Daniela Ribeiro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniela Ribeiro has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- André Silva
Associate Laboratory of Energy, Transports and Aerospace (LAETA)/Aeronautics and Astronautics Research Center (AEROG), Universidade da Beira Interior, 6201-001 Covilhã, Portugal
17 shared publications - Jorge Barata
Aerospace Sciences Department, University of Beira Interior, Rua Marques Avila e Bolama, 6201-001 Covilha, Portugal
8 shared publications - Daniel Vasconcelos
AEROG, Aeronautics and Astronautics Research Center, LAETA, University of Beira Interior, Covilhã, Portugal
4 shared publications - Bernhard Weigand
Institute of Aerospace Thermodynamics (ITLR), University of Stuttgart, Stuttgart, Germany
3 shared publications - Miguel Rosa Oliveira Panão
University of Coimbra
3 shared publications - Patrick Foltyn
Institute of Aerospace Thermodynamics, University of Stuttgart, Stuttgart, Germany
3 shared publications
Latest Publications
- Open Access
- 30 March 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 164
Insights on bubble encapsulation after drop impact on thin liquid films
- 30 March 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 164
Open AccessInsights on bubble encapsulation after drop impact on thin liquid films
- Open Access
- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 033305
Criterion for bubble encapsulation on drop impact onto a liquid film
The phenomenon of bubble encapsulation results from droplet impact on a liquid film for specific impact conditions, but there is no established criterion for predicting its onset. Phenomenon visualization from two perspectives, the common lateral perspective and a bottom perspective, provided insights into the dynamics and formation mechanisms. Namely, the bottom shadowgraphs show capillary wavy patterns and perturbations imposed on the steady liquid film, which suggests a greater role of the liquid film in the onset of bubble encapsulation. Also, some considerations about the cavity development underneath the bubble limited by the solid wall allow concluding that the cavity shape is independent of the bubble encapsulation phenomenon. Additionally, using the bottom shadowgraphs, the crown closure time shows a systematic decrease in the dimensionless film thickness of , which will be subject of future work. Finally, while most drop impact correlations focus on using the droplets' characteristics and thermophysical properties, the experimental results point in a different direction. Considering correlations relating the Ohnesorge and Reynolds numbers, the new criterion for the onset of bubble encapsulation uses drop characteristics and properties in the Reynolds number, while the liquid film thickness and thermophysical properties are used in the Ohnesorge number because most of the crown material comes from the liquid film. Therefore, the criterion based on 100% occurrence of bubble encapsulation is not a threshold, but a range: , with . Other authors observed this phenomenon and despite being outside the validation range of this correlation, the values are close to their boundaries.- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 033305
Open AccessCriterion for bubble encapsulation on drop impact onto a liquid film
The phenomenon of bubble encapsulation results from droplet impact on a liquid film for specific impact conditions, but there is no established criterion for predicting its onset. Phenomenon visualization from two perspectives, the common lateral perspective and a bottom perspective, provided insights into the dynamics and formation mechanisms. Namely, the bottom shadowgraphs show capillary wavy patterns and perturbations imposed on the steady liquid film, which suggests a greater role of the liquid film in the onset of bubble encapsulation. Also, some considerations about the cavity development underneath the bubble limited by the solid wall allow concluding that the cavity shape is independent of the bubble encapsulation phenomenon. Additionally, using the bottom shadowgraphs, the crown closure time shows a systematic decrease in the dimensionless film thickness of , which will be subject of future work. Finally, while most drop impact correlations focus on using the droplets' characteristics and thermophysical properties, the experimental results point in a different direction. Considering correlations relating the Ohnesorge and Reynolds numbers, the new criterion for the onset of bubble encapsulation uses drop characteristics and properties in the Reynolds number, while the liquid film thickness and thermophysical properties are used in the Ohnesorge number because most of the crown material comes from the liquid film. Therefore, the criterion based on 100% occurrence of bubble encapsulation is not a threshold, but a range: , with . Other authors observed this phenomenon and despite being outside the validation range of this correlation, the values are close to their boundaries. - 1 December 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (12) , 123322
Influence of wetting behavior on the morphology of droplet impacts onto dry-patterned micro-structured surfaces
The influence of surface roughness, especially regularly patterned micro-structures on the physical outcomes of droplet impacts, is far from fully understood. In order to get a deeper insight into the physics of the impact phenomena, a systematic experimental study of the morphology on regularly patterned micro-structured surfaces has been carried out. The used structures with different dimensions were grooves and pillars with a square cross section. With the help of plasma activation and plasma polymerization processes, the surface wettability was modified independently from the surface structure and material. Two different test fluids were used, namely, distilled water and isopropanol, impacting with various impact energies onto the patterned surface samples. For a better characterization of the impact process, high-speed images from three different perspectives have been acquired synchronously. Due to the transparent surface material, the bottom perspective using a total internal reflection configuration was able to visualize air entrapment inside the surface structure. To the authors' knowledge, such images are not available in the literature, yet. The outcomes have been qualitatively investigated, summarized, and compared. A dependency of the outcomes on the impact energy, the surface wettability, and the structure dimensions could be clearly shown. In general, increasing impact energy will promote the tendency of splashing. However, roughness features cannot only trigger splashing, but can also inhibit it, for example, crown splashing. Moreover, reproducible arrangements of air entrapment inside the structure could be found, which was addressed by the authors as “cookie” and “button” due to their appearance.
- 1 December 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (12) , 123322
Influence of wetting behavior on the morphology of droplet impacts onto dry-patterned micro-structured surfaces
The influence of surface roughness, especially regularly patterned micro-structures on the physical outcomes of droplet impacts, is far from fully understood. In order to get a deeper insight into the physics of the impact phenomena, a systematic experimental study of the morphology on regularly patterned micro-structured surfaces has been carried out. The used structures with different dimensions were grooves and pillars with a square cross section. With the help of plasma activation and plasma polymerization processes, the surface wettability was modified independently from the surface structure and material. Two different test fluids were used, namely, distilled water and isopropanol, impacting with various impact energies onto the patterned surface samples. For a better characterization of the impact process, high-speed images from three different perspectives have been acquired synchronously. Due to the transparent surface material, the bottom perspective using a total internal reflection configuration was able to visualize air entrapment inside the surface structure. To the authors' knowledge, such images are not available in the literature, yet. The outcomes have been qualitatively investigated, summarized, and compared. A dependency of the outcomes on the impact energy, the surface wettability, and the structure dimensions could be clearly shown. In general, increasing impact energy will promote the tendency of splashing. However, roughness features cannot only trigger splashing, but can also inhibit it, for example, crown splashing. Moreover, reproducible arrangements of air entrapment inside the structure could be found, which was addressed by the authors as “cookie” and “button” due to their appearance.
- 1 October 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (10) , 105111
Measurement of the lamella thickness during droplet impact onto differently wettable smooth surfaces using an extension of the LASER Pattern Shift Method with naturally occurring patterns
This study shows that the LASER Pattern Shift Method (LPSM) is a powerful measurement technique for film thickness measurements. In this paper, the approach of the LPSM is extended, which is now able to measure the lamella thickness during droplet impacts on smooth surfaces using the naturally occurring air bubble shadows. With the help of this rather new measurement technique, the influence of different experimental parameters on the lamella thickness could be systematically assessed, e.g., the influence of impact velocity, liquid properties, and surface wettability. Upon comparing the obtained results to an analytical correlation in the literature, good agreement could be found for its validity range.
- 1 October 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (10) , 105111
Measurement of the lamella thickness during droplet impact onto differently wettable smooth surfaces using an extension of the LASER Pattern Shift Method with naturally occurring patterns
This study shows that the LASER Pattern Shift Method (LPSM) is a powerful measurement technique for film thickness measurements. In this paper, the approach of the LPSM is extended, which is now able to measure the lamella thickness during droplet impacts on smooth surfaces using the naturally occurring air bubble shadows. With the help of this rather new measurement technique, the influence of different experimental parameters on the lamella thickness could be systematically assessed, e.g., the influence of impact velocity, liquid properties, and surface wettability. Upon comparing the obtained results to an analytical correlation in the literature, good agreement could be found for its validity range.
- Open Access
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Collision Dynamics of a Single Droplet onto a Heated Dry Surface: Jet Fuel and HVO Mixtures
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Open AccessCollision Dynamics of a Single Droplet onto a Heated Dry Surface: Jet Fuel and HVO Mixtures
- Open Access
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
The influence of Wettability on the Droplet Impact onto Micro-Structured Surfaces
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Open AccessThe influence of Wettability on the Droplet Impact onto Micro-Structured Surfaces
- Open Access
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Effect of Surface Wettability on the Droplet Impact Morphologies on Dry Smooth Polycarbonate Surfaces
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Open AccessEffect of Surface Wettability on the Droplet Impact Morphologies on Dry Smooth Polycarbonate Surfaces
- Open Access
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Design and Fabrication of a Low Cost, Push Mode Piezoelectric Stream Droplet Generator with Interchangeable Nozzle
- 30 August 2021
- Published by Edinburgh University Library
- Vol. 1 (1)
Open AccessDesign and Fabrication of a Low Cost, Push Mode Piezoelectric Stream Droplet Generator with Interchangeable Nozzle
- 1 June 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (6) , 063305
Influence of wetting behavior on the morphology of droplet impacts onto dry smooth surfaces
The influence of wettability on the morphology of droplet impacts onto dry surfaces is often neglected in the literature, despite its significant effect on the resulting morphology. In this work, the role of wettability is investigated systematically by considering droplet impact processes on smooth dry surfaces of two different materials. The wetting behavior is varied not only by employing two different fluids, but most importantly by varying the surface properties by plasma activation and polymerization. Overall, this leads to four different wetting behaviors for each surface. The changes in impact morphology are visualized by means of a three-perspective experimental facility. In particular, the bottom view employs a total internal reflection-configuration for visualizing the exact droplet contact area and contact time. This enables us to characterize the main features of the different wetting behaviors. Overall, we found that surface wettability mainly influences the receding phase, resulting in higher receding rates with decreasing wettability but also the maximum spreading diameter.
- 1 June 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (6) , 063305
Influence of wetting behavior on the morphology of droplet impacts onto dry smooth surfaces
The influence of wettability on the morphology of droplet impacts onto dry surfaces is often neglected in the literature, despite its significant effect on the resulting morphology. In this work, the role of wettability is investigated systematically by considering droplet impact processes on smooth dry surfaces of two different materials. The wetting behavior is varied not only by employing two different fluids, but most importantly by varying the surface properties by plasma activation and polymerization. Overall, this leads to four different wetting behaviors for each surface. The changes in impact morphology are visualized by means of a three-perspective experimental facility. In particular, the bottom view employs a total internal reflection-configuration for visualizing the exact droplet contact area and contact time. This enables us to characterize the main features of the different wetting behaviors. Overall, we found that surface wettability mainly influences the receding phase, resulting in higher receding rates with decreasing wettability but also the maximum spreading diameter.