Ming-Che Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ming-Che Lin has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Chia-Chieh Cheng
Department of Mechanical Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 80778, Taiwan
1 shared publication - Ching-Chien Huang
Department of Mechanical Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, TAIWAN
1 shared publication - Ruei-Fong Lin
Department of Mechanical Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 807618, Taiwan
1 shared publication - Tsung-Han Ho
Department of Chemical and Materials Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 807, Taiwan
1 shared publication
Latest Publications
- Open Access
Design Analysis of Heat Sink Using the Field Synergy Principle and Multitarget Response Surface Methodology
This study describes a novel heat sink design approach employs the field synergy concept and multitarget response surface methodology (RSM). The multiobjective response surface methodology can be used to determine the simulation equations that will maximize the heat transfer of fins at various fin heights, fin angles, and fin circumferences, when considering the impact of jet flow heat exchange. The goal of the response value was to maintain the minimum possible average field coangle and fin temperature. The results show that the ideal heat sink size would be the following: fins with a height of 50 mm, an angle of 60 degrees, and the number of fins equal to five. We examined the impact of wall speed on the heat transfer caused by the field synergy angle. Our findings suggest that with the synchromesh of the display field, heat-dissipation efficiency rises.
Open AccessDesign Analysis of Heat Sink Using the Field Synergy Principle and Multitarget Response Surface Methodology
This study describes a novel heat sink design approach employs the field synergy concept and multitarget response surface methodology (RSM). The multiobjective response surface methodology can be used to determine the simulation equations that will maximize the heat transfer of fins at various fin heights, fin angles, and fin circumferences, when considering the impact of jet flow heat exchange. The goal of the response value was to maintain the minimum possible average field coangle and fin temperature. The results show that the ideal heat sink size would be the following: fins with a height of 50 mm, an angle of 60 degrees, and the number of fins equal to five. We examined the impact of wall speed on the heat transfer caused by the field synergy angle. Our findings suggest that with the synchromesh of the display field, heat-dissipation efficiency rises.
- Open Access
Study on the Application of the GTAW Process in Strengthening the Welding Quality of Short Duplex Stainless Pipe
This study focuses on the results of the welding process when the Taguchi method is added to the design of experimental welding parameters when creating the welding procedure for gas tungsten arc welding (GTAW) by ASME Code for duplex stainless steel (UNS31803). A Vickers hardness tester is employed to collect and convert the tensile strength data for each test piece (weld bead, base material, and heat-affected area). A ferritic rate meter can quickly determine the ferric contents, which affect corrosion resistance and susceptibility to cracking. The test data are entered into the Taguchi technique to analyze the influence of each component on the welding quality. The L9 (34) orthogonal table is used to design the parameters for the experiment. We fixed the same shielding gas and flow rate. Backing gas at root, workpiece clamping angle, heat input, and interlayer temperature are employed as control factors for the four essential variables of the GTAW process. The ideal set of quality analysis and optimization parameters can be found. The welding parameters could be used to improve the welding quality of thin and short duplex stainless steel pipe fittings during argon welding.
Open AccessStudy on the Application of the GTAW Process in Strengthening the Welding Quality of Short Duplex Stainless Pipe
This study focuses on the results of the welding process when the Taguchi method is added to the design of experimental welding parameters when creating the welding procedure for gas tungsten arc welding (GTAW) by ASME Code for duplex stainless steel (UNS31803). A Vickers hardness tester is employed to collect and convert the tensile strength data for each test piece (weld bead, base material, and heat-affected area). A ferritic rate meter can quickly determine the ferric contents, which affect corrosion resistance and susceptibility to cracking. The test data are entered into the Taguchi technique to analyze the influence of each component on the welding quality. The L9 (34) orthogonal table is used to design the parameters for the experiment. We fixed the same shielding gas and flow rate. Backing gas at root, workpiece clamping angle, heat input, and interlayer temperature are employed as control factors for the four essential variables of the GTAW process. The ideal set of quality analysis and optimization parameters can be found. The welding parameters could be used to improve the welding quality of thin and short duplex stainless steel pipe fittings during argon welding.
- Open Access
- 24 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 8878
Design Study for a New Spanner
A replacement for the original F-spanner is designed using computer-aided engineering (CAE) and the Taguchi method. In the design process, the L9(34) orthogonal table was used for parameter design. Four control factors are used: outer diameter, bend radius, angle, and connected fillet. Each factor is set to three levels with numerical analysis using ANSYS software. After performing an optimization analysis for the combination parameters, the prototype is created by rapid-prototyping (RP) and is found to improve operational safety in a piping system.
- 24 September 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (19) , 8878
Open AccessDesign Study for a New Spanner
A replacement for the original F-spanner is designed using computer-aided engineering (CAE) and the Taguchi method. In the design process, the L9(34) orthogonal table was used for parameter design. Four control factors are used: outer diameter, bend radius, angle, and connected fillet. Each factor is set to three levels with numerical analysis using ANSYS software. After performing an optimization analysis for the combination parameters, the prototype is created by rapid-prototyping (RP) and is found to improve operational safety in a piping system.