Qing Mao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qing Mao has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
Sen Wang
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin 300072, China
1 shared publication- Sen Wang
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, 300072 Tianjin, China
1 shared publication Shugui Liu
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin 300072, China
1 shared publication- Shugui Liu
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin 300072, China
1 shared publication
Latest Publications
- Open Access
- 11 November 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 206, 03023
Surface Fitting for non-Grid Data from in-Situ Measuring Systems of Aero-engine Blade
High machining accuracy of aero-engine blade largely determines the carrying capacity, endurance, acceleration and the dynamic performance of the aero-engine, so a reliable machining error inspection and evaluation technique is imperative. In order to give a reliable error evaluation, the non- uniform rational B-spline (NURBS) technique is adopted to reconstruct the surface within a specified accuracy. Usually, data points measured from aero-engine blade are non-grid data in situ measuring systems. To overcome the difficulty of NURBS surface fitting from non-grid data, a new method based on data conversion is proposed, in which chord length parameterization and uniform parameter sampling are combined together to realize the data convertation, and subsequently hierarchical fitting strategy is applied to finish the NURBS surface reconstruction. The way proposed for data conversion is easy to realize, and by which gemetrical features of original measured data are also reserved well, which make the whole method outstanding in low time cost. Experimental results show that the method is fast, effective. The source code has been implemented in VC++, while the resulting pictures are constructed in Matlab with the obtained control points, knot vectors, and the orders.
- 11 November 2020
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 206, 03023
Open AccessSurface Fitting for non-Grid Data from in-Situ Measuring Systems of Aero-engine Blade
High machining accuracy of aero-engine blade largely determines the carrying capacity, endurance, acceleration and the dynamic performance of the aero-engine, so a reliable machining error inspection and evaluation technique is imperative. In order to give a reliable error evaluation, the non- uniform rational B-spline (NURBS) technique is adopted to reconstruct the surface within a specified accuracy. Usually, data points measured from aero-engine blade are non-grid data in situ measuring systems. To overcome the difficulty of NURBS surface fitting from non-grid data, a new method based on data conversion is proposed, in which chord length parameterization and uniform parameter sampling are combined together to realize the data convertation, and subsequently hierarchical fitting strategy is applied to finish the NURBS surface reconstruction. The way proposed for data conversion is easy to realize, and by which gemetrical features of original measured data are also reserved well, which make the whole method outstanding in low time cost. Experimental results show that the method is fast, effective. The source code has been implemented in VC++, while the resulting pictures are constructed in Matlab with the obtained control points, knot vectors, and the orders.
- Open Access
A CMM-Based Method of Control Point Position Calibration for Light Pen Coordinate Measuring System
A light pen coordinate measuring system (LPCMS) is a kind of vision-based portable coordinate measuring technique. It implements coordinate measurement by analyzing the image of a light pen, which has several control points and a probe. The relative positions of control points need to be determined before measurement and serve as the measuring basis in LPCMS. How to accurately calibrate the relative positions of control points is the most important issue in system calibration. In this paper, a new method of control point position calibration based on a traditional coordinate measuring machine (CMM) is proposed. A light pen is fastened to the measuring arm of a CMM and performs accurate translational movement driven by the CMM. A camera is used to capture the images of control points at different positions, and the corresponding readings of the CMM are recorded at the same time. By establishing a separate coordinate system for each control point, the relative positions of the control points can be transformed to the differences of a series of translation vectors. Experiments show that the calibration repeatability of control point positions can reach 10 μm and the standard deviation of measurement of the whole LPCMS can reach 30 μm. A CMM is used to generate accurate translation, which provides a high accuracy basis of calibration. Through certain mathematical treatment, tremendous data acquired by moving the light pen to tens of thousands of different positions can be processed in a simple way, which can reduce the influence of random error. Therefore, the proposed method provides a high-accuracy solution of control point position calibration for LPCMS.
Open AccessA CMM-Based Method of Control Point Position Calibration for Light Pen Coordinate Measuring System
A light pen coordinate measuring system (LPCMS) is a kind of vision-based portable coordinate measuring technique. It implements coordinate measurement by analyzing the image of a light pen, which has several control points and a probe. The relative positions of control points need to be determined before measurement and serve as the measuring basis in LPCMS. How to accurately calibrate the relative positions of control points is the most important issue in system calibration. In this paper, a new method of control point position calibration based on a traditional coordinate measuring machine (CMM) is proposed. A light pen is fastened to the measuring arm of a CMM and performs accurate translational movement driven by the CMM. A camera is used to capture the images of control points at different positions, and the corresponding readings of the CMM are recorded at the same time. By establishing a separate coordinate system for each control point, the relative positions of the control points can be transformed to the differences of a series of translation vectors. Experiments show that the calibration repeatability of control point positions can reach 10 μm and the standard deviation of measurement of the whole LPCMS can reach 30 μm. A CMM is used to generate accurate translation, which provides a high accuracy basis of calibration. Through certain mathematical treatment, tremendous data acquired by moving the light pen to tens of thousands of different positions can be processed in a simple way, which can reduce the influence of random error. Therefore, the proposed method provides a high-accuracy solution of control point position calibration for LPCMS.