Sergey A. Zverev
Sergey A. Zverev has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Sergey V. Andreev
Disinfectology Institute of F.F. Erisman FSCH of Rospotrebnadzor, 18a Nauchny Proezd, Moscow 117246, Russia
7 shared publications - Konstantin A. Sakharov
School of Materials Science and Engineering, Nanyang Technological University (NTU), 50 Nanyang Avenue, Singapore 639798, Singapore
6 shared publications - Anastasiya Sergeevna Ivanova
Federal State Educational Institution of Higher Education "Perm State National Research University
2 shared publications - Anna A. Selivanova
MIREA – Russian Technological University (M.V. Lomonosov Institute of Fine Chemical Technologies), Moscow, Russia
2 shared publications - Daria Savraeva
Casali Center for Applied Chemistry, Institute of Chemistry, The Hebrew University of Jerusalem, Jerusalem, Israel
2 shared publications - Vladimir Anatol'Evich Vinokurov
Gubkin Russian State University of Oil and Gas (National Research University), Moscow, Russia
2 shared publications
Latest Publications
- Open Access
- 10 December 2025
- Published by Federal Scientific Center for Hygiene F.F.Erisman in Disinfectology
- Vol. 1 (2) , 75-84
Toxicity and hazard study of disinfectants with inhalation exposure
Introduction. Exposure to disinfectants can negatively affect human and animal health, including respiratory tract irritation, inflammation, swelling, and allergic reactions.Objective. Establish the toxicity and danger of using working solutions of disinfectants with different chlorine dioxide content.Materials and Methods. Working solutions of disinfectants with chlorine dioxide content in concentrations from 0.01 to 0.075% were studied. In the study of working solutions in animals, the functional state of the nervous and respiratory systems was assessed. The chlorine dioxide content in the air was determined during surface treatment with a working solution with a chlorine dioxide concentration of 0.04%.Results. Hazard classes of working solutions of chlorine dioxide were established, which depended not only on the concentration of chlorine dioxide, but also on the initial composition of the components of disinfectants. Working solutions with a concentration of chlorine dioxide of 0.075% belong to the 2nd class of dangerous products, with a concentration of chlorine dioxide of 0.05–0.01% belong to the 4th class of low-risk products according to the Classification of the degree of inhalation hazard of disinfectants in the zone of acute biocidal action. The conducted sanitary and chemical studies of the studied disinfectants did not reveal a high content of chlorine dioxide in the air.Limitations. Only studies of the nervous and respiratory systems have been conducted, studies of the functional state of the liver and kidneys have not been conducted.Conclusion. A working solution with a chlorine dioxide concentration of 0.075% can be used by specialists in personal protective equipment in the absence of patients and the public. Working solutions with a concentration of 0.05–0.01% chlorine dioxide can be used both in the presence of patients and in everyday life. When treating surfaces with chlorine dioxide-based disinfectants by wiping, prolonged ventilation of rooms is not required to remove them.Ethics approval. Ethics Committee (subcommittee) Institute of Disinfection of the F.F. FNTSG. Rospotrebnadzor adopted and approved the program of toxicological studies of disinfectants for inhalation exposure to laboratory animals. The experiments were conducted in accordance with Directive 2010/63/EU of the European Parliament and of the Council of the European Union dated September 22, 2010 on the protection of animals used for scientific purposes, by order of the Ministry of Health Russia from 04/01/2016 No. 199n.Contribution: Pankratova G.P. — concept and design of the study, writing text; Bidevkina M.V. — general idea, writing the text and editing the article; Shaykhutdinova Z.K. — conducting research, collection and statistical processing of material; Morozov A.S. — concept and design of the study, collection and processing of material, writing text; Zverev S.A. — writing text; Vinogradova A.I. — statistical processing of material. All co-authors — integrity of all parts of the manuscript and approval of the manuscript final version.Funding. The study had no sponsorship and was carried out as part of a research project on the topic "Development of methods for the comprehensive assessment of the toxic effects of disinfectants and technologies for their use" (reg. No. R&D 023032900200-8-3.1.7).Conflict of interest. The authors declare that there are no obvious or potential conflicts of interest in relation to the publishing this article.Received: 07.07.2025 / Accepted: 26.10.2025 / Published: 10.12.2025
- 10 December 2025
- Published by Federal Scientific Center for Hygiene F.F.Erisman in Disinfectology
- Vol. 1 (2) , 75-84
Open AccessToxicity and hazard study of disinfectants with inhalation exposure
Introduction. Exposure to disinfectants can negatively affect human and animal health, including respiratory tract irritation, inflammation, swelling, and allergic reactions.Objective. Establish the toxicity and danger of using working solutions of disinfectants with different chlorine dioxide content.Materials and Methods. Working solutions of disinfectants with chlorine dioxide content in concentrations from 0.01 to 0.075% were studied. In the study of working solutions in animals, the functional state of the nervous and respiratory systems was assessed. The chlorine dioxide content in the air was determined during surface treatment with a working solution with a chlorine dioxide concentration of 0.04%.Results. Hazard classes of working solutions of chlorine dioxide were established, which depended not only on the concentration of chlorine dioxide, but also on the initial composition of the components of disinfectants. Working solutions with a concentration of chlorine dioxide of 0.075% belong to the 2nd class of dangerous products, with a concentration of chlorine dioxide of 0.05–0.01% belong to the 4th class of low-risk products according to the Classification of the degree of inhalation hazard of disinfectants in the zone of acute biocidal action. The conducted sanitary and chemical studies of the studied disinfectants did not reveal a high content of chlorine dioxide in the air.Limitations. Only studies of the nervous and respiratory systems have been conducted, studies of the functional state of the liver and kidneys have not been conducted.Conclusion. A working solution with a chlorine dioxide concentration of 0.075% can be used by specialists in personal protective equipment in the absence of patients and the public. Working solutions with a concentration of 0.05–0.01% chlorine dioxide can be used both in the presence of patients and in everyday life. When treating surfaces with chlorine dioxide-based disinfectants by wiping, prolonged ventilation of rooms is not required to remove them.Ethics approval. Ethics Committee (subcommittee) Institute of Disinfection of the F.F. FNTSG. Rospotrebnadzor adopted and approved the program of toxicological studies of disinfectants for inhalation exposure to laboratory animals. The experiments were conducted in accordance with Directive 2010/63/EU of the European Parliament and of the Council of the European Union dated September 22, 2010 on the protection of animals used for scientific purposes, by order of the Ministry of Health Russia from 04/01/2016 No. 199n.Contribution: Pankratova G.P. — concept and design of the study, writing text; Bidevkina M.V. — general idea, writing the text and editing the article; Shaykhutdinova Z.K. — conducting research, collection and statistical processing of material; Morozov A.S. — concept and design of the study, collection and processing of material, writing text; Zverev S.A. — writing text; Vinogradova A.I. — statistical processing of material. All co-authors — integrity of all parts of the manuscript and approval of the manuscript final version.Funding. The study had no sponsorship and was carried out as part of a research project on the topic "Development of methods for the comprehensive assessment of the toxic effects of disinfectants and technologies for their use" (reg. No. R&D 023032900200-8-3.1.7).Conflict of interest. The authors declare that there are no obvious or potential conflicts of interest in relation to the publishing this article.Received: 07.07.2025 / Accepted: 26.10.2025 / Published: 10.12.2025
- Open Access
Functional Polyacrylate Textile Coatings with N,N-Diethyl-3-methylbenzamide (DEET) Immobilized on Zirconia, Alumina and Silica Sorbents
In this study, polymer films based on the inorganic sorbents Al2O3, ZrO2 and SiO2-phenyl with repellent N,N-diethyl-3-methylbenzamide were prepared and used as functional textile coatings. The high sorption activity of oxides with respect to N,N-diethyl-3-methylbenzamide (63–239 mg/g) allows for the use of these compounds as repellent carrier materials, and their mixture with polyacrylates allows for the formation of functional coatings–polymer films. Scanning electron microscopy and Fourier transform infrared spectroscopy results revealed that the inorganic sorbents Al2O3, ZrO2 and SiO2-phenyl were successfully anchored in the polyacrylate structure, and the FTIR spectra confirmed the presence of repellent molecules. The thermal diffusion parameters of N,N-diethyl-3-methylbenzamide were also calculated via thermogravimetric analysis and high-performance liquid chromatography with diode array detection. The highest thermal diffusion rates and concentrations were observed for the material with Al2O3 (up to 148.3∙10−9 mol at 200 °C), and lower values for ZrO2 and SiO2-phenyl (up to 15.2∙10−9 mol and 34.3∙10−9 mol at 200 °C, respectively). The heat flux parameter Jf was also calculated according to Onsager’s theory and Fourier’s law. The release of repellent from polymeric materials can be achieved by applying less heat than that required to reach the boiling point of N,N-diethyl-3-methylbenzamide.
Open AccessFunctional Polyacrylate Textile Coatings with N,N-Diethyl-3-methylbenzamide (DEET) Immobilized on Zirconia, Alumina and Silica Sorbents
In this study, polymer films based on the inorganic sorbents Al2O3, ZrO2 and SiO2-phenyl with repellent N,N-diethyl-3-methylbenzamide were prepared and used as functional textile coatings. The high sorption activity of oxides with respect to N,N-diethyl-3-methylbenzamide (63–239 mg/g) allows for the use of these compounds as repellent carrier materials, and their mixture with polyacrylates allows for the formation of functional coatings–polymer films. Scanning electron microscopy and Fourier transform infrared spectroscopy results revealed that the inorganic sorbents Al2O3, ZrO2 and SiO2-phenyl were successfully anchored in the polyacrylate structure, and the FTIR spectra confirmed the presence of repellent molecules. The thermal diffusion parameters of N,N-diethyl-3-methylbenzamide were also calculated via thermogravimetric analysis and high-performance liquid chromatography with diode array detection. The highest thermal diffusion rates and concentrations were observed for the material with Al2O3 (up to 148.3∙10−9 mol at 200 °C), and lower values for ZrO2 and SiO2-phenyl (up to 15.2∙10−9 mol and 34.3∙10−9 mol at 200 °C, respectively). The heat flux parameter Jf was also calculated according to Onsager’s theory and Fourier’s law. The release of repellent from polymeric materials can be achieved by applying less heat than that required to reach the boiling point of N,N-diethyl-3-methylbenzamide.
- Open Access
Electroconductive Polymer Repellent Composites Based on N,N-Diethyl-3-methylbenzamide
In this study, electrically conductive polymer composites based on repellent N,N-diethyl-3-methylbenzamide with concentrations ranging from 6 to 30 wt% were developed. The electrical resistivity of repellent composites, as determined by electrochemical impedance spectra, ranges from 150 to 171 Ohm, which allows such materials to be used when a low voltage is applied. The study of the rheological properties of the obtained repellent composites and the analysis of the TGA curves demonstrated that the dynamic viscosity of the materials has a significant effect on the thermal diffusion of the repellent. The study of the thermal diffusion of N,N-diethyl-3-methylbenzamide demonstrated that a higher yield of repellent (up to 36.4 × 10−8 mol) is achieved when the material is applied in the form with the shortest conductor length of 14 mm. The graphs showing the relationship between the electrical flux and the concentration of N,N-diethyl-3-methylbenzamide, which was calculated via the Peltier and Thompson equations, show that, according to Onsager’s theory, the total flux of the substance is highest when a voltage is applied to the material with the shortest conductor length. Thus, the developed repellent composite is a promising material for protection against blood-sucking insects.
Open AccessElectroconductive Polymer Repellent Composites Based on N,N-Diethyl-3-methylbenzamide
In this study, electrically conductive polymer composites based on repellent N,N-diethyl-3-methylbenzamide with concentrations ranging from 6 to 30 wt% were developed. The electrical resistivity of repellent composites, as determined by electrochemical impedance spectra, ranges from 150 to 171 Ohm, which allows such materials to be used when a low voltage is applied. The study of the rheological properties of the obtained repellent composites and the analysis of the TGA curves demonstrated that the dynamic viscosity of the materials has a significant effect on the thermal diffusion of the repellent. The study of the thermal diffusion of N,N-diethyl-3-methylbenzamide demonstrated that a higher yield of repellent (up to 36.4 × 10−8 mol) is achieved when the material is applied in the form with the shortest conductor length of 14 mm. The graphs showing the relationship between the electrical flux and the concentration of N,N-diethyl-3-methylbenzamide, which was calculated via the Peltier and Thompson equations, show that, according to Onsager’s theory, the total flux of the substance is highest when a voltage is applied to the material with the shortest conductor length. Thus, the developed repellent composite is a promising material for protection against blood-sucking insects.
- 16 May 2024
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 302 (8) , 1259-1268
Study of sorption properties of zirconia, alumina, and silica in relation to repellents
- 16 May 2024
- Published by Springer Nature in Colloid and Polymer Science
- Vol. 302 (8) , 1259-1268
Study of sorption properties of zirconia, alumina, and silica in relation to repellents
- 1 January 2024
- Published by University Library in Kragujevac
- p. 297-300
ADVANCED MATERIALS AGAINST INSECTS AND TICKS
The use of materials that protect people from attacks by blood-sucking mosquitoes and ticks can significantly reduce the transmission of vector-borne infections. The results of this study demonstrate that inorganic oxides can be employed as repellent carrier substances to develop controlled-release materials. However, there was no direct correlation between the adsorption activity Qe (mg/g) and the concentration of N,N-diethyl-3-methylbenzamide (DEET) in the fabric(mg/m2). The most effective materials were produced using Al2O3 and ZrO2 oxides (more than 80 mg/m2 of DEET), as they contained the highest repellent concentration and therefore will have the greatest biological effect with the lowest economic costs. The materials have a high potential against blood-sucking insects and can be used in various conditions due to their controlled and prolonged effect.
- 1 January 2024
- Published by University Library in Kragujevac
- p. 297-300
ADVANCED MATERIALS AGAINST INSECTS AND TICKS
The use of materials that protect people from attacks by blood-sucking mosquitoes and ticks can significantly reduce the transmission of vector-borne infections. The results of this study demonstrate that inorganic oxides can be employed as repellent carrier substances to develop controlled-release materials. However, there was no direct correlation between the adsorption activity Qe (mg/g) and the concentration of N,N-diethyl-3-methylbenzamide (DEET) in the fabric(mg/m2). The most effective materials were produced using Al2O3 and ZrO2 oxides (more than 80 mg/m2 of DEET), as they contained the highest repellent concentration and therefore will have the greatest biological effect with the lowest economic costs. The materials have a high potential against blood-sucking insects and can be used in various conditions due to their controlled and prolonged effect.
- Open Access
- 2 August 2023
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 18 (3) , 254-264
Determination of chlorine-containing compounds in disinfectants using ion-exchange chromatography
Objectives. To develop a method for the determination of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions in solution; to determine the limits of detection and quantitation for ClO−, Cl−, ClO2−, ClO3−, and ClO4− ions; to evaluate the applicability of the developed method and its suitability for disinfectant analysis.Methods. Ionic chromatography using a conductometric detection system in isocratic elution mode.Results. The method developed for chromatographic determination of chlorine-containing ions can be used to quantify the content of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions. In isocratic elution mode at 7.5 mM NaOH and a flow rate of 0.4 mL/min, the content of chlorine-containing ions can be determined with high sensitivity. The presented method does not require the use of expensive equipment for the ultrasensitive analysis of the studied compounds.Conclusions. A novel method for the simultaneous determination of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions in case of their combined presence is proposed. The technique can be used to carry out routine control of the content of these disinfectant components during use, increasing their effectiveness at the same time as managing associated toxicological risks.
- 2 August 2023
- Published by RTU MIREA in Fine Chemical Technologies
- Vol. 18 (3) , 254-264
Open AccessDetermination of chlorine-containing compounds in disinfectants using ion-exchange chromatography
Objectives. To develop a method for the determination of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions in solution; to determine the limits of detection and quantitation for ClO−, Cl−, ClO2−, ClO3−, and ClO4− ions; to evaluate the applicability of the developed method and its suitability for disinfectant analysis.Methods. Ionic chromatography using a conductometric detection system in isocratic elution mode.Results. The method developed for chromatographic determination of chlorine-containing ions can be used to quantify the content of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions. In isocratic elution mode at 7.5 mM NaOH and a flow rate of 0.4 mL/min, the content of chlorine-containing ions can be determined with high sensitivity. The presented method does not require the use of expensive equipment for the ultrasensitive analysis of the studied compounds.Conclusions. A novel method for the simultaneous determination of hypochlorite, chloride, chlorite, chlorate, and perchlorate ions in case of their combined presence is proposed. The technique can be used to carry out routine control of the content of these disinfectant components during use, increasing their effectiveness at the same time as managing associated toxicological risks.
- 1 June 2023
- Published by National Organization of Disinfectionists in Disinfection affairs
- No. 2
On the possibility of using cationic surfactants to impart antimicrobial properties to textile materials
The COVID-19 pandemic has demonstrated the need for improved measures to prevent infectious diseases. Combating pathogens once they have been released into the environment is complicated by their widespread distribution. It is necessary to prevent the contamination of environmental objects. One possible way to do this is to create materials that have antimicrobial action without exposure to disinfectants and thus begin to have an antimicrobial effect on microorganisms immediately upon contact. Textile materials are widely used in medical organizations and are one of the factors of pathogenic microflora spreading. In this work, the possibility of using substances from the group of cationic surfactants to impart antimicrobial properties to textile materials was considered. Substances from different classes were used – tertiary amines, quaternary ammonium compounds, polymeric guanidine derivatives. The substances were applied from aqueous solutions using a laboratory analogue of a drying and a shirring machine. An acrylate binder with thermal initiation of polymerization was used to fix the active substances to the tissues. The content of the active substances in the tissues after application was determined by high-performance liquid chromatography. Antimicrobial activity of the obtained materials was checked by the agar plate method and the area of the growth retardation zone was estimated. Tissues containing N,N-bis(3-aminopropyl)dodecylamine showed the highest activity, tissues with poly (2-hydroxypropyl dimethylammonium) chloride the lowest. Keywords: antimicrobial materials, antimicrobial textile, HAI, cationic surfactants.
- 1 June 2023
- Published by National Organization of Disinfectionists in Disinfection affairs
- No. 2
On the possibility of using cationic surfactants to impart antimicrobial properties to textile materials
The COVID-19 pandemic has demonstrated the need for improved measures to prevent infectious diseases. Combating pathogens once they have been released into the environment is complicated by their widespread distribution. It is necessary to prevent the contamination of environmental objects. One possible way to do this is to create materials that have antimicrobial action without exposure to disinfectants and thus begin to have an antimicrobial effect on microorganisms immediately upon contact. Textile materials are widely used in medical organizations and are one of the factors of pathogenic microflora spreading. In this work, the possibility of using substances from the group of cationic surfactants to impart antimicrobial properties to textile materials was considered. Substances from different classes were used – tertiary amines, quaternary ammonium compounds, polymeric guanidine derivatives. The substances were applied from aqueous solutions using a laboratory analogue of a drying and a shirring machine. An acrylate binder with thermal initiation of polymerization was used to fix the active substances to the tissues. The content of the active substances in the tissues after application was determined by high-performance liquid chromatography. Antimicrobial activity of the obtained materials was checked by the agar plate method and the area of the growth retardation zone was estimated. Tissues containing N,N-bis(3-aminopropyl)dodecylamine showed the highest activity, tissues with poly (2-hydroxypropyl dimethylammonium) chloride the lowest. Keywords: antimicrobial materials, antimicrobial textile, HAI, cationic surfactants.
- 1 September 2020
- Published by National Organization of Disinfectionists in Disinfection affairs
- No. 3
Antimicrobial textile finishes: A brief review
Dezinfektsionnoe delo, Disinfection affairs
- 1 September 2020
- Published by National Organization of Disinfectionists in Disinfection affairs
- No. 3
Antimicrobial textile finishes: A brief review
Dezinfektsionnoe delo, Disinfection affairs