing were constructed.Discussion and Conclusion. The developed methodology makes it possible to obtain an assessment of the performance and operability of the gerotor hydraulic machine at the design stage of the working body. The research results can be used in mechanical engineering when designing gerotor hydraulic machines in order to improve their technical and operational characteristics.
- 29 January 2023
- Published by Springer Nature
- p. 547-553
Research of Tension and Deformations in the Elastic Element of the Universal Spherical Preventer Seal
- 29 January 2023
- Published by Springer Nature
- p. 547-553
Research of Tension and Deformations in the Elastic Element of the Universal Spherical Preventer Seal
- 16 November 2022
- Published by Springer Nature
- p. 1541-1550
Model of Hole Mandrel Process in Tubular Workpieces
- 16 November 2022
- Published by Springer Nature
- p. 1541-1550
Model of Hole Mandrel Process in Tubular Workpieces
- 16 November 2022
- Published by Springer Nature
- p. 1727-1736
Optimization of Structure Parameters of Semi-trailer-tank for Hydraulic Fracturing of Formation
- 16 November 2022
- Published by Springer Nature
- p. 1727-1736
Optimization of Structure Parameters of Semi-trailer-tank for Hydraulic Fracturing of Formation
- 5 October 2021
- Published by Springer Nature
- p. 93-105
Optimization of Hopper System of Pump Unit on Automotive Chassis
- 5 October 2021
- Published by Springer Nature
- p. 93-105
Optimization of Hopper System of Pump Unit on Automotive Chassis