Kazuhiro Honda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Kazuhiro Honda has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Kun Li
Advanced Wireless and Communication Research Center (AWCC), The University of Electro-Communications, Tokyo, Japan
5 shared publications - Koichi Ogawa
Hosei University
4 shared publications - Xiaolong Wang
Jilin University
2 shared publications - Akitada Ichinose
Department of Molecular Patho-Biochemistry and Patho-Biology, Yamagata University School of Medicine, Yamagata, Japan
1 shared publication Daishi Iwamoto
Graduate School of Engineering, Toyama University
1 shared publicationGeyu Lu
State Key Laboratory of Integrated Optoelectronics, College of Electronic Science and Engineering, International Center of Future Science, Jilin University, Changchun, China
1 shared publication
Latest Publications
- Open Access
Measurement and Analysis of the Rician K-Factor for Low-Altitude UAV Air-to-Ground Communications at 2.5 GHz
The research and development of unmanned aerial vehicles (UAVs) is progressing rapidly, and they are expected to be used in a wide range of applications. In this paper, we evaluated the propagation characteristics of air-to-ground (A2G) communications used by UAVs. Specifically, we investigated the Rician K-factor, which is one of the indicators representing the impact on communication quality. We carried out radio wave propagation measurements for A2G communications at low altitudes in propagation environments with simple (S environment) and complex (C environment) structures within the measurement area and then performed a detailed evaluation of the effect of the distance from buildings, UAV altitude, and antenna installation on the Rician K-factor and propagation characteristics. The measurement and analytical results reveal that the Rician K-factor in an S environment was observed to be high due to the strong dominance of the direct wave. On the other hand, the Rician K-factor in a C environment decreased because of complex multiple reflected and diffracted waves caused by surrounding buildings. In addition, dummy fading signals generated from the useful path calculated with the ray-tracing method using a simple 3D analytical model showed a high degree of agreement with the experimental results. These outcomes provide key parameters for the optimal design of UAV-based A2G communication systems, contributing to the practical application of UAV operations.
Open AccessMeasurement and Analysis of the Rician K-Factor for Low-Altitude UAV Air-to-Ground Communications at 2.5 GHz
The research and development of unmanned aerial vehicles (UAVs) is progressing rapidly, and they are expected to be used in a wide range of applications. In this paper, we evaluated the propagation characteristics of air-to-ground (A2G) communications used by UAVs. Specifically, we investigated the Rician K-factor, which is one of the indicators representing the impact on communication quality. We carried out radio wave propagation measurements for A2G communications at low altitudes in propagation environments with simple (S environment) and complex (C environment) structures within the measurement area and then performed a detailed evaluation of the effect of the distance from buildings, UAV altitude, and antenna installation on the Rician K-factor and propagation characteristics. The measurement and analytical results reveal that the Rician K-factor in an S environment was observed to be high due to the strong dominance of the direct wave. On the other hand, the Rician K-factor in a C environment decreased because of complex multiple reflected and diffracted waves caused by surrounding buildings. In addition, dummy fading signals generated from the useful path calculated with the ray-tracing method using a simple 3D analytical model showed a high degree of agreement with the experimental results. These outcomes provide key parameters for the optimal design of UAV-based A2G communication systems, contributing to the practical application of UAV operations.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (11) , 15807-15817
Beyond 20 Bits/s/Hz Channel Capacity Realization With Compact MIMO Antennas for Human-Centric IoT Devices
This paper presents a highly compact multiple-input multiple-output (MIMO) antenna system that maintains a high and stable channel capacity above 20 bits/s/Hz in dynamic channels for human-centric Internet of Things (IoT) devices. The MIMO array consists of four compact antenna elements and four compact control circuits operating at 2.45 GHz. This antenna system achieves a 64.5% reduction in dimension compared to the traditional microstrip patch. Each antenna is connected to a compact control circuit, boasting a wide power-tunable range exceeding 30.3 dB and a phase difference within 90∘ ± 15∘. The transmission coefficient between every two elements of the MIMO array is designed to be less than −20.9 dB. The well-integrated structure of the antenna and coupler realizes a wide range weight function that mitigates the polarization mismatch caused by the variations in the cross-polarization power ratio (XPR) of incoming waves and the antenna’s inclination angle during human arm-swing motion in human-centric IoT use scenarios. The radiation performance concerning polarization control was examined in an anechoic chamber. Furthermore, a 4×4 MIMO channel capacity experiment was conducted using a three-dimensional spatial fading emulator with an arm-swinging human phantom. A reasonable agreement between the measured and simulated results indicates that the proposed antenna system can achieve a high and stable MIMO channel capacity of over 20 bits/s/Hz irrespective of the XPR and inclination angles.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 12 (11) , 15807-15817
Beyond 20 Bits/s/Hz Channel Capacity Realization With Compact MIMO Antennas for Human-Centric IoT Devices
This paper presents a highly compact multiple-input multiple-output (MIMO) antenna system that maintains a high and stable channel capacity above 20 bits/s/Hz in dynamic channels for human-centric Internet of Things (IoT) devices. The MIMO array consists of four compact antenna elements and four compact control circuits operating at 2.45 GHz. This antenna system achieves a 64.5% reduction in dimension compared to the traditional microstrip patch. Each antenna is connected to a compact control circuit, boasting a wide power-tunable range exceeding 30.3 dB and a phase difference within 90∘ ± 15∘. The transmission coefficient between every two elements of the MIMO array is designed to be less than −20.9 dB. The well-integrated structure of the antenna and coupler realizes a wide range weight function that mitigates the polarization mismatch caused by the variations in the cross-polarization power ratio (XPR) of incoming waves and the antenna’s inclination angle during human arm-swing motion in human-centric IoT use scenarios. The radiation performance concerning polarization control was examined in an anechoic chamber. Furthermore, a 4×4 MIMO channel capacity experiment was conducted using a three-dimensional spatial fading emulator with an arm-swinging human phantom. A reasonable agreement between the measured and simulated results indicates that the proposed antenna system can achieve a high and stable MIMO channel capacity of over 20 bits/s/Hz irrespective of the XPR and inclination angles.
- Open Access
Smart Gateway for Healthcare Networks Based on Beam Steering Technology
To ensure high-reliability communication in healthcare networks, this paper presents a smart gateway system that includes an angle-of-arrival (AOA) estimation and a beam steering function for a small circular antenna array. To form a beam toward healthcare sensors, the proposed antenna estimates the direction of the sensors utilizing the radio-frequency-based interferometric monopulse technique. The fabricated antenna was assessed based on the measurements of complex directivity and the over-the-air (OTA) testing in Rice propagation environments using a two-dimensional fading emulator. The measurement results reveal that the accuracy of the AOA estimation agrees well with that of the analytical data obtained through the Monte Carlo simulation. This antenna is embedded with a beam steering function employing phased array technology, which can form a beam spaced at 45° intervals. The ability of full-azimuth beam steering with regard to the proposed antenna was evaluated by beam propagation experiments using a human phantom in an indoor environment. The received signal of the proposed antenna with beam steering increases more than that of a conventional dipole antenna, confirming that the developed antenna has great potential of achieving high-reliability communication in a healthcare network.
Open AccessSmart Gateway for Healthcare Networks Based on Beam Steering Technology
To ensure high-reliability communication in healthcare networks, this paper presents a smart gateway system that includes an angle-of-arrival (AOA) estimation and a beam steering function for a small circular antenna array. To form a beam toward healthcare sensors, the proposed antenna estimates the direction of the sensors utilizing the radio-frequency-based interferometric monopulse technique. The fabricated antenna was assessed based on the measurements of complex directivity and the over-the-air (OTA) testing in Rice propagation environments using a two-dimensional fading emulator. The measurement results reveal that the accuracy of the AOA estimation agrees well with that of the analytical data obtained through the Monte Carlo simulation. This antenna is embedded with a beam steering function employing phased array technology, which can form a beam spaced at 45° intervals. The ability of full-azimuth beam steering with regard to the proposed antenna was evaluated by beam propagation experiments using a human phantom in an indoor environment. The received signal of the proposed antenna with beam steering increases more than that of a conventional dipole antenna, confirming that the developed antenna has great potential of achieving high-reliability communication in a healthcare network.
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (7) , 1333-1337
Two-Way Power Divider With Wide Tunable Power Ratio Range for Weighted-Polarization MIMO Antenna in BAN Radios at 2.45 GHz
This study presented an implementation of weighted-polarization multiple-input multiple-output (MIMO) antenna for wireless body area networks (BANs) at 2.45 GHz. The weight function determined by considering the variation in the cross-polarization power ratio (XPR) and the antenna tilt angle was realized by a 2-way power divider (PD), where tunable power ratio range of proposed PD could not only cross the boundary of equal power ratio (k2 = 1), but also maintain a wide tunable range at the same time. The patch array antenna fed by the proposed PD consists of microstrip lines, capacitors, resistors and varactor diodes can overcome the polarization mismatch in dynamic off-body channel due to the variation in radio-propagation environment and human movement by adjusting the bias voltages. The experiment of 22 MIMO channel capacity was conducted using a three-dimensional spatial fading emulator. The measured and simulated results are in good agreement. Under the considered condition of arm-swinging angle and the XPR, the tunable power ratio range of proposed PD can be realized from 1.25 dB to 20 dB, therefore, it is suitable for radio-frequency (RF) control antenna to obtaining high data transmission in future wearable MIMO applications.
- 13 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 21 (7) , 1333-1337
Two-Way Power Divider With Wide Tunable Power Ratio Range for Weighted-Polarization MIMO Antenna in BAN Radios at 2.45 GHz
This study presented an implementation of weighted-polarization multiple-input multiple-output (MIMO) antenna for wireless body area networks (BANs) at 2.45 GHz. The weight function determined by considering the variation in the cross-polarization power ratio (XPR) and the antenna tilt angle was realized by a 2-way power divider (PD), where tunable power ratio range of proposed PD could not only cross the boundary of equal power ratio (k2 = 1), but also maintain a wide tunable range at the same time. The patch array antenna fed by the proposed PD consists of microstrip lines, capacitors, resistors and varactor diodes can overcome the polarization mismatch in dynamic off-body channel due to the variation in radio-propagation environment and human movement by adjusting the bias voltages. The experiment of 22 MIMO channel capacity was conducted using a three-dimensional spatial fading emulator. The measured and simulated results are in good agreement. Under the considered condition of arm-swinging angle and the XPR, the tunable power ratio range of proposed PD can be realized from 1.25 dB to 20 dB, therefore, it is suitable for radio-frequency (RF) control antenna to obtaining high data transmission in future wearable MIMO applications.
- Open Access
Over-the-Air Testing of a Massive MIMO Antenna with a Full-Rank Channel Matrix
This paper presents an over-the-air testing method in which a full-rank channel matrix is created for a massive multiple-input multiple-output (MIMO) antenna system utilizing a fading emulator with a small number of scatterers. In the proposed method, in order to mimic a fading emulator with a large number of scatterers, the scatterers are virtually positioned by rotating the massive MIMO antenna. The performance of a 64-element quasi-half-wavelength dipole circular array antenna was evaluated using a two-dimensional fading emulator. The experimental results reveal that a large number of available eigenvalues are obtained from the channel response matrix, confirming that the proposed method, which utilizes a full-rank channel matrix, can be used to assess a massive MIMO antenna system.
Open AccessOver-the-Air Testing of a Massive MIMO Antenna with a Full-Rank Channel Matrix
This paper presents an over-the-air testing method in which a full-rank channel matrix is created for a massive multiple-input multiple-output (MIMO) antenna system utilizing a fading emulator with a small number of scatterers. In the proposed method, in order to mimic a fading emulator with a large number of scatterers, the scatterers are virtually positioned by rotating the massive MIMO antenna. The performance of a 64-element quasi-half-wavelength dipole circular array antenna was evaluated using a two-dimensional fading emulator. The experimental results reveal that a large number of available eigenvalues are obtained from the channel response matrix, confirming that the proposed method, which utilizes a full-rank channel matrix, can be used to assess a massive MIMO antenna system.
- 19 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Analysis of an Interferometric AOA Antenna with Ground Plane in a Rician Fading Channel
In this paper, we conduct investigations on interferometric angle-of-arrival (AOA) estimation using an AOA antenna mounted on a ground plane in a Rice propagation environment. The results reveal that the proposed antenna can provide AOA estimate with high accuracy even in a Rice fading channel.
- 19 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Analysis of an Interferometric AOA Antenna with Ground Plane in a Rician Fading Channel
In this paper, we conduct investigations on interferometric angle-of-arrival (AOA) estimation using an AOA antenna mounted on a ground plane in a Rice propagation environment. The results reveal that the proposed antenna can provide AOA estimate with high accuracy even in a Rice fading channel.
- Open Access
A Method of Implementing a 4 × 4 Correlation Matrix for Evaluating the Uplink Channel Properties of MIMO Over-the-Air Apparatus
This paper presents a method of implementing a 4 × 4 correlation matrix for evaluating the uplink channel properties of multiple-input multiple-output (MIMO) antennas using an over-the-air measurement system. First, the implementation model used to determine the correlation coefficients between the signals received at the base station (BS) antennas via the uplink channel is described. Then, a methodology is introduced to achieve a 4 × 4 correlation matrix for a BS MIMO antenna based on Jakes’ model by setting the initial phases of the secondary wave sources in the two-dimensional channel model. The performance of the uplink channel for a four-element MIMO terminal array antenna is evaluated using a two-dimensional bidirectional fading emulator. The results show that the measured correlation coefficients between the signals received via the uplink channel at the BS antennas using the proposed method are in good agreement with the BS correlation characteristics calculated using Monte Carlo simulation and the theoretical formula, thereby confirming the effectiveness of the proposed method.
Open AccessA Method of Implementing a 4 × 4 Correlation Matrix for Evaluating the Uplink Channel Properties of MIMO Over-the-Air Apparatus
This paper presents a method of implementing a 4 × 4 correlation matrix for evaluating the uplink channel properties of multiple-input multiple-output (MIMO) antennas using an over-the-air measurement system. First, the implementation model used to determine the correlation coefficients between the signals received at the base station (BS) antennas via the uplink channel is described. Then, a methodology is introduced to achieve a 4 × 4 correlation matrix for a BS MIMO antenna based on Jakes’ model by setting the initial phases of the secondary wave sources in the two-dimensional channel model. The performance of the uplink channel for a four-element MIMO terminal array antenna is evaluated using a two-dimensional bidirectional fading emulator. The results show that the measured correlation coefficients between the signals received via the uplink channel at the BS antennas using the proposed method are in good agreement with the BS correlation characteristics calculated using Monte Carlo simulation and the theoretical formula, thereby confirming the effectiveness of the proposed method.
- 25 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 507-508
A Miniaturized Large-Scale MIMO Antenna Using the Double-Ring Structure
This paper presents a miniaturized large-scale MIMO antenna for mobile stations. The use of double-ring structure comprising the inner and outer 64 × 64 MIMO arrays provides a compact 128 × 128 MIMO array due to an efficient array arrangement under the two-dimensional spatial constraint condition. A simple EM model comprising three elements is proposed, and a theoretical investigation is performed to determine the optimum radius of the inner array.
- 25 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 507-508
A Miniaturized Large-Scale MIMO Antenna Using the Double-Ring Structure
This paper presents a miniaturized large-scale MIMO antenna for mobile stations. The use of double-ring structure comprising the inner and outer 64 × 64 MIMO arrays provides a compact 128 × 128 MIMO array due to an efficient array arrangement under the two-dimensional spatial constraint condition. A simple EM model comprising three elements is proposed, and a theoretical investigation is performed to determine the optimum radius of the inner array.
- Open Access
- 19 September 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (9) , 871
Full-Azimuth Beam Steering MIMO Antenna Arranged in a Daisy Chain Array Structure
This paper presents a multiple-input, multiple-output (MIMO) antenna system with the ability to perform full-azimuth beam steering, and with the aim of realizing greater than 20 Gbps vehicular communications. The MIMO antenna described in this paper comprises 64 elements arranged in a daisy chain array structure, where 32 subarrays are formed by pairing elements in each subarray; the antenna yields 32 independent subchannels for MIMO transmission, and covers all communication targets regardless of their position relative to the array. Analytical results reveal that the proposed antenna system can provide a channel capacity of more than 200 bits/s/Hz at a signal-to-noise power ratio (SNR) of 30 dB over the whole azimuth, which is equivalent to 20 Gbps for a bandwidth of 100 MHz. This remarkably high channel capacity is shown to be due to two significant factors; the improved directivity created by the optimum in-phase excitation and the low correlation between the subarrays due to the orthogonal alignment of the array with respect to the incident waves. Over-the-air (OTA) experiments confirm the increase in channel capacity; the proposed antenna can maintain a constant transmission rate over all azimuth angles.
- 19 September 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (9) , 871
Open AccessFull-Azimuth Beam Steering MIMO Antenna Arranged in a Daisy Chain Array Structure
This paper presents a multiple-input, multiple-output (MIMO) antenna system with the ability to perform full-azimuth beam steering, and with the aim of realizing greater than 20 Gbps vehicular communications. The MIMO antenna described in this paper comprises 64 elements arranged in a daisy chain array structure, where 32 subarrays are formed by pairing elements in each subarray; the antenna yields 32 independent subchannels for MIMO transmission, and covers all communication targets regardless of their position relative to the array. Analytical results reveal that the proposed antenna system can provide a channel capacity of more than 200 bits/s/Hz at a signal-to-noise power ratio (SNR) of 30 dB over the whole azimuth, which is equivalent to 20 Gbps for a bandwidth of 100 MHz. This remarkably high channel capacity is shown to be due to two significant factors; the improved directivity created by the optimum in-phase excitation and the low correlation between the subarrays due to the orthogonal alignment of the array with respect to the incident waves. Over-the-air (OTA) experiments confirm the increase in channel capacity; the proposed antenna can maintain a constant transmission rate over all azimuth angles.
- Open Access
- 1 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEICE Communications Express
- Vol. 8 (4) , 104-109
Interferometric angle-of-arrival estimation using a simple weight network
This paper presents a method to estimate the Angle of Arrival (AOA) for incident waves, using an RF-based interferometric monopulse technique. We used an AOA network to yield a weight function for the received signals, in which the phase of the received signals for each element is delayed in accordance with the coordinate of the elements using the differing lengths of microstrip transmission lines. Based on electromagnetic field analysis and experimental results, it is clarified that the proposed method achieves a high degree of accuracy for AOA estimation.
- 1 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEICE Communications Express
- Vol. 8 (4) , 104-109
Open AccessInterferometric angle-of-arrival estimation using a simple weight network
This paper presents a method to estimate the Angle of Arrival (AOA) for incident waves, using an RF-based interferometric monopulse technique. We used an AOA network to yield a weight function for the received signals, in which the phase of the received signals for each element is delayed in accordance with the coordinate of the elements using the differing lengths of microstrip transmission lines. Based on electromagnetic field analysis and experimental results, it is clarified that the proposed method achieves a high degree of accuracy for AOA estimation.