Danuta Król
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Danuta Król has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Sławomir Poskrobko
Faculty of Civil Engineering and Environmental Sciences, Białystok University of Technology, 15-351 Białystok, Poland
7 shared publications - Przemysław Motyl
Faculty of Mechanical Engineering, Radom University, Stasieckiego 54, 26-600 Radom, Poland
6 shared publications Sławomir Poskrobko
Białystok University of Technology, Białystok, Poland
4 shared publications- Grzegorz Gałko
Institute of Energy and Fuel Processing Technology, Zamkowa 1, 41-803 Zabrze, Poland
2 shared publications - Joanna Piotrowska-Woroniak
HVAC Department, Bialystok University of Technology, Wiejska 45E, 15-351 Bialystok, Poland
1 shared publication Józef Gościk
Technical University of Białystok, Wiejska 45C, 15–351 Białystok, Poland
1 shared publication
Latest Publications
- Open Access
Graph Neural Operator-Based Surrogate Modelling of Multi-Field CFD Results in Biomass Boiler
Computational fluid dynamics provides detailed spatial distributions of physical fields in biomass boiler combustion, but the computational cost of each simulation limits its application in parametric studies and near-real-time workflows. This work investigates whether a Graph Neural Operator (GNO) can serve as a fast surrogate model that maps boiler operating parameters to six coupled CFD field distributions simultaneously. The reference case is a 10 kW wood-pellet boiler with internal flue gas recirculation (FGR), described and experimentally validated in an earlier publication by the authors. CFD data were collected on the symmetry plane of the combustion chamber for 80 operating points defined by the thermal load ratio (P/P0) and the excess air ratio λ. A GNO surrogate was trained on 64 cases to predict temperature, velocity magnitude, static pressure, and mole fractions of CO, O2, and CO2 at each node of an unstructured spatial graph. On a held-out validation set of 16 operating cases, the model achieved R2 values of 0.988 for temperature, 0.919 for velocity magnitude, 0.982 for pressure, 0.999 for CO, 0.992 for O2, and 0.985 for CO2. After training, each prediction is generated in a single forward pass, providing a computationally efficient approximation compared to the full CFD solver. A dedicated generalisation study on independent off-grid CFD cases confirmed that the surrogate interpolates within the parameter domain with essentially no loss of accuracy and degrades only moderately when extrapolated towards a higher thermal load and leaner mixtures. The results demonstrate that a baseline GNO surrogate can capture the spatial structure of coupled thermo-fluid and species fields in a realistic combustion geometry within the investigated parameter range and suggest applicability to digital-twin-oriented workflows where repeated parametric queries of boiler operation are required.
Open AccessGraph Neural Operator-Based Surrogate Modelling of Multi-Field CFD Results in Biomass Boiler
Computational fluid dynamics provides detailed spatial distributions of physical fields in biomass boiler combustion, but the computational cost of each simulation limits its application in parametric studies and near-real-time workflows. This work investigates whether a Graph Neural Operator (GNO) can serve as a fast surrogate model that maps boiler operating parameters to six coupled CFD field distributions simultaneously. The reference case is a 10 kW wood-pellet boiler with internal flue gas recirculation (FGR), described and experimentally validated in an earlier publication by the authors. CFD data were collected on the symmetry plane of the combustion chamber for 80 operating points defined by the thermal load ratio (P/P0) and the excess air ratio λ. A GNO surrogate was trained on 64 cases to predict temperature, velocity magnitude, static pressure, and mole fractions of CO, O2, and CO2 at each node of an unstructured spatial graph. On a held-out validation set of 16 operating cases, the model achieved R2 values of 0.988 for temperature, 0.919 for velocity magnitude, 0.982 for pressure, 0.999 for CO, 0.992 for O2, and 0.985 for CO2. After training, each prediction is generated in a single forward pass, providing a computationally efficient approximation compared to the full CFD solver. A dedicated generalisation study on independent off-grid CFD cases confirmed that the surrogate interpolates within the parameter domain with essentially no loss of accuracy and degrades only moderately when extrapolated towards a higher thermal load and leaner mixtures. The results demonstrate that a baseline GNO surrogate can capture the spatial structure of coupled thermo-fluid and species fields in a realistic combustion geometry within the investigated parameter range and suggest applicability to digital-twin-oriented workflows where repeated parametric queries of boiler operation are required.
- Open Access
Thermal Destruction of Waste and the Impact of the Presence of Cl and S in Waste on the Emissions of Cu, Ni, and Pb and Their Immobilisation in the Ash Residue
This study addresses the pressing environmental problem of the emissions of ecotoxic heavy metals from high-temperature waste combustion processes, including incineration and pyrolysis. Such emissions pose a serious threat to ecosystems and human health. This study investigated the behaviour of the heavy metals Cu, Ni, and Pb during the combustion of various waste materials such as plastic waste, pharmaceutical waste, and pesticide waste. To limit the release of heavy metals into the exhaust gas stream, various additives were used: divanadium pentoxide (V2O5), borax (Na2B4O7), and their mixtures with calcium oxide (CaO). Additionally, this study examined the impact of the content of chlorine heteroatoms (Cl) in burned waste materials on the emission levels of Cu, Ni, and Pb. The findings shed light on the mobility of ecotoxic heavy metals in high-temperature waste incineration processes (1273, 1373 K) and offer insight into strategies to improve their immobilisation in grate residues. At a temperature of 1273 K, V2O5 with CaO reduced Pb emissions by ~65% for plastic waste and by ~40% for pesticide.
Open AccessThermal Destruction of Waste and the Impact of the Presence of Cl and S in Waste on the Emissions of Cu, Ni, and Pb and Their Immobilisation in the Ash Residue
This study addresses the pressing environmental problem of the emissions of ecotoxic heavy metals from high-temperature waste combustion processes, including incineration and pyrolysis. Such emissions pose a serious threat to ecosystems and human health. This study investigated the behaviour of the heavy metals Cu, Ni, and Pb during the combustion of various waste materials such as plastic waste, pharmaceutical waste, and pesticide waste. To limit the release of heavy metals into the exhaust gas stream, various additives were used: divanadium pentoxide (V2O5), borax (Na2B4O7), and their mixtures with calcium oxide (CaO). Additionally, this study examined the impact of the content of chlorine heteroatoms (Cl) in burned waste materials on the emission levels of Cu, Ni, and Pb. The findings shed light on the mobility of ecotoxic heavy metals in high-temperature waste incineration processes (1273, 1373 K) and offer insight into strategies to improve their immobilisation in grate residues. At a temperature of 1273 K, V2O5 with CaO reduced Pb emissions by ~65% for plastic waste and by ~40% for pesticide.
- Open Access
Waste Incineration and Heavy Metal Emission—Laboratory Tests
The main sources of environmental pollution with heavy (ecotoxic) metals include industry, including utility and municipal power engineering, but also waste incineration plants. Fuel shortages and their constantly growing prices raise concerns that energy will be commonly obtained from waste outside of installations intended for this purpose (i.e., outside waste incineration plants). The greatest concern stems from the risk of burning waste in low-power boilers—domestic boilers. Waste incineration plants and utility power plants are equipped with flue gas cleaning installations (FGD), but low-power boilers are not. The exhaust gases are directly introduced into the atmosphere, which results in the introduction into the air of, inter alia, toxic heavy metals. Therefore, it is necessary to conduct activities aimed at retaining ecotoxic metals in the solid–slag residue. The paper presents the results of laboratory tests of the emission capacity of Cd, Cu, Zn bound in various chemical forms—nitrates (V), chlorides and sulphates (VI). The tests were carried out at 1073 K, 1173 K and 1273 K. It was found that the emissivity of metals increased with increasing temperature. This is innovative as there are no reports of experiments with pure forms of metal salts. The advantage of this type of research is the lack of influence from other factors, apart from temperature, on metal emissions. To check the possibility of reducing metal emissions, additives (bauxite, dolomite, V2O5) immobilized in a solid residue were tested. The mechanism of action of each of the additives to limit the mobility of metals was different. The use of V2O5 for this purpose is new. The additives kept the metals solid in the residue, but their effect was different for each of the metals. The effectiveness of the tested additives was checked in the same temperature conditions, burning waste such as: rubber, sewage sludge and SRF fuel from waste. The effect of the additives depended on the type of waste, type of metal and the furnace temperature. If the additive effectively retained metals, then their amounts in the ashes were higher by several to several dozen percent in relation to the amount in the ashes remaining after waste incineration without additives. The results of the experiment with waste are open to research on the influence of other factors (except temperature) on the emissivity of Cd, Cu, Zn and the possibility of its reduction. The next step will be to verify the effects of laboratory tests in real conditions.
Open AccessWaste Incineration and Heavy Metal Emission—Laboratory Tests
The main sources of environmental pollution with heavy (ecotoxic) metals include industry, including utility and municipal power engineering, but also waste incineration plants. Fuel shortages and their constantly growing prices raise concerns that energy will be commonly obtained from waste outside of installations intended for this purpose (i.e., outside waste incineration plants). The greatest concern stems from the risk of burning waste in low-power boilers—domestic boilers. Waste incineration plants and utility power plants are equipped with flue gas cleaning installations (FGD), but low-power boilers are not. The exhaust gases are directly introduced into the atmosphere, which results in the introduction into the air of, inter alia, toxic heavy metals. Therefore, it is necessary to conduct activities aimed at retaining ecotoxic metals in the solid–slag residue. The paper presents the results of laboratory tests of the emission capacity of Cd, Cu, Zn bound in various chemical forms—nitrates (V), chlorides and sulphates (VI). The tests were carried out at 1073 K, 1173 K and 1273 K. It was found that the emissivity of metals increased with increasing temperature. This is innovative as there are no reports of experiments with pure forms of metal salts. The advantage of this type of research is the lack of influence from other factors, apart from temperature, on metal emissions. To check the possibility of reducing metal emissions, additives (bauxite, dolomite, V2O5) immobilized in a solid residue were tested. The mechanism of action of each of the additives to limit the mobility of metals was different. The use of V2O5 for this purpose is new. The additives kept the metals solid in the residue, but their effect was different for each of the metals. The effectiveness of the tested additives was checked in the same temperature conditions, burning waste such as: rubber, sewage sludge and SRF fuel from waste. The effect of the additives depended on the type of waste, type of metal and the furnace temperature. If the additive effectively retained metals, then their amounts in the ashes were higher by several to several dozen percent in relation to the amount in the ashes remaining after waste incineration without additives. The results of the experiment with waste are open to research on the influence of other factors (except temperature) on the emissivity of Cd, Cu, Zn and the possibility of its reduction. The next step will be to verify the effects of laboratory tests in real conditions.
- Open Access
Heat Reflective Thin-Film Polymer Insulation with Polymer Nanospheres—Determination of Thermal Conductivity Coefficient
In this paper, a method to determine the thermal conductivity coefficient λ in a 200 μm thick heat reflective paint layer, filled with polymer nanospheres with a Total Solar Reflectance (TSR) of 86.95%, is proposed and presented. For this purpose, a “hot box”-type (cube-shaped) test rig was built to carry out experimental tests to measure the temperature distribution on the surface of a double-layer wall containing the material under investigation. Together with the experimental studies, a CFD numerical model was prepared to understand the nature of flow and heat transfer inside the cube—the test chamber. Based on the proposed measurement and analysis method, the thermal conductivity coefficient of the heat reflective coating layer was λ = 0.0007941 W/m∙K.
Open AccessHeat Reflective Thin-Film Polymer Insulation with Polymer Nanospheres—Determination of Thermal Conductivity Coefficient
In this paper, a method to determine the thermal conductivity coefficient λ in a 200 μm thick heat reflective paint layer, filled with polymer nanospheres with a Total Solar Reflectance (TSR) of 86.95%, is proposed and presented. For this purpose, a “hot box”-type (cube-shaped) test rig was built to carry out experimental tests to measure the temperature distribution on the surface of a double-layer wall containing the material under investigation. Together with the experimental studies, a CFD numerical model was prepared to understand the nature of flow and heat transfer inside the cube—the test chamber. Based on the proposed measurement and analysis method, the thermal conductivity coefficient of the heat reflective coating layer was λ = 0.0007941 W/m∙K.
- Open Access
Chlorine Corrosion in a Low-Power Boiler Fired with Agricultural Biomass
The selection of appropriate heat-resistant materials which are at the same time resistant to atmospheres rich in chlorine and its compounds is one of the most important current construction problems in steel boiler elements when using biomass fuels of agricultural origin. In the research presented here, an area was identified in the furnace of a 10 kW boiler where there was a potential risk of chlorine corrosion. This zone was determined based on numerical analysis of the combustion process; it is the zone with the highest temperatures and where the gas atmosphere conducive to the formation of chlorine corrosion centers. Subsequently, tests were carried out in the process environment of the combustion chamber of a 10 kW boiler (the fuel was barley straw) by placing samples of eight construction materials in a numerically-designated zone. These included samples of steel (coal boiler St41K, heat-resistant H25T and H24JS, and heat-resistant valve 50H21G9N4) as well as intermetallic materials based on phases (FeAl, Fe3Al, NiAl, and Ni3Al). The samples remained in the atmosphere of the boiler furnace for 1152 h at a temperature of 750–900 °C. After this time, the surfaces of the samples were subjected to SEM microscopy and scanning analysis. The results showed that the St41K boiler steel was not suitable for operation under the assumed conditions, and that a thick layer of complex corrosion products was visible on its surface. The least amount of corrosion damage was observed for the samples of 50H21G9N4 steel and intermetallic materials.
Open AccessChlorine Corrosion in a Low-Power Boiler Fired with Agricultural Biomass
The selection of appropriate heat-resistant materials which are at the same time resistant to atmospheres rich in chlorine and its compounds is one of the most important current construction problems in steel boiler elements when using biomass fuels of agricultural origin. In the research presented here, an area was identified in the furnace of a 10 kW boiler where there was a potential risk of chlorine corrosion. This zone was determined based on numerical analysis of the combustion process; it is the zone with the highest temperatures and where the gas atmosphere conducive to the formation of chlorine corrosion centers. Subsequently, tests were carried out in the process environment of the combustion chamber of a 10 kW boiler (the fuel was barley straw) by placing samples of eight construction materials in a numerically-designated zone. These included samples of steel (coal boiler St41K, heat-resistant H25T and H24JS, and heat-resistant valve 50H21G9N4) as well as intermetallic materials based on phases (FeAl, Fe3Al, NiAl, and Ni3Al). The samples remained in the atmosphere of the boiler furnace for 1152 h at a temperature of 750–900 °C. After this time, the surfaces of the samples were subjected to SEM microscopy and scanning analysis. The results showed that the St41K boiler steel was not suitable for operation under the assumed conditions, and that a thick layer of complex corrosion products was visible on its surface. The least amount of corrosion damage was observed for the samples of 50H21G9N4 steel and intermetallic materials.
- Open Access
Numerical Modelling and Experimental Verification of the Low-Emission Biomass Combustion Process in a Domestic Boiler with Flue Gas Flow around the Combustion Chamber
The paper presents the results of numerical and experimental studies aimed at developing a new design of a 10 kW low-emission heating boiler fired with wood pellets. The boiler is to meet stringent requirements in terms of efficiency (η > 90%) and emissions per 10% O2: CO < 500 mg/Nm3, NOx ≤ 200 mg/Nm3, and dust ≤ 20 mg/Nm3; these emission restrictions are as prescribed in the applicable ECODESIGN Directive in the European Union countries. An innovative aspect of the boiler structure (not yet present in domestic boilers) is the circular flow of exhaust gases around the centrally placed combustion chamber. The use of such a solution ensures high-efficiency, low-emission combustion and meeting the requirements of ECODESIGN. The results of the numerical calculations were verified and confirmed experimentally, obtaining average emission values of the limited gases CO = 91 mg/Nm3, and NOx = 197 mg/Nm3. The temperature measured in the furnace is 450–500 °C and in the flue it was 157–197 °C. The determined boiler efficiency was 92%. Numerical calculations were made with the use of an advanced CFD (Computational Fluid Dynamics) workshop in the form of the Ansys programming and a computing environment with the dominant participation of the Fluent module. It was shown that the results obtained in both experiments are sufficiently convergent.
Open AccessNumerical Modelling and Experimental Verification of the Low-Emission Biomass Combustion Process in a Domestic Boiler with Flue Gas Flow around the Combustion Chamber
The paper presents the results of numerical and experimental studies aimed at developing a new design of a 10 kW low-emission heating boiler fired with wood pellets. The boiler is to meet stringent requirements in terms of efficiency (η > 90%) and emissions per 10% O2: CO < 500 mg/Nm3, NOx ≤ 200 mg/Nm3, and dust ≤ 20 mg/Nm3; these emission restrictions are as prescribed in the applicable ECODESIGN Directive in the European Union countries. An innovative aspect of the boiler structure (not yet present in domestic boilers) is the circular flow of exhaust gases around the centrally placed combustion chamber. The use of such a solution ensures high-efficiency, low-emission combustion and meeting the requirements of ECODESIGN. The results of the numerical calculations were verified and confirmed experimentally, obtaining average emission values of the limited gases CO = 91 mg/Nm3, and NOx = 197 mg/Nm3. The temperature measured in the furnace is 450–500 °C and in the flue it was 157–197 °C. The determined boiler efficiency was 92%. Numerical calculations were made with the use of an advanced CFD (Computational Fluid Dynamics) workshop in the form of the Ansys programming and a computing environment with the dominant participation of the Fluent module. It was shown that the results obtained in both experiments are sufficiently convergent.
- Open Access
- 14 December 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (12) , 14293-14298
Experimental research of oily sawdust air gasification
This article shows oily sawdust gasification research on countercurrent installation. Experimental research was on a laboratory scale. The main purpose of the experiment was combustible gas production with higher CH4 concentration. Gas concentrations like CO, CO2, CH4, H2, and CnHm determine syngas composition. The technological parameter’s value defines experimental conditions. Value of this was fuel to air ratio. With fuel to air ratio change, syngas composition was a differential phenomenon where it depended on the process parameters like temperature. Additionally, evaluation of methane formation from CO, H2, and CO2 was done. Methanization coefficients were based on CO and CO2 hydrogenation reactions. Component’s activity was in analogs way to syngas components changed.
- 14 December 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (12) , 14293-14298
Open AccessExperimental research of oily sawdust air gasification
This article shows oily sawdust gasification research on countercurrent installation. Experimental research was on a laboratory scale. The main purpose of the experiment was combustible gas production with higher CH4 concentration. Gas concentrations like CO, CO2, CH4, H2, and CnHm determine syngas composition. The technological parameter’s value defines experimental conditions. Value of this was fuel to air ratio. With fuel to air ratio change, syngas composition was a differential phenomenon where it depended on the process parameters like temperature. Additionally, evaluation of methane formation from CO, H2, and CO2 was done. Methanization coefficients were based on CO and CO2 hydrogenation reactions. Component’s activity was in analogs way to syngas components changed.
- Open Access
- 3 July 2019
- Published by MDPI AG in Proceedings
- Vol. 16 (1) , 33
Experimental Research on the Air Gasification of Oily Sawdust
In this article were present experimental results of the air gasification of oily sawdust. In a laboratory-scale countercurrent gas generator, gas composition measurements were made. We evaluated the fuel properties of the selected material with variable technological parameters (i.e., fuel to air ratio). Additionally, we evaluated the methanization coefficients and the dependence of their value on fuel and gasification agent content delivered to the chamber of the reaction.
- 3 July 2019
- Published by MDPI AG in Proceedings
- Vol. 16 (1) , 33
Open AccessExperimental Research on the Air Gasification of Oily Sawdust
In this article were present experimental results of the air gasification of oily sawdust. In a laboratory-scale countercurrent gas generator, gas composition measurements were made. We evaluated the fuel properties of the selected material with variable technological parameters (i.e., fuel to air ratio). Additionally, we evaluated the methanization coefficients and the dependence of their value on fuel and gasification agent content delivered to the chamber of the reaction.
- Open Access
- 28 June 2019
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 213, 02045
The influence of the conversion medium stream on the gasification process of olive pits
The paper presents the results of research on gasification of olive pits and production of a generator gas with calorific value enabling its combustion in microturbines. Gasification was carried out in a laboratory gasification reactor, where the converting factor was air. The influence of the flow rate of its stream on the composition of the generator gas was investigated. The research involved searching for optimal process conditions for gasification of this biomass, to obtain a generator gas with an increased CH4 content (methane is the most calorific component).The air flow in subsequent tests was 0.5m3/h, 0.85m3 /h, 1.1m3/h,. 1.4m3/h 1.7m3/h. The quantitative composition of the generated generator gases differed. These conditions were obtained with an air flow of 1.4m3/h, in a tubular reactor, at the bed temperature T3= 456–462oC. A gas was obtained, with a calorific value of 9.2MJ/m3, characteristic for the following gas composition: H2=3.88%, CO=18.52%, CO2=6.27%, CH4=16.02%, O2=1.28%.
- 28 June 2019
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 213, 02045
Open AccessThe influence of the conversion medium stream on the gasification process of olive pits
The paper presents the results of research on gasification of olive pits and production of a generator gas with calorific value enabling its combustion in microturbines. Gasification was carried out in a laboratory gasification reactor, where the converting factor was air. The influence of the flow rate of its stream on the composition of the generator gas was investigated. The research involved searching for optimal process conditions for gasification of this biomass, to obtain a generator gas with an increased CH4 content (methane is the most calorific component).The air flow in subsequent tests was 0.5m3/h, 0.85m3 /h, 1.1m3/h,. 1.4m3/h 1.7m3/h. The quantitative composition of the generated generator gases differed. These conditions were obtained with an air flow of 1.4m3/h, in a tubular reactor, at the bed temperature T3= 456–462oC. A gas was obtained, with a calorific value of 9.2MJ/m3, characteristic for the following gas composition: H2=3.88%, CO=18.52%, CO2=6.27%, CH4=16.02%, O2=1.28%.
- Open Access
- 28 June 2019
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 213, 02046
Transformations, threats and the bond of chlorine in the processes of burning the wastes
The aim of the study was to present the possibility of reducing the emission of HCl to the atmosphere and the possibility of limiting the formation of PCDD/F in the technologies of incineration of waste fuels and incineration of animal waste. Waste fuel and animal biomass were burned in a two-stage system i.e.: Io-gasification and IIo-combustion of gas products of gasification. As part of the implementation, the reduction of HCl emissions to air was investigated when Ca(OH)2 was added as an additive to the fuel from waste. Ca(OH)2 bonded HCl releasing into the gas space in the combustion process. HCl binding in the combustion chamber not only limited its emission to the atmosphere. Its elimination also limited the possibility of creating PCDD/F. In case of animal waste, HCl was captured with CaO produced from the decomposition of bone material (hydroxyapatite). The efficiency of this process was low. It was thus necessary to remove it in the built-in exhaust purification plant.
- 28 June 2019
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 213, 02046
Open AccessTransformations, threats and the bond of chlorine in the processes of burning the wastes
The aim of the study was to present the possibility of reducing the emission of HCl to the atmosphere and the possibility of limiting the formation of PCDD/F in the technologies of incineration of waste fuels and incineration of animal waste. Waste fuel and animal biomass were burned in a two-stage system i.e.: Io-gasification and IIo-combustion of gas products of gasification. As part of the implementation, the reduction of HCl emissions to air was investigated when Ca(OH)2 was added as an additive to the fuel from waste. Ca(OH)2 bonded HCl releasing into the gas space in the combustion process. HCl binding in the combustion chamber not only limited its emission to the atmosphere. Its elimination also limited the possibility of creating PCDD/F. In case of animal waste, HCl was captured with CaO produced from the decomposition of bone material (hydroxyapatite). The efficiency of this process was low. It was thus necessary to remove it in the built-in exhaust purification plant.