Guangbin Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guangbin Yang has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Laigui Yu
National & Local Joint Engineering Research Center for Applied Technology of Hybrid Nanomaterials, Henan University, Kaifeng, China
13 shared publications- Pingyu Zhang
National & Local Joint Engineering Research Center for Applied Technology of Hybrid Nanomaterials, Henan University, Kaifeng, China
13 shared publications Shengmao Zhang
Institute of Nanoscience and Engineering, Henan University Kaifeng Henan China
13 shared publicationsYujuan Zhang
12 shared publicationsPingyu Zhang
7 shared publicationsChuanping Gao
3 shared publications
Latest Publications
- Open Access
- 10 October 2026
- Published by Tsinghua University Press in Friction
Efficient one-pot synthesis of molybdenum dialkyl dithiocarbamate and investigation on evolution mechanism of tribofilms in ester-based lubricants
Base oil polarity critically governs additive solubility, interfacial adsorption, and tribochemical reactions, which collectively determine friction, wear, and component service life. In this study, molybdenum dialkyldithiocarbamate (MoDTC) was synthesized via a facile one-pot route. Its dispersion stability and tribological properties were compared in two base oils with distinct polarities: polar diisooctyl sebacate (DIOS) and nonpolar polyalphaolefin (PAO6). The tribological behavior of the MoDTC/DIOS blend was further evaluated under variable applied loads and temperatures. The results reveal that MoDTC delivers superior friction-reducing and anti-wear performance in nonpolar PAO6, attributed to stable adsorption on friction surfaces and tribochemical decomposition into protective tribofilms. In contrast, polar DIOS enables the MoDTC/DIOS blend to reach a steady friction coefficient (COF) much faster, with a drastically shortened running-in stage. Cross-sectional characterizations demonstrate that the polar DIOS environment accelerates MoDTC decomposition and rapid formation of an amorphous Mo- and S-containing tribofilm, accounting for the sharp COF decline. Nevertheless, this amorphous tribofilm exhibits low load-bearing capacity and cannot effectively suppress interfacial wear, resulting in a larger wear scar diameter (WSD) than the MoDTC/PAO6 blend. At 25 °C, MoDTC achieves optimal lubrication, reducing the COF and WSD of neat DIOS by 50.0% and 23.3%, respectively. At 75 °C, COF reduction reaches 61.5%; at 125 °C, despite severe fluctuations in the friction curve, the WSD remains smaller than that of neat DIOS, indicating sustained anti‑wear capability. Combined with multiple modern characterizations, the underlying lubrication mechanisms is clarified: at low‑to‑medium temperatures, MoDTC preferentially generates a dense tribofilm dominated by layered MoS2; at elevated temperatures, the tribofilm transforms into a composite of MoO3 and MoSxOy. Despite increasing the COF, this composite tribofilms retain excellent load‑bearing and anti‑adhesion properties to mitigate severe wear. This study provides guidance for optimizing MoDTC synthesis, polarity matching, and tribofilm regulation, facilitating its wide application in lubrication systems.
- 10 October 2026
- Published by Tsinghua University Press in Friction
Open AccessEfficient one-pot synthesis of molybdenum dialkyl dithiocarbamate and investigation on evolution mechanism of tribofilms in ester-based lubricants
Base oil polarity critically governs additive solubility, interfacial adsorption, and tribochemical reactions, which collectively determine friction, wear, and component service life. In this study, molybdenum dialkyldithiocarbamate (MoDTC) was synthesized via a facile one-pot route. Its dispersion stability and tribological properties were compared in two base oils with distinct polarities: polar diisooctyl sebacate (DIOS) and nonpolar polyalphaolefin (PAO6). The tribological behavior of the MoDTC/DIOS blend was further evaluated under variable applied loads and temperatures. The results reveal that MoDTC delivers superior friction-reducing and anti-wear performance in nonpolar PAO6, attributed to stable adsorption on friction surfaces and tribochemical decomposition into protective tribofilms. In contrast, polar DIOS enables the MoDTC/DIOS blend to reach a steady friction coefficient (COF) much faster, with a drastically shortened running-in stage. Cross-sectional characterizations demonstrate that the polar DIOS environment accelerates MoDTC decomposition and rapid formation of an amorphous Mo- and S-containing tribofilm, accounting for the sharp COF decline. Nevertheless, this amorphous tribofilm exhibits low load-bearing capacity and cannot effectively suppress interfacial wear, resulting in a larger wear scar diameter (WSD) than the MoDTC/PAO6 blend. At 25 °C, MoDTC achieves optimal lubrication, reducing the COF and WSD of neat DIOS by 50.0% and 23.3%, respectively. At 75 °C, COF reduction reaches 61.5%; at 125 °C, despite severe fluctuations in the friction curve, the WSD remains smaller than that of neat DIOS, indicating sustained anti‑wear capability. Combined with multiple modern characterizations, the underlying lubrication mechanisms is clarified: at low‑to‑medium temperatures, MoDTC preferentially generates a dense tribofilm dominated by layered MoS2; at elevated temperatures, the tribofilm transforms into a composite of MoO3 and MoSxOy. Despite increasing the COF, this composite tribofilms retain excellent load‑bearing and anti‑adhesion properties to mitigate severe wear. This study provides guidance for optimizing MoDTC synthesis, polarity matching, and tribofilm regulation, facilitating its wide application in lubrication systems.
- 12 March 2026
- Published by Wiley in Lubrication Science
Preparation of Oleic Acid‐Modified Graphite/Biodiesel Composite Lubricants and Its Synergistic Lubrication Mechanism in Water Based Drilling Fluids
With the gradual shift of global oil and gas exploration and development toward offshore, deep, ultra‐deep, and high‐displacement unconventional wells, the drilling process is increasingly challenged by excessive torque and high frictional resistance, which severely restrict drilling efficiency and operational safety. Meanwhile, under the background of increasingly stringent global environmental protection regulations, traditional oil‐based drilling fluid lubricants are gradually becoming inapplicable due to poor biodegradability and severe environmental pollution. Thus, developing high‐performance, environmentally friendly water‐based drilling fluid lubricant has become an urgent demand in the oil and gas drilling industry. To address this critical issue, this study proposes a two‐step strategy for modified graphite/biodiesel (MG/BD) composite lubricants: graphite was first surface‐modified with oleic acid to enhance its dispersibility and compatibility with organic phases, followed by compounding with biodiesel (a renewable biomass derivative) to obtain the composite lubricant. Systematic tribological tests were conducted to assess the lubricating performance of the composite lubricant. The results demonstrate that the MG/BD composite lubricant exhibits excellent friction‐reducing and anti‐wear properties at room temperature. When 1.0 wt% of the MG/BD composite lubricant with 60% MG content was added to the base slurry, the friction coefficient was reduced by 89% compared with the base slurry without lubricant; even after thermal aging at 150°C for 16 h, the friction coefficient still maintained a 73% reduction efficiency, indicating good thermal stability. Comparative experiments with commercial water‐based drilling fluid lubricants further confirm that the MG/BD composite lubricant has superior lubricating performance. The mechanism analysis reveals that the excellent tribological properties of the composite lubricant stem from a synergistic effect of bentonite dispersion regulation and solid–liquid composite lubrication. On one hand, BD components adsorb on bentonite surfaces to form a steric hindrance layer, while nano‐MG particles intercalate into bentonite interlayers, jointly inhibiting bentonite agglomeration and enhancing drilling fluid stability. On the other hand, a stable solid–liquid composite lubricating film is formed on the metal friction pair surface: a composite solid film consisting of a continuous graphite solid lubricating film and an inorganic reaction film formed by iron oxides was formed to reduce direct contact between friction pairs. Simultaneously, BD forms a complementary liquid lubricating film to fill micro‐pits and reduce shear resistance between the solid film and metal substrate. Even after 150°C aging, partial decomposition of BD and increased defects in the graphite film slightly degrade anti‐wear performance, but the residual solid–liquid composite film still maintains effective lubrication. This study provides a novel approach and technical support for the development of high‐performance, environmentally friendly water‐based drilling fluid lubricants, and has broad application prospects in unconventional well drilling operations.
- 12 March 2026
- Published by Wiley in Lubrication Science
Preparation of Oleic Acid‐Modified Graphite/Biodiesel Composite Lubricants and Its Synergistic Lubrication Mechanism in Water Based Drilling Fluids
With the gradual shift of global oil and gas exploration and development toward offshore, deep, ultra‐deep, and high‐displacement unconventional wells, the drilling process is increasingly challenged by excessive torque and high frictional resistance, which severely restrict drilling efficiency and operational safety. Meanwhile, under the background of increasingly stringent global environmental protection regulations, traditional oil‐based drilling fluid lubricants are gradually becoming inapplicable due to poor biodegradability and severe environmental pollution. Thus, developing high‐performance, environmentally friendly water‐based drilling fluid lubricant has become an urgent demand in the oil and gas drilling industry. To address this critical issue, this study proposes a two‐step strategy for modified graphite/biodiesel (MG/BD) composite lubricants: graphite was first surface‐modified with oleic acid to enhance its dispersibility and compatibility with organic phases, followed by compounding with biodiesel (a renewable biomass derivative) to obtain the composite lubricant. Systematic tribological tests were conducted to assess the lubricating performance of the composite lubricant. The results demonstrate that the MG/BD composite lubricant exhibits excellent friction‐reducing and anti‐wear properties at room temperature. When 1.0 wt% of the MG/BD composite lubricant with 60% MG content was added to the base slurry, the friction coefficient was reduced by 89% compared with the base slurry without lubricant; even after thermal aging at 150°C for 16 h, the friction coefficient still maintained a 73% reduction efficiency, indicating good thermal stability. Comparative experiments with commercial water‐based drilling fluid lubricants further confirm that the MG/BD composite lubricant has superior lubricating performance. The mechanism analysis reveals that the excellent tribological properties of the composite lubricant stem from a synergistic effect of bentonite dispersion regulation and solid–liquid composite lubrication. On one hand, BD components adsorb on bentonite surfaces to form a steric hindrance layer, while nano‐MG particles intercalate into bentonite interlayers, jointly inhibiting bentonite agglomeration and enhancing drilling fluid stability. On the other hand, a stable solid–liquid composite lubricating film is formed on the metal friction pair surface: a composite solid film consisting of a continuous graphite solid lubricating film and an inorganic reaction film formed by iron oxides was formed to reduce direct contact between friction pairs. Simultaneously, BD forms a complementary liquid lubricating film to fill micro‐pits and reduce shear resistance between the solid film and metal substrate. Even after 150°C aging, partial decomposition of BD and increased defects in the graphite film slightly degrade anti‐wear performance, but the residual solid–liquid composite film still maintains effective lubrication. This study provides a novel approach and technical support for the development of high‐performance, environmentally friendly water‐based drilling fluid lubricants, and has broad application prospects in unconventional well drilling operations.
- 19 December 2024
- Published by Springer Nature in Tribology Letters
- Vol. 73 (1) , 1-12
Design, Synthesis and Tribological Properties of Fatty Acid Diethanolamide Borate Esters with Different Carbon Chain Lengths
- 19 December 2024
- Published by Springer Nature in Tribology Letters
- Vol. 73 (1) , 1-12
Design, Synthesis and Tribological Properties of Fatty Acid Diethanolamide Borate Esters with Different Carbon Chain Lengths
- 25 November 2024
- Published by Springer Nature in Tribology Letters
- Vol. 73 (1) , 1-11
In-situ Synthesis of Nickel Nanoparticles in Olive Oil and Study of Their Tribological Properties as Vegetable Oil Additives
- 25 November 2024
- Published by Springer Nature in Tribology Letters
- Vol. 73 (1) , 1-11
In-situ Synthesis of Nickel Nanoparticles in Olive Oil and Study of Their Tribological Properties as Vegetable Oil Additives
- Open Access
- 24 August 2023
- Published by Tsinghua University Press in Friction
- Vol. 12 (3) , 474-489
Tribological properties and tribomechanism of nickel nanoparticles in-situ synthesized in rapeseed oil
Nickel (Ni) nanoparticles can be enriched on the surface of iron-based frictional pairs, which provides the possibility to get rid of the competitive adsorption between the polar species of vegetable oil and the surface-active nano-additives thereon. In this paper, nickel acetylacetonate was used as a precursor to in-situ synthesize nickel nanoparticles with an average diameter of about 12 nm in rapeseed oil (RO) as the reducing agent, surface modifier, and solvent as well. The tribological properties of the as-synthesized Ni nanoparticles were evaluated with a four-ball tribometer, and their tribomechanism was investigated based on the characterizations of the tribofilm on rubbed steel surfaces by the scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). It was found that the Ni nanoparticles in-situ prepared in the RO with a mass fraction of 0.3% can reduce the wear scar diameter (WSD) of the steel ball by 36%. This is because, on the one hand, the Ni nanoparticles are adsorbed on the rubbed steel surfaces to repair or fill up the micro-pits and grooves thereon. On the other hand, Ni nanoparticles participate in tribochemical reactions with atmospheric O and steel substrate to form the tribochemical reaction film on the rubbed steel surfaces with the assistance of friction-induced heat and applied normal load. In addition, an amorphous carbon film is formed on the rubbed surface via the carbonization of base oil under the catalysis of Ni nanoparticles. The adsorbed Ni layer, the tribochemical reaction film, and the carbon layer comprise a composite tribofilm composed of amorphous carbon, polar fatty acid, metallic nickel, iron oxides, and nickel oxides on the rubbed steel surfaces, which contributes to significantly improving the antiwear ability and load-carrying capacity of the RO for the steel–steel sliding pair.
- 24 August 2023
- Published by Tsinghua University Press in Friction
- Vol. 12 (3) , 474-489
Open AccessTribological properties and tribomechanism of nickel nanoparticles in-situ synthesized in rapeseed oil
Nickel (Ni) nanoparticles can be enriched on the surface of iron-based frictional pairs, which provides the possibility to get rid of the competitive adsorption between the polar species of vegetable oil and the surface-active nano-additives thereon. In this paper, nickel acetylacetonate was used as a precursor to in-situ synthesize nickel nanoparticles with an average diameter of about 12 nm in rapeseed oil (RO) as the reducing agent, surface modifier, and solvent as well. The tribological properties of the as-synthesized Ni nanoparticles were evaluated with a four-ball tribometer, and their tribomechanism was investigated based on the characterizations of the tribofilm on rubbed steel surfaces by the scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). It was found that the Ni nanoparticles in-situ prepared in the RO with a mass fraction of 0.3% can reduce the wear scar diameter (WSD) of the steel ball by 36%. This is because, on the one hand, the Ni nanoparticles are adsorbed on the rubbed steel surfaces to repair or fill up the micro-pits and grooves thereon. On the other hand, Ni nanoparticles participate in tribochemical reactions with atmospheric O and steel substrate to form the tribochemical reaction film on the rubbed steel surfaces with the assistance of friction-induced heat and applied normal load. In addition, an amorphous carbon film is formed on the rubbed surface via the carbonization of base oil under the catalysis of Ni nanoparticles. The adsorbed Ni layer, the tribochemical reaction film, and the carbon layer comprise a composite tribofilm composed of amorphous carbon, polar fatty acid, metallic nickel, iron oxides, and nickel oxides on the rubbed steel surfaces, which contributes to significantly improving the antiwear ability and load-carrying capacity of the RO for the steel–steel sliding pair.
- Open Access
- 11 October 2022
- Published by Springer Nature in Research Square
Preparation of Nanofluid of Lanthanum Borate Nanosheets and Investigation of Its Tribological Properties and Tribomechamisms in Different Base Oils
Oleic acid-modified lanthanum borate nanosheets (OA-LBNs) were prepared by simple surface modification technology combined with precipitation method. The structure of the as-prepared light yellow transparent nanofluid of OA-LBNs was analyzed by Fourier transform infrared spectroscopy and transmission electron microscopy, and its thermal stability was evaluated by thermogravimetric analysis. Moreover, the tribological properties of OA-LBNs nanofluid as the lubricant additive in diisooctylsebacate (DIOS), poly-α-olefin (PAO4), and rapeseed oil (RO) were evaluated with a four-ball friction and wear tester, and its tribomechanisms in the three kinds of base oils were also discussed. The results show that OA-LBNs nanofluid exhibits good antiwear ability in the three kinds of base oils; and in particular, OA-LBNs nanofluid added in PAO4 shows the best antiwear ability. The tribological properties of the OA-LBNs nanofluid as the lubricant additive are dependent on the nature of the base oils. Namely, the polarity of the base oil influences the adsorption of the OA-LBNs nanofluid on the rubbed steel surface, thereby affecting the composition of the tribofilm formed on the rubbed steel surface and resulting in changes in tribological properties.
- 11 October 2022
- Published by Springer Nature in Research Square
Open AccessPreparation of Nanofluid of Lanthanum Borate Nanosheets and Investigation of Its Tribological Properties and Tribomechamisms in Different Base Oils
Oleic acid-modified lanthanum borate nanosheets (OA-LBNs) were prepared by simple surface modification technology combined with precipitation method. The structure of the as-prepared light yellow transparent nanofluid of OA-LBNs was analyzed by Fourier transform infrared spectroscopy and transmission electron microscopy, and its thermal stability was evaluated by thermogravimetric analysis. Moreover, the tribological properties of OA-LBNs nanofluid as the lubricant additive in diisooctylsebacate (DIOS), poly-α-olefin (PAO4), and rapeseed oil (RO) were evaluated with a four-ball friction and wear tester, and its tribomechanisms in the three kinds of base oils were also discussed. The results show that OA-LBNs nanofluid exhibits good antiwear ability in the three kinds of base oils; and in particular, OA-LBNs nanofluid added in PAO4 shows the best antiwear ability. The tribological properties of the OA-LBNs nanofluid as the lubricant additive are dependent on the nature of the base oils. Namely, the polarity of the base oil influences the adsorption of the OA-LBNs nanofluid on the rubbed steel surface, thereby affecting the composition of the tribofilm formed on the rubbed steel surface and resulting in changes in tribological properties.
- 1 December 2020
- Published by Cambridge University Press (CUP) in Clays and Clay Minerals
- Vol. 68 (6) , 646-655
Co-Modification of Bentonite by CTAB and Silane and its Performance in Oil-Based Drilling Mud
The stability, dispersion, and rheological properties of clay suspensions are important in the process of drilling. Organic clays were obtained traditionally by cation exchange, which is thermally unstable due to weak electrostatic interaction between the cationic surfactant and clay minerals. The purpose of the present study was to yield a stable and well dispersed organic bentonite (OBent) as a rheological additive for oil-based drilling mud. The co-modified method was used to modify bentonite by a cationic surfactant (cetyltrimethoxyammonium bromide: CTAB) and a silane coupling agent (hexadecyltrimethoxysilane: HDTMS). Firstly, the basal spacing of bentonite was enlarged by intercalation of CTAB, and the thermal stability of bentonite was improved by covalent bonds of HDTMS onto the bentonite platelets. The as-prepared OBent was characterized by infrared analysis, X-ray diffraction analysis, thermogravimetric analysis, and scanning electron microscopy. The hydrophobicity, solubility, viscosity, and tribological performance of the OBent were also recorded. The test results showed that the hydrophobicity of the co-modified bentonite was improved significantly, and was greater than that of bentonite modified with single surfactant CTAB or HDTMS. The bentonite modified by the surfactant together with the silane coupling agent had stable rheology and a lower coefficient of friction than the single surfactant-modified bentonite because more HDTMS entered into the interlayer spaces and formed chemical bonds at the inner surface of platelets.
- 1 December 2020
- Published by Cambridge University Press (CUP) in Clays and Clay Minerals
- Vol. 68 (6) , 646-655
Co-Modification of Bentonite by CTAB and Silane and its Performance in Oil-Based Drilling Mud
The stability, dispersion, and rheological properties of clay suspensions are important in the process of drilling. Organic clays were obtained traditionally by cation exchange, which is thermally unstable due to weak electrostatic interaction between the cationic surfactant and clay minerals. The purpose of the present study was to yield a stable and well dispersed organic bentonite (OBent) as a rheological additive for oil-based drilling mud. The co-modified method was used to modify bentonite by a cationic surfactant (cetyltrimethoxyammonium bromide: CTAB) and a silane coupling agent (hexadecyltrimethoxysilane: HDTMS). Firstly, the basal spacing of bentonite was enlarged by intercalation of CTAB, and the thermal stability of bentonite was improved by covalent bonds of HDTMS onto the bentonite platelets. The as-prepared OBent was characterized by infrared analysis, X-ray diffraction analysis, thermogravimetric analysis, and scanning electron microscopy. The hydrophobicity, solubility, viscosity, and tribological performance of the OBent were also recorded. The test results showed that the hydrophobicity of the co-modified bentonite was improved significantly, and was greater than that of bentonite modified with single surfactant CTAB or HDTMS. The bentonite modified by the surfactant together with the silane coupling agent had stable rheology and a lower coefficient of friction than the single surfactant-modified bentonite because more HDTMS entered into the interlayer spaces and formed chemical bonds at the inner surface of platelets.