Gerald Müller
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gerald Müller has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Emanuele Quaranta
European Commission, Joint Research Centre (JRC)
3 shared publications Agustin Sánchez-Arcilla Conejo
1 shared publicationAlexander Gibby
Faculty of Engineering and the Environment, University of Southampton, Southampton, UK
1 shared publicationAlexander Goodwin
Faculty of Εngineering and Physical Sciences, University of Southampton, Southampton, UK
1 shared publication- Andrea Marzeddu
Maritime Engineering Laboratory, Universitat Politècnica de Catalunya—BarcelonaTech 2 , Carrer de Jordi Girona 1-3, Campus Nord, Edifici D1, Barcelona 08034, Spain
1 shared publication Branislav Mereš
Althandel Civic Association, Nová Baňa, Slovakia
1 shared publication
Latest Publications
- Open Access
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 16
WAVE INDUCED LOADS ON RECURVES ATOP A SEAWALL ON A SLOPED SEABED
The current work adds on previous research and presents large scale experimental results of wave induced forces on a recurve atop a seawall at the end of a sloped approaching bed. In addition to the experimental results a theoretical expression for predicting the violent wave induced loads is also reported.
- 1 September 2023
- Published by Coastal Engineering Research Council in Coastal Engineering Proceedings
- No. 37,p. 16
Open AccessWAVE INDUCED LOADS ON RECURVES ATOP A SEAWALL ON A SLOPED SEABED
The current work adds on previous research and presents large scale experimental results of wave induced forces on a recurve atop a seawall at the end of a sloped approaching bed. In addition to the experimental results a theoretical expression for predicting the violent wave induced loads is also reported.
- Open Access
- 4 July 2023
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 61 (4) , 431-436
Two simple theoretical models for teaching wave mechanics in coastal engineering
- 4 July 2023
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 61 (4) , 431-436
Open AccessTwo simple theoretical models for teaching wave mechanics in coastal engineering
- 16 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 237 (7) , 1577-1584
Assessment of the Newcomen engine’s development potential as heat engine for low temperature waste heat
There is a large but mostly unused energy resource available from low temperature waste heat with temperatures of 80–150°C. The lack of a cost-effective technology prevents the generation of power from this potential. Recently, the Condensing Engine, which employs the condensation of steam and the arising vacuum as the driving force, had been developed to address this problem. Its simplicity and the use of water as working fluid promises cost-effectiveness. In the context of this work, it was decided to investigate the Newcomen Engine to assess its potential. This engine is usually neglected because of is low efficiency, thought to be caused by the continuous cooling and re-heating of the cylinder. A thermodynamic model of the engine was developed. Surprisingly, the model indicated that 78% of the heat losses are caused by the re-heating of the injection water and only 22% by the cooling and re-heating of the cylinder. This finding allowed to conceptualise a new engine, the Internal Condensation Engine, where plastic material for the cylinder and the forced ejection of the water minimise losses. The engine would have a similar or better efficiency than competitive technologies whilst being simpler, and therefore more cost-effective.
- 16 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 237 (7) , 1577-1584
Assessment of the Newcomen engine’s development potential as heat engine for low temperature waste heat
There is a large but mostly unused energy resource available from low temperature waste heat with temperatures of 80–150°C. The lack of a cost-effective technology prevents the generation of power from this potential. Recently, the Condensing Engine, which employs the condensation of steam and the arising vacuum as the driving force, had been developed to address this problem. Its simplicity and the use of water as working fluid promises cost-effectiveness. In the context of this work, it was decided to investigate the Newcomen Engine to assess its potential. This engine is usually neglected because of is low efficiency, thought to be caused by the continuous cooling and re-heating of the cylinder. A thermodynamic model of the engine was developed. Surprisingly, the model indicated that 78% of the heat losses are caused by the re-heating of the injection water and only 22% by the cooling and re-heating of the cylinder. This finding allowed to conceptualise a new engine, the Internal Condensation Engine, where plastic material for the cylinder and the forced ejection of the water minimise losses. The engine would have a similar or better efficiency than competitive technologies whilst being simpler, and therefore more cost-effective.
- Open Access
- 5 January 2022
- Published by Taylor & Francis in Ish Journal of Hydraulic Engineering
- Vol. 29 (2) , 129-137
The impulse wheel as hydropower converter for irrigation systems
There is a significant hydropower potential in irrigation canals worldwide. Much of this potential exists as energy dissipating ramp-type fall structures. Hydropower could be employed to pump water for water saving irrigation, or to generate electricity. This hydropower is unused, since there are no cost-effective hydropower converters for the specific conditions in irrigation canals, i.e. head differences from 0.3 to 5 m and flow volumes ranging from 0.1 to 15 m3/s. At Southampton University, a simple undershot impulse-type waterwheel with 180° jet deflection was developed specifically for this application. Large scale tests, with a scaling ratio of 1:2.4, showed efficiencies of 53%, confirming predictions from theory. The model employed a novel roller-type power take-off which eliminates the requirement for a cost-intensive gearbox. The impulse wheel has considerable development potential, and could be a cost-effective solution for small hydropower sites at ramp structures.
- 5 January 2022
- Published by Taylor & Francis in Ish Journal of Hydraulic Engineering
- Vol. 29 (2) , 129-137
Open AccessThe impulse wheel as hydropower converter for irrigation systems
There is a significant hydropower potential in irrigation canals worldwide. Much of this potential exists as energy dissipating ramp-type fall structures. Hydropower could be employed to pump water for water saving irrigation, or to generate electricity. This hydropower is unused, since there are no cost-effective hydropower converters for the specific conditions in irrigation canals, i.e. head differences from 0.3 to 5 m and flow volumes ranging from 0.1 to 15 m3/s. At Southampton University, a simple undershot impulse-type waterwheel with 180° jet deflection was developed specifically for this application. Large scale tests, with a scaling ratio of 1:2.4, showed efficiencies of 53%, confirming predictions from theory. The model employed a novel roller-type power take-off which eliminates the requirement for a cost-intensive gearbox. The impulse wheel has considerable development potential, and could be a cost-effective solution for small hydropower sites at ramp structures.
- Open Access
- 10 December 2021
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 18 (24) , 13051
Noise Generation and Acoustic Impact of Free Surface Hydropower Machines: Focus on Water Wheels and Emerging Challenges
The noise generated by free surface hydropower machines, e.g., water wheels, has led to complaints and to restrictions in their operation in urban areas. This problem generally occurs when water wheels are not well designed and are installed without expertise. Despite the relevance of the problem, and the growing interest in the use of water wheels at existing low head barriers, the acoustic impact of water wheels has not yet been properly addressed by the scientific community. Therefore, in this manuscript, the importance of the problem and the related scientific challenges are discussed, supported by case studies and theoretical considerations. A literature review on the topic is carried out, although little information is available in the scientific domain. The aim of this work is to increase the awareness on this problem, in order to stimulate future research and to suggest useful guidelines for future water wheel projects, thereby increasing the water wheel potential and reducing noise disturbance for people.
- 10 December 2021
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 18 (24) , 13051
Open AccessNoise Generation and Acoustic Impact of Free Surface Hydropower Machines: Focus on Water Wheels and Emerging Challenges
The noise generated by free surface hydropower machines, e.g., water wheels, has led to complaints and to restrictions in their operation in urban areas. This problem generally occurs when water wheels are not well designed and are installed without expertise. Despite the relevance of the problem, and the growing interest in the use of water wheels at existing low head barriers, the acoustic impact of water wheels has not yet been properly addressed by the scientific community. Therefore, in this manuscript, the importance of the problem and the related scientific challenges are discussed, supported by case studies and theoretical considerations. A literature review on the topic is carried out, although little information is available in the scientific domain. The aim of this work is to increase the awareness on this problem, in order to stimulate future research and to suggest useful guidelines for future water wheel projects, thereby increasing the water wheel potential and reducing noise disturbance for people.
- 12 November 2019
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 58 (5) , 845-849
Optimization of undershot water wheels in very low and variable flow rate applications
Undershot water wheels are hydropower converters for head differences between 0.5 and 1.5 m. The Zuppinger and Sagebien types are the most used and efficient. Optimal rotational speeds depend on the head difference and on the flow rate: hence, in variable flow rate applications, the variable rotational speed is needed to optimize the performance, requiring expensive power take-off systems. In light of this, the use of adjustable inflow weirs was tested on Zuppinger and Sagebien wheels. Different flow rates were tested, each one with an inflow weir height chosen to maintain the upstream water level constant through the tests. The first aim was to increase the power at very low flows. The second aim was to maintain the range of optimal rotational speeds as narrow as possible over the flow rate range. The maximum acceptable weir height ranged between 1:15 and 1:10 of the wheel’s radius.
- 12 November 2019
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 58 (5) , 845-849
Optimization of undershot water wheels in very low and variable flow rate applications
Undershot water wheels are hydropower converters for head differences between 0.5 and 1.5 m. The Zuppinger and Sagebien types are the most used and efficient. Optimal rotational speeds depend on the head difference and on the flow rate: hence, in variable flow rate applications, the variable rotational speed is needed to optimize the performance, requiring expensive power take-off systems. In light of this, the use of adjustable inflow weirs was tested on Zuppinger and Sagebien wheels. Different flow rates were tested, each one with an inflow weir height chosen to maintain the upstream water level constant through the tests. The first aim was to increase the power at very low flows. The second aim was to maintain the range of optimal rotational speeds as narrow as possible over the flow rate range. The maximum acceptable weir height ranged between 1:15 and 1:10 of the wheel’s radius.
- 24 May 2019
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 58 (3) , 541-547
Energy dissipation through entrained air compression in plunging jets
The energy dissipation in plunge pools is often related to air entrainment in the plunging jet. Recent experimental work showed that the void fractions below the impinging jet are significantly smaller than outside the jet impact. This was attributed to the compression of the entrained air bubbles. In this paper, the thermodynamics of air bubble compression is introduced as a novel energy dissipation mechanism in civil engineering hydraulics. For the analysis of reported experimental data, isothermal conditions were applied as a lower bound approximation. It was found that the energy dissipation rates range from 2.7–9.7% for a jet velocity of 10 m s−2 and void fractions of 0.11 and 0.31, to 15.9–36.0% for a jet velocity of 24.5 m s−1 and void fractions of 0.35–0.55. The results may explain the difference between energy dissipation rates in plunge pools at model and full scale.
- 24 May 2019
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 58 (3) , 541-547
Energy dissipation through entrained air compression in plunging jets
The energy dissipation in plunge pools is often related to air entrainment in the plunging jet. Recent experimental work showed that the void fractions below the impinging jet are significantly smaller than outside the jet impact. This was attributed to the compression of the entrained air bubbles. In this paper, the thermodynamics of air bubble compression is introduced as a novel energy dissipation mechanism in civil engineering hydraulics. For the analysis of reported experimental data, isothermal conditions were applied as a lower bound approximation. It was found that the energy dissipation rates range from 2.7–9.7% for a jet velocity of 10 m s−2 and void fractions of 0.11 and 0.31, to 15.9–36.0% for a jet velocity of 24.5 m s−1 and void fractions of 0.35–0.55. The results may explain the difference between energy dissipation rates in plunge pools at model and full scale.
- 25 January 2018
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 56 (4) , 526-536
Sagebien and Zuppinger water wheels for very low head hydropower applications
In rivers and at old mill sites there is a substantial amount of very low-head hydropower with head differences from 0.3 to 1.5 m. Much of this potential is unused since in these conditions modern hydropower technology is not cost effective. In the mid-nineteenth century, the Sagebien and Zuppinger wheels were developed for such situations. Recent model tests showed the Zuppinger wheel has a maximum efficiency of 85%. No such data are however available for the Sagebien wheel. At Southampton University, 1:10 scale model tests with Sagebien and Zuppinger wheels were conducted. Both wheels had maximum efficiency of 84%. The Sagebien wheel’s performance curve was less affected by the flow rate. Contrary to the Zuppinger wheel, the Sagebien wheel’s geometry avoids noise generation at the upstream blade entry. The results indicate that the Sagebien wheel is an attractive, although so far underestimated, hydropower converter for very low-head situations.
- 25 January 2018
- Published by Taylor & Francis in Journal of Hydraulic Research
- Vol. 56 (4) , 526-536
Sagebien and Zuppinger water wheels for very low head hydropower applications
In rivers and at old mill sites there is a substantial amount of very low-head hydropower with head differences from 0.3 to 1.5 m. Much of this potential is unused since in these conditions modern hydropower technology is not cost effective. In the mid-nineteenth century, the Sagebien and Zuppinger wheels were developed for such situations. Recent model tests showed the Zuppinger wheel has a maximum efficiency of 85%. No such data are however available for the Sagebien wheel. At Southampton University, 1:10 scale model tests with Sagebien and Zuppinger wheels were conducted. Both wheels had maximum efficiency of 84%. The Sagebien wheel’s performance curve was less affected by the flow rate. Contrary to the Zuppinger wheel, the Sagebien wheel’s geometry avoids noise generation at the upstream blade entry. The results indicate that the Sagebien wheel is an attractive, although so far underestimated, hydropower converter for very low-head situations.
- 19 October 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 232 (4) , 437-448
The condensing engine: A heat engine for operating temperatures of 100 ℃ and below
The cost-effective utilisation of low-grade thermal energy with temperatures below 150 ℃ for electricity generation still constitutes an engineering challenge. Existing technology, e.g. the organic Rankine cycle machines, are complex and only economical for larger power outputs. At Southampton University, the steam condensation cycle for a working temperature of 100 ℃ was analysed theoretically. The cycle uses water as working fluid, which has the advantages of being cheap, readily available, non-toxic, non-inflammable and non-corrosive, and works at and below atmospheric pressure, so that leakage and sealing are not problematic. Steam expansion will increase the theoretical efficiency of the cycle from 6.4% (no expansion) to 17.8% (expansion ratio 1:8). In this article, the theoretical development of the cycle is presented. A 40 Watt experimental engine was built and tested. Efficiencies ranged from 0.02 (no expansion) to 0.055 (expansion ratio 1:4). The difference between theoretical and experimental efficiencies was attributed to significant pressure loss in valves, and to difficulties with heat rejection. It was concluded that the condensing engine has potential for further development.
- 19 October 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 232 (4) , 437-448
The condensing engine: A heat engine for operating temperatures of 100 ℃ and below
The cost-effective utilisation of low-grade thermal energy with temperatures below 150 ℃ for electricity generation still constitutes an engineering challenge. Existing technology, e.g. the organic Rankine cycle machines, are complex and only economical for larger power outputs. At Southampton University, the steam condensation cycle for a working temperature of 100 ℃ was analysed theoretically. The cycle uses water as working fluid, which has the advantages of being cheap, readily available, non-toxic, non-inflammable and non-corrosive, and works at and below atmospheric pressure, so that leakage and sealing are not problematic. Steam expansion will increase the theoretical efficiency of the cycle from 6.4% (no expansion) to 17.8% (expansion ratio 1:8). In this article, the theoretical development of the cycle is presented. A 40 Watt experimental engine was built and tested. Efficiencies ranged from 0.02 (no expansion) to 0.055 (expansion ratio 1:4). The difference between theoretical and experimental efficiencies was attributed to significant pressure loss in valves, and to difficulties with heat rejection. It was concluded that the condensing engine has potential for further development.
- Open Access
- 1 June 2016
- Published by Elsevier in Coastal Engineering
- Vol. 112, 44-56
Measuring wave impact induced pressures with a pressure mapping system
- 1 June 2016
- Published by Elsevier in Coastal Engineering
- Vol. 112, 44-56
Open AccessMeasuring wave impact induced pressures with a pressure mapping system