Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Amvrosios G. Georgiadis has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An experimental and theoretical approach for the biogas dry reforming reaction using perovskite-derived La0.8X0.2NiO3-δ catalysts (X = Sm, Pr, Ce)

    by Amvrosios G. Georgiadis, Anastasios I. Tsiotsias, George I. Siakavelas, Nikolaos D. Charisiou, Benedikt Ehrhardt, Wen Wang, Victor Sebastian, Steven J. Hinder, Mark A. Baker, Simone Mascotto, et al.


  • Open Access

    CO2 Physisorption over an Industrial Molecular Sieve Zeolite: An Experimental and Theoretical Approach

    by Anastasios I. Tsiotsias, Amvrosios G. Georgiadis, Nikolaos D. Charisiou, Maria A. Goula

    The present work studies the adsorption of CO2 using a zeolitic industrial molecular sieve (IMS) with a high surface area. The effect of the CO2 feed concentration and the adsorption temperature in conjunction with multiple adsorption–desorption cycles was experimentally investigated. To assess the validity of the experimental results, theoretical calculations based on well-established equations were employed and the values of equilibrium, kinetic, and thermodynamic parameters are presented. Three additional column kinetic models were applied to the data obtained experimentally, in order to predict the breakthrough curves and thus facilitate process design. Results showed a negative correlation between temperature and adsorption capacity, indicating that physical adsorption takes place. Theoretical calculations revealed that the Langmuir isotherm, the Bangham kinetic model (i.e., pore diffusion is the rate-determining step), and the Thomas and Yoon–Nelson models were suitable to describe the CO2 adsorption process by the IMS. The IMS adsorbent material maintained its high CO2 adsorption capacity (>200 mg g−1) after multiple adsorption–desorption cycles, showing excellent regenerability and requiring only a mild desorption treatment (200 °C for 15 min) for regeneration.


  • Open Access

    A Mini-Review on Lanthanum–Nickel-Based Perovskite-Derived Catalysts for Hydrogen Production via the Dry Reforming of Methane (DRM)

    by Amvrosios G. Georgiadis, Nikolaos D. Charisiou, Maria A. Goula

    Given that the attempts to head toward a hydrogen economy are gathering pace, the dry reforming of methane (DRM) to produce hydrogen-rich syngas is a reaction that is worthy of investigation. Nickel-based catalysts have been extensively examined as a cost-effective solution for DRM, though they suffer from fast deactivation caused by coke accumulation. However, a number of published studies report high catalytic performance in terms of both activity and stability for La–Ni-based perovskite-derived catalysts used in DRM in comparison to other corresponding materials. In the work presented herein, a thorough analysis regarding the application of La–Ni-based perovskite catalysts for DRM is carried out. LaNiO3 is known for its anti-coking ability owing to the strong interaction between CO2 and La2O3. A further modification to improve the catalytic performance can be achieved by the partial or complete substitution of A or/and B sites of the perovskite catalysts. The latest developments with respect to this topic are also discussed in this manuscript. Even though the low surface area of perovskite catalysts has always been an obstacle for their commercialization, new supported and porous perovskite materials have recently emerged to address, at least partly, the challenge. Finally, conclusions and future outlooks for developing novel perovskite catalysts that may potentially pioneer new technology are included.


  • Biogas dry reforming over Ni/LnOx-type catalysts (Ln = La, Ce, Sm or Pr)

    by Amvrosios G. Georgiadis, Georgios I. Siakavelas, Anastasios I. Tsiotsias, Nikolaos D. Charisiou, Benedikt Ehrhardt, Wen Wang, Victor Sebastian, Steven J. Hinder, Mark A. Baker, Simone Mascotto, et al.


  • Open Access

    Selective Catalytic Reduction of NOx over Perovskite-Based Catalysts Using CxHy(Oz), H2 and CO as Reducing Agents—A Review of the Latest Developments

    by Ioannis V. Yentekakis, Amvrosios G. Georgiadis, Catherine Drosou, Nikolaos D. Charisiou, Maria A. Goula

    Selective catalytic reduction (SCR) is probably the most widespread process for limiting NOx emissions under lean conditions (O2 excess) and, in addition to the currently used NH3 or urea as a reducing agent, many other alternative reductants could be more promising, such as CxHy/CxHyOz, H2 and CO. Different catalysts have been used thus far for NOx abatement from mobile (automotive) and stationary (fossil fuel combustion plants) sources, however, perovskites demand considerable attention, partly due to their versatility to combine and incorporate various chemical elements in their lattice that favor deNOx catalysis. In this work, the CxHy/CxHyOz−, H2−, and CO-SCR of NOx on perovskite-based catalysts is reviewed, with particular emphasis on the role of the reducing agent nature and perovskite composition. An effort has also been made to further discuss the correlation between the physicochemical properties of the perovskite-based catalysts and their deNOx activity. Proposed kinetic models are presented as well, that delve deeper into deNOx mechanisms over perovskite-based catalysts and potentially pave the way for further improving their deNOx efficiency.


  • Open Access

    Synthesis and Mathematical Modelling of the Preparation Process of Nickel-Alumina Catalysts with Egg-Shell Structures for Syngas Production via Reforming of Clean Model Biogas

    by Angeliki I. Latsiou, Olga A. Bereketidou, Nikolaos D. Charisiou, Amvrosios G. Georgiadis, Dimitrios G. Avraam, Maria A. Goula

    For the work presented herein nickel catalysts supported on γ-alumina extrudates (Ni/Al) with an egg-shell structure were prepared, using a modified Equilibrium Deposition Filtration (EDF) technique. Their performance was compared, for the biogas dry reforming reaction, with corresponding Ni/Al catalysts with a uniform structure, synthesized via the conventional wet impregnation method. The bulk and surface physicochemical characteristics of all final catalysts were determined using ICP-AES, N2 adsorption-desorption isotherms, XRD, SEM, and TEM. A theoretical model describing the impregnation process for the EDF extrudates, based on the Lee and Aris model, was also developed. It was concluded that following specific impregnation conditions, the egg-shell macro-distributions can be successfully predicted, in agreement with the experimental results. It was shown that the Ni/Al catalysts with an egg-shell structure had a higher H2 yield in comparison with the ones with a uniform structure. The difference in catalytic performance was attributed to the improved surface and structural properties of the egg-shell catalysts, resulting from the modified EDF technique used for their preparation.


  • Cost‐Effective Adsorption of Oxidative Coupling‐Derived Ethylene Using a Molecular Sieve

    by Georgios I. Siakavelas, Amvrosios G. Georgiadis, Nikolaos D. Charisiou, Ioannis V. Yentekakis, Maria A. Goula

    The adsorption of ethylene (C2H4) from a mixture simulating the products obtained during the oxidative coupling of CH4 using a commercial molecular sieve (MOS) is investigated. A joint experimental and theoretical approach has been employed. The adsorbent's trapping capacity decreases at higher temperatures, while the breakpoint time drops when the inlet C2H4 concentration increases. The Dubinin‐Radushkevich isotherm model can better describe the adsorption of C2H4 onto the MOS. Pore diffusion is the rate‐determining step given that the Bangham's kinetic model was the more suitable for this adsorption process. Finally, the low activation energy obtained corroborates the predominance of physical adsorption.


  • Open Access

    Adsorption of Hydrogen Sulfide at Low Temperatures Using an Industrial Molecular Sieve: An Experimental and Theoretical Study

    by Amvrosios G. Georgiadis, Nikolaos D. Charisiou, Safa Gaber, Kyriaki Polychronopoulou, Ioannis V. Yentekakis, Maria A. Goula


  • Open Access

    Removal of Hydrogen Sulfide (H2S) Using MOFs: A Review of the Latest Developments

    by Amvrosios G. Georgiadis, Nikolaos D. Charisiou, Ioannis V. Yentekakis, Maria A. Goula

    The removal of hydrogen sulfide (H2S) from gas streams with varying overall pressure and H2S concentrations is a long-standing challenge faced by the oil and gas industries. The present work focuses on H2S capture using metal–organic frameworks (MOFs), in an effort to shed light on their potential as adsorbents in the field of gas storage and separation. MOFs hold great promise as they make possible the design of structures from organic and inorganic units, but also, they have provided an answer to a long-time challenging issue, i.e., how to design extended structures of materials. Moreover, the functionalization of the MOF’s surface can result in increased H2S uptake. For example, the insertion of 1% of a fluorinated linker in MIL-101(Cr)-4F(1%) allows for enhanced H2S capture. Although noticeable efforts have been made in studying the adsorption capacity of H2S using MOFs, there is a clear need for gaining a deeper understanding in terms of their thermal conductivities and specific heats in order to design more stable adsorption beds, experiencing high exothermicity. Simply put, the exothermic nature of adsorption means that sharp rises in temperature can negatively affect the bed stability in the absence of sufficient heat transfer. The work presented herein provides a detailed discussion by thoroughly combining the existing literature on new developments in MOFs for H2S removal, and tries to provide insight into new areas for further research.


  • Open Access

    Hydrogen Sulfide (H2S) Removal via MOFs

    by Amvrosios G. Georgiadis, Nikolaos Charisiou, Ioannis V. Yentekakis, Maria A. Goula

    The removal of the environmentally toxic and corrosive hydrogen sulfide (H2S) from gas streams with varying overall pressure and H2S concentration is a long-standing challenge faced by the oil and gas industries. The present work focuses on H2S capture using a relatively new type of material, namely metal-organic frameworks (MOFs), in an effort to shed light on their potential as adsorbents in the field of gas storage and separation. MOFs hold great promise as they make possible the design of structures from organic and inorganic units, but also as they have provided an answer to a long-term challenging objective, i.e., how to design extended structures of materials. Moreover, in designing MOFs, one may functionalize the organic units and thus, in essence, create pores with different functionalities, and also to expand the pores in order to increase pore openings. The work presented herein provides a detailed discussion, by thoroughly combining the existing literature on new developments in MOFs for H2S removal, and tries to provide insight into new areas for further research.