Nur Dalilla Nordin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Nur Dalilla Nordin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Fairuz Abdullah
2 shared publications- Fairuz Abdullah
Institute of Power Engineering, Universiti Tenaga Nasional, Kajang, Malaysia
2 shared publications Mohd Saiful Dzulkefly Zan
2 shared publications- Mohd Saiful Dzulkefly Zan
Center of Advanced Electronic and Communication Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia
2 shared publications Ahmad Ashrif A Bakar
Electronics & Systems Engineering, Faculty of Engineering & Build Environment, Universiti Kebangsaan Malaysia, Bandar Baru Bangi, Malaysia
1 shared publication- Ahmad Ashrif Abu Bakar
Photonics Technology Laboratory, Department of Electrical, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor, Malaysia
1 shared publication
Latest Publications
- Open Access
Improving Prediction Accuracy and Extraction Precision of Frequency Shift from Low-SNR Brillouin Gain Spectra in Distributed Structural Health Monitoring
In this paper, we studied the possibility of increasing the Brillouin frequency shift (BFS) detection accuracy in distributed fibre-optic sensors by the separate and joint use of different algorithms for finding the spectral maximum: Lorentzian curve fitting (LCF, including the Levenberg–Marquardt (LM) method), the backward correlation technique (BWC) and a machine learning algorithm, the generalized linear model (GLM). The study was carried out on real spectra subjected to the subsequent addition of extreme digital noise. The precision and accuracy of the LM and BWC methods were studied by varying the signal-to-noise ratios (SNRs) and by incorporating the GLM method into the processing steps. It was found that the use of methods in sequence gives a gain in the accuracy of determining the sensor temperature from tenths to several degrees Celsius (or MHz in BFS scale), which is manifested for signal-to-noise ratios within 0 to 20 dB. We have found out that the double processing (BWC + GLM) is more effective for positive SNR values (in dB): it gives a gain in BFS measurement precision near 0.4 °C (428 kHz or 9.3 ); for BWC + GLM, the difference of precisions between single and double processing for SNRs below 2.6 dB is about 1.5 °C (1.6 MHz or 35 ). In this case, double processing is more effective for all SNRs. The described technique’s potential application in structural health monitoring (SHM) of concrete objects and different areas in metrology and sensing were also discussed.Open AccessImproving Prediction Accuracy and Extraction Precision of Frequency Shift from Low-SNR Brillouin Gain Spectra in Distributed Structural Health Monitoring
In this paper, we studied the possibility of increasing the Brillouin frequency shift (BFS) detection accuracy in distributed fibre-optic sensors by the separate and joint use of different algorithms for finding the spectral maximum: Lorentzian curve fitting (LCF, including the Levenberg–Marquardt (LM) method), the backward correlation technique (BWC) and a machine learning algorithm, the generalized linear model (GLM). The study was carried out on real spectra subjected to the subsequent addition of extreme digital noise. The precision and accuracy of the LM and BWC methods were studied by varying the signal-to-noise ratios (SNRs) and by incorporating the GLM method into the processing steps. It was found that the use of methods in sequence gives a gain in the accuracy of determining the sensor temperature from tenths to several degrees Celsius (or MHz in BFS scale), which is manifested for signal-to-noise ratios within 0 to 20 dB. We have found out that the double processing (BWC + GLM) is more effective for positive SNR values (in dB): it gives a gain in BFS measurement precision near 0.4 °C (428 kHz or 9.3 ); for BWC + GLM, the difference of precisions between single and double processing for SNRs below 2.6 dB is about 1.5 °C (1.6 MHz or 35 ). In this case, double processing is more effective for all SNRs. The described technique’s potential application in structural health monitoring (SHM) of concrete objects and different areas in metrology and sensing were also discussed. - Open Access
Comparative Analysis on the Deployment of Machine Learning Algorithms in the Distributed Brillouin Optical Time Domain Analysis (BOTDA) Fiber Sensor
This paper demonstrates a comparative analysis of five machine learning (ML) algorithms for improving the signal processing time and temperature prediction accuracy in Brillouin optical time domain analysis (BOTDA) fiber sensor. The algorithms analyzed were generalized linear model (GLM), deep learning (DL), random forest (RF), gradient boosted trees (GBT), and support vector machine (SVM). In this proof-of-concept experiment, the performance of each algorithm was investigated by pairing Brillouin gain spectrum (BGS) with its corresponding temperature reading in the training dataset. It was found that all of the ML algorithms have significantly reduced the signal processing time to be between 3.5 and 655 times faster than the conventional Lorentzian curve fitting (LCF) method. Furthermore, the temperature prediction accuracy and temperature measurement precision made by some algorithms were comparable, and some were even better than the conventional LCF method. The results obtained from the experiments would provide some general idea in deploying ML algorithm for characterizing the Brillouin-based fiber sensor signals.
Open AccessComparative Analysis on the Deployment of Machine Learning Algorithms in the Distributed Brillouin Optical Time Domain Analysis (BOTDA) Fiber Sensor
This paper demonstrates a comparative analysis of five machine learning (ML) algorithms for improving the signal processing time and temperature prediction accuracy in Brillouin optical time domain analysis (BOTDA) fiber sensor. The algorithms analyzed were generalized linear model (GLM), deep learning (DL), random forest (RF), gradient boosted trees (GBT), and support vector machine (SVM). In this proof-of-concept experiment, the performance of each algorithm was investigated by pairing Brillouin gain spectrum (BGS) with its corresponding temperature reading in the training dataset. It was found that all of the ML algorithms have significantly reduced the signal processing time to be between 3.5 and 655 times faster than the conventional Lorentzian curve fitting (LCF) method. Furthermore, the temperature prediction accuracy and temperature measurement precision made by some algorithms were comparable, and some were even better than the conventional LCF method. The results obtained from the experiments would provide some general idea in deploying ML algorithm for characterizing the Brillouin-based fiber sensor signals.
- 1 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-14
Fast temperature extraction approach for BOTDA using Generalized Linear Model
Fast temperature extraction approach for Brillouin optical time domain analyzer (BOTDA) system using Generalized Linear Model (GLM) is demonstrated experimentally. The training dataset for GLM is designed in order to make it feasible for the measurand extraction. The advantage of using this method is that it is fast as compared to conventional method where the determination of Brillouin frequency shift (BFS) and then translating BFS to temperature or strain can be eliminated. The results of temperature distribution along the fiber between the conventional method and GLM shows comparable accuracy.
- 1 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 13-14
Fast temperature extraction approach for BOTDA using Generalized Linear Model
Fast temperature extraction approach for Brillouin optical time domain analyzer (BOTDA) system using Generalized Linear Model (GLM) is demonstrated experimentally. The training dataset for GLM is designed in order to make it feasible for the measurand extraction. The advantage of using this method is that it is fast as compared to conventional method where the determination of Brillouin frequency shift (BFS) and then translating BFS to temperature or strain can be eliminated. The results of temperature distribution along the fiber between the conventional method and GLM shows comparable accuracy.
- 7 January 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9442, 94421K
Multi-layer surface profiling using gated wavefront sensing
Recently, multi-layer surface profiling and inspection has been considered an emerging topic that can be used to solve various manufacturing inspection problems, such as graded index lenses, TSV (Thru-Silicon Via), and optical coating. In our study, we proposed a gated wavefront sensing approach to estimate the multi-layer surface profile. In this paper, we set up an experimental platform to validate our theoretical models and methods. Our test bed consists of pulse laser, collimator, prism, well-defined focusing lens, testing specimen, and gated wavefront sensing assembly (e.g., lenslet and gated camera). Typical wavefront measurement steps are carried out for the gated system, except the reflectance is timed against its time of flight as well as its intensity profile. By synchronizing the laser pulses to the camera gate time, it is possible to discriminate a multi-layer wavefront from its neighbouring discrete layer reflections.
- 7 January 2015
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9442, 94421K
Multi-layer surface profiling using gated wavefront sensing
Recently, multi-layer surface profiling and inspection has been considered an emerging topic that can be used to solve various manufacturing inspection problems, such as graded index lenses, TSV (Thru-Silicon Via), and optical coating. In our study, we proposed a gated wavefront sensing approach to estimate the multi-layer surface profile. In this paper, we set up an experimental platform to validate our theoretical models and methods. Our test bed consists of pulse laser, collimator, prism, well-defined focusing lens, testing specimen, and gated wavefront sensing assembly (e.g., lenslet and gated camera). Typical wavefront measurement steps are carried out for the gated system, except the reflectance is timed against its time of flight as well as its intensity profile. By synchronizing the laser pulses to the camera gate time, it is possible to discriminate a multi-layer wavefront from its neighbouring discrete layer reflections.