Sergii Panchenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sergii Panchenko has a total of 110 co-authors. Here are the top co-authors by number of shared publications:
- Alyona Lovska
Український державний університет залізничного транспорту, Україна
23 shared publications - Vasyl Ravlyuk
Department of Wagon Engineering and Product Quality, Ukrainian State University of Railway Transport, Feuerbach Square 7, 61050 Kharkiv, Ukraine
11 shared publications - Glib Vatulia
O.M. Beketov National University of Urban Economy in Kharkiv
9 shared publications - Juraj Gerlici
Department of Transport and Handling Machines, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
9 shared publications - Oleksij Fomin
State University of Infrastructure and Technologies
5 shared publications - Владислав Вадимович Панченко
Український державний університет залізничного транспорту
5 shared publications
Latest Publications
- Open Access
- 29 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (141)) , 33-39
Determining the loading on the body of a covered wagon modernized for container transportation
This study investigates the process of loading the body of a covered hopper railroad car, modernized for container transportation. The task addressed is to improve the efficiency of container transportation by rail. To this end, it is proposed to use covered wagons taking into account the modernization of their structure. The modernization involves dismantling the roof and placing fitting stops on the floor for fastening containers. The study was conducted using a universal covered wagon, model 11-217, as an example. The strength of the covered wagon body was calculated when it is subjected to vertical loads from containers, as well as the simultaneous action of vertical and longitudinal loads. It was established that when the body of the covered wagon is subjected to vertical loads, the maximum stresses in its structure are 8.3% lower than the permissible ones. When vertical and longitudinal loads are simultaneously applied, the maximum stresses in the body are 4% lower than the permissible ones. The calculation results prove that the strength of the covered wagon body, taking into account the proposed modernization, is maintained. A feature of the proposed modernization is the fact that, if necessary, the design of the covered wagon body can be returned to its original state. The scope of practical application of the results is railroad transport. A condition for using the findings is the symmetrical placement of the fitting stops relative to the transverse axis of the covered wagon body, which is due to the need to ensure uniform loading of both car bogies. This study will contribute to increasing the efficiency of container transportation by rail and container transportation in general
- 29 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (141)) , 33-39
Open AccessDetermining the loading on the body of a covered wagon modernized for container transportation
This study investigates the process of loading the body of a covered hopper railroad car, modernized for container transportation. The task addressed is to improve the efficiency of container transportation by rail. To this end, it is proposed to use covered wagons taking into account the modernization of their structure. The modernization involves dismantling the roof and placing fitting stops on the floor for fastening containers. The study was conducted using a universal covered wagon, model 11-217, as an example. The strength of the covered wagon body was calculated when it is subjected to vertical loads from containers, as well as the simultaneous action of vertical and longitudinal loads. It was established that when the body of the covered wagon is subjected to vertical loads, the maximum stresses in its structure are 8.3% lower than the permissible ones. When vertical and longitudinal loads are simultaneously applied, the maximum stresses in the body are 4% lower than the permissible ones. The calculation results prove that the strength of the covered wagon body, taking into account the proposed modernization, is maintained. A feature of the proposed modernization is the fact that, if necessary, the design of the covered wagon body can be returned to its original state. The scope of practical application of the results is railroad transport. A condition for using the findings is the symmetrical placement of the fitting stops relative to the transverse axis of the covered wagon body, which is due to the need to ensure uniform loading of both car bogies. This study will contribute to increasing the efficiency of container transportation by rail and container transportation in general
- Open Access
- 29 May 2026
- Published by Ukrainian State University of Railway Transport in Інформаційно-керуючі системи на залізничному транспорті
- Vol. 31 (2) , 105-112
Efficiency Evaluation of a Code Division Multiple Access System Based on a Multilevel Functional Model of Performance Indicators
The article considers the problem of evaluating the efficiency of a code division multiple access system that uses ensembles of unequal-energy complex signals. The purpose of the work is to develop an efficiency evaluation procedure for a code division multiple access system based on a multilevel functional model of performance indicators with determination of the set of model levels sufficient for the stated task. The multilevel functional model is treated as a set of levels ordered by the degree of generalization of efficiency estimates. Each level is associated with functionals that determine the corresponding performance indicators. The model includes energy, structural, power-channel and system levels. The energy level is related to the energy composition of the signal ensemble, the structural level is related to mutual-correlation parameters of the signals, the power-channel level is related to the corresponding channel-level parameter, and the system level is related to the final estimate for the stated task. The full model keeps a sequential structure: the indicator of each upper level is determined through the indicator of the previous adjacent level and the parameters that enter the current level. This prevents the system-level indicator from being mixed with the reduced functional used for comparison of variants. The procedure uses functional reduction to determine which level functionals must take part in the reduced functional for a given finite set of compared variants. For each level under consideration, the procedure checks whether there is at least one pair of variants for which the value of the corresponding level functional differs. If all variants have the same value of a level functional, that level does not enter the reduced functional for the considered task. If at least one level satisfies the difference condition, the reduced functional is formed by the mapping that transforms the values of the sufficient level functionals into one numerical efficiency estimate for each variant. The obtained numerical estimates are then used to order the variants according to the selected type of task, minimization or maximization. The practical value of the result is that efficiency evaluation, synthesis or optimization of a code division multiple access system can be performed by the values of the reduced functional, while the full multilevel model remains sequential and the comparison uses only the set of levels that is sufficient for the stated task and the given set of variants.
- 29 May 2026
- Published by Ukrainian State University of Railway Transport in Інформаційно-керуючі системи на залізничному транспорті
- Vol. 31 (2) , 105-112
Open AccessEfficiency Evaluation of a Code Division Multiple Access System Based on a Multilevel Functional Model of Performance Indicators
The article considers the problem of evaluating the efficiency of a code division multiple access system that uses ensembles of unequal-energy complex signals. The purpose of the work is to develop an efficiency evaluation procedure for a code division multiple access system based on a multilevel functional model of performance indicators with determination of the set of model levels sufficient for the stated task. The multilevel functional model is treated as a set of levels ordered by the degree of generalization of efficiency estimates. Each level is associated with functionals that determine the corresponding performance indicators. The model includes energy, structural, power-channel and system levels. The energy level is related to the energy composition of the signal ensemble, the structural level is related to mutual-correlation parameters of the signals, the power-channel level is related to the corresponding channel-level parameter, and the system level is related to the final estimate for the stated task. The full model keeps a sequential structure: the indicator of each upper level is determined through the indicator of the previous adjacent level and the parameters that enter the current level. This prevents the system-level indicator from being mixed with the reduced functional used for comparison of variants. The procedure uses functional reduction to determine which level functionals must take part in the reduced functional for a given finite set of compared variants. For each level under consideration, the procedure checks whether there is at least one pair of variants for which the value of the corresponding level functional differs. If all variants have the same value of a level functional, that level does not enter the reduced functional for the considered task. If at least one level satisfies the difference condition, the reduced functional is formed by the mapping that transforms the values of the sufficient level functionals into one numerical efficiency estimate for each variant. The obtained numerical estimates are then used to order the variants according to the selected type of task, minimization or maximization. The practical value of the result is that efficiency evaluation, synthesis or optimization of a code division multiple access system can be performed by the values of the reduced functional, while the full multilevel model remains sequential and the comparison uses only the set of levels that is sufficient for the stated task and the given set of variants.
- Open Access
- 4 May 2026
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 215,p. 317-328
MODELING OF LUBRICATION TYPES OF PLUGGING HYDRAULIC UNITS OF DRIVE SYSTEMS AND INTERNAL COMBUSTION ENGINES OF MOBILE TECHNOLOGICAL MACHINES
The article proposes a methodology for modeling the types of lubrication of plunger pairs of volumetric hydraulic units - pumps and motors, high-pressure fuel pumps, which are the main units of drive systems or power supply of mobile technological machines. Modeling the types of lubrication is based on establishing the limiting viscosity of the working fluid, at which the transition from the limiting or elastohydrodynamic lubrication to the stable hydrodynamic lubrication of the plunger pair occurs. The criterion for the transition from one type of lubrication to another is the relative thickness of the lubricating film, which is defined as the ratio of the actual minimum film thickness to the sum of the average values of the deviations of the microprofile of the contacting surfaces from the center line.The resulting mathematical model has the form of a dependence for determining the limiting transient viscosity, which takes into account the geometric and kinematic parameters of the plunger pair, the force acting on the plunger from the fluid pressure in the hydraulic system, as well as the condition of transition from limiting to liquid lubrication with a set value of the relative thickness of the lubricating film at level 5. For the selected initial data for the axial plunger pump, numerical verification of the mathematical model was carried out. The dependence of the plunger speed at half a revolution of the pump shaft on the fluid injection stroke, as well as the limiting viscosity, depending on the plunger stroke and the shaft rotation frequency, at constant fluid pressure, was established.In order to provide an example of modeling the types of lubrication of the proposed hydraulic unit, the values of the limiting viscosity obtained in the calculations were compared with the actual values of the dynamic viscosity of three hydraulic fluids of viscosity classes according to ISO VG-15, VG-22 and VG-46 at a temperature of 60 °C. The result of such a comparison was an assessment of the type of lubrication of the plunger pair when using working fluids of low and high viscosity. These actions established the transition points from limiting to stable hydrodynamic lubrication for different fluids, thereby proving the operability of the resulting model.
- 4 May 2026
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 215,p. 317-328
Open AccessMODELING OF LUBRICATION TYPES OF PLUGGING HYDRAULIC UNITS OF DRIVE SYSTEMS AND INTERNAL COMBUSTION ENGINES OF MOBILE TECHNOLOGICAL MACHINES
The article proposes a methodology for modeling the types of lubrication of plunger pairs of volumetric hydraulic units - pumps and motors, high-pressure fuel pumps, which are the main units of drive systems or power supply of mobile technological machines. Modeling the types of lubrication is based on establishing the limiting viscosity of the working fluid, at which the transition from the limiting or elastohydrodynamic lubrication to the stable hydrodynamic lubrication of the plunger pair occurs. The criterion for the transition from one type of lubrication to another is the relative thickness of the lubricating film, which is defined as the ratio of the actual minimum film thickness to the sum of the average values of the deviations of the microprofile of the contacting surfaces from the center line.The resulting mathematical model has the form of a dependence for determining the limiting transient viscosity, which takes into account the geometric and kinematic parameters of the plunger pair, the force acting on the plunger from the fluid pressure in the hydraulic system, as well as the condition of transition from limiting to liquid lubrication with a set value of the relative thickness of the lubricating film at level 5. For the selected initial data for the axial plunger pump, numerical verification of the mathematical model was carried out. The dependence of the plunger speed at half a revolution of the pump shaft on the fluid injection stroke, as well as the limiting viscosity, depending on the plunger stroke and the shaft rotation frequency, at constant fluid pressure, was established.In order to provide an example of modeling the types of lubrication of the proposed hydraulic unit, the values of the limiting viscosity obtained in the calculations were compared with the actual values of the dynamic viscosity of three hydraulic fluids of viscosity classes according to ISO VG-15, VG-22 and VG-46 at a temperature of 60 °C. The result of such a comparison was an assessment of the type of lubrication of the plunger pair when using working fluids of low and high viscosity. These actions established the transition points from limiting to stable hydrodynamic lubrication for different fluids, thereby proving the operability of the resulting model.
- Open Access
- 30 April 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (140)) , 14-20
Identifying regularities in the strength indicators of a passenger railroad car body depending on the use of a C-shaped profile with perforation in the girdle beam
This study considers processes resulting in the occurrence and acceptance of loads by the body of a passenger railroad car with a girdle beam under operational conditions. The task addressed is to improve the strength indicators of the girdle beam in a passenger car. To improve the strength of the frame of a passenger car, it is proposed to introduce a C-shaped profile with perforation as a profile for the girdle beam. The mass of the girdle beam using the proposed profile will decrease by more than 20%. At the same time, the moment of resistance of the cross-section of the girdle beam will increase by almost 14%. To substantiate such an implementation, a calculation was performed for the strength of the body of a passenger car under the main modes of its loading during operation. It was established that the maximum stresses arising in the girdle beam under the most unfavorable loading scheme are lower than the permissible ones by 20.5%. Under other design loading conditions of the body, the strength of its structure is also maintained. As part of the study, a modal analysis of the passenger car body was conducted. The calculations showed that traffic safety from the point of view of modal analysis is observed. A feature of the proposed improvement of the passenger car body is that it does not complicate the maintenance and repair of the car using the existing base. The scope of practical use of the results is railroad transport. The condition for using the research results is compliance with periodic maintenance of the passenger car body during operation. The study reported here will contribute to compiling recommendations for the design of new passenger car structures with improved technical and economic indicators
- 30 April 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (140)) , 14-20
Open AccessIdentifying regularities in the strength indicators of a passenger railroad car body depending on the use of a C-shaped profile with perforation in the girdle beam
This study considers processes resulting in the occurrence and acceptance of loads by the body of a passenger railroad car with a girdle beam under operational conditions. The task addressed is to improve the strength indicators of the girdle beam in a passenger car. To improve the strength of the frame of a passenger car, it is proposed to introduce a C-shaped profile with perforation as a profile for the girdle beam. The mass of the girdle beam using the proposed profile will decrease by more than 20%. At the same time, the moment of resistance of the cross-section of the girdle beam will increase by almost 14%. To substantiate such an implementation, a calculation was performed for the strength of the body of a passenger car under the main modes of its loading during operation. It was established that the maximum stresses arising in the girdle beam under the most unfavorable loading scheme are lower than the permissible ones by 20.5%. Under other design loading conditions of the body, the strength of its structure is also maintained. As part of the study, a modal analysis of the passenger car body was conducted. The calculations showed that traffic safety from the point of view of modal analysis is observed. A feature of the proposed improvement of the passenger car body is that it does not complicate the maintenance and repair of the car using the existing base. The scope of practical use of the results is railroad transport. The condition for using the research results is compliance with periodic maintenance of the passenger car body during operation. The study reported here will contribute to compiling recommendations for the design of new passenger car structures with improved technical and economic indicators
- 28 March 2026
- Published by Lutsk National Technical University in COMPUTER-INTEGRATED TECHNOLOGIES: EDUCATION, SCIENCE, PRODUCTION
- No. 62,p. 337-345
Methodology of Equivalent Transformations of Unequal-Energy Complex Signal Ensembles in Code-Division Multiple Access Systems
The paper develops a methodology of equivalent transformations for ensembles of complex signals with unequal energies in code-division multiple access (CDMA) systems. The relevance of this study arises from the limited applicability of classical equal-energy ensemble models to the analysis of CDMA systems under conditions of user energy heterogeneity. The proposed approach is based on preserving the total ensemble energy and its correlation structure, while transferring the effect of non-uniform signal energy distribution into scalar equivalence parameters. Within this framework, structural and energy equivalent transformations are introduced, forming a dual pair of equivalent volumes that ensure a consistent reproduction of the level of multiple-access interference for unequal-energy ensembles. It is shown that the proposed equivalent volumes retain the physical meaning of well-known correlation-based performance criteria and enable the use of analytical relations derived for equal-energy models without modification. The results of experimental modelling confirm the validity of the equivalent transformations and the adequacy of interference reproduction for various scenarios of energy heterogeneity. The obtained results can be employed for the analysis, comparison, and optimisation of signal ensembles in CDMA systems under conditions of non-uniform user energy distribution
- 28 March 2026
- Published by Lutsk National Technical University in COMPUTER-INTEGRATED TECHNOLOGIES: EDUCATION, SCIENCE, PRODUCTION
- No. 62,p. 337-345
Methodology of Equivalent Transformations of Unequal-Energy Complex Signal Ensembles in Code-Division Multiple Access Systems
The paper develops a methodology of equivalent transformations for ensembles of complex signals with unequal energies in code-division multiple access (CDMA) systems. The relevance of this study arises from the limited applicability of classical equal-energy ensemble models to the analysis of CDMA systems under conditions of user energy heterogeneity. The proposed approach is based on preserving the total ensemble energy and its correlation structure, while transferring the effect of non-uniform signal energy distribution into scalar equivalence parameters. Within this framework, structural and energy equivalent transformations are introduced, forming a dual pair of equivalent volumes that ensure a consistent reproduction of the level of multiple-access interference for unequal-energy ensembles. It is shown that the proposed equivalent volumes retain the physical meaning of well-known correlation-based performance criteria and enable the use of analytical relations derived for equal-energy models without modification. The results of experimental modelling confirm the validity of the equivalent transformations and the adequacy of interference reproduction for various scenarios of energy heterogeneity. The obtained results can be employed for the analysis, comparison, and optimisation of signal ensembles in CDMA systems under conditions of non-uniform user energy distribution
- Open Access
- 31 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (138)) , 45-51
Scientific rationale for the use of perforation beams in the bearing structure of a modernized railroad flat wagon for container transportation
This study investigates processes related to the occurrence, acceptance, and redistribution of loads in the supporting structure of a railroad flat wagon. The task addressed is to improve the technical and economic indicators of the modernized flat wagon for container transportation by reducing its tare. To this end, the stress distribution fields in the modernized railroad flat wagon structure were determined. It was established that the main longitudinal beams of the frame have a strength reserve, which is due to the underutilization of railroad flat wagon bearing capacity. This leads to an excess sprung mass of its supporting structure. Therefore, it is proposed to introduce perforation in the walls of the main longitudinal beams of a railroad flat wagon. To substantiate this solution, the strength of the bearing structure of a railroad flat wagon was calculated. It was established that the maximum stresses in the bearing structure are 13.6% lower than the permissible ones. The design service life of a railroad flat wagon is at least 32 years. The biaxiality calculation of the bearing structure showed that its greatest values are reached in the middle parts of girdle beams. A special feature of the proposed solution is that it makes it possible to improve the technical and economic indicators of the modernized railroad flat wagon with minor capital investments. The scope of practical application of the results is railroad transport. A condition for practical use of the results is symmetrical loading of the bearing structure of a railroad flat wagon with cargo. The results of the research could contribute to improving the efficiency of container cargo transportation along international routes. In addition, the results might prove useful for designing and fabricating new structures of railroad flat wagons, as well as for modernizing existing ones
- 31 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (138)) , 45-51
Open AccessScientific rationale for the use of perforation beams in the bearing structure of a modernized railroad flat wagon for container transportation
This study investigates processes related to the occurrence, acceptance, and redistribution of loads in the supporting structure of a railroad flat wagon. The task addressed is to improve the technical and economic indicators of the modernized flat wagon for container transportation by reducing its tare. To this end, the stress distribution fields in the modernized railroad flat wagon structure were determined. It was established that the main longitudinal beams of the frame have a strength reserve, which is due to the underutilization of railroad flat wagon bearing capacity. This leads to an excess sprung mass of its supporting structure. Therefore, it is proposed to introduce perforation in the walls of the main longitudinal beams of a railroad flat wagon. To substantiate this solution, the strength of the bearing structure of a railroad flat wagon was calculated. It was established that the maximum stresses in the bearing structure are 13.6% lower than the permissible ones. The design service life of a railroad flat wagon is at least 32 years. The biaxiality calculation of the bearing structure showed that its greatest values are reached in the middle parts of girdle beams. A special feature of the proposed solution is that it makes it possible to improve the technical and economic indicators of the modernized railroad flat wagon with minor capital investments. The scope of practical application of the results is railroad transport. A condition for practical use of the results is symmetrical loading of the bearing structure of a railroad flat wagon with cargo. The results of the research could contribute to improving the efficiency of container cargo transportation along international routes. In addition, the results might prove useful for designing and fabricating new structures of railroad flat wagons, as well as for modernizing existing ones
- Open Access
- 26 December 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 214,p. 181-200
АНАЛІЗ ЕФЕКТИВНОСТІ ЕКСПЛУАТАЦІЇ СУЧАСНИХ СИСТЕМ КЕРУВАННЯ БЕЗКОЛЕКТОРНИМИ ТЯГОВИМИ ДВИГУНАМИ
Подальший розвиток тягового рухомого складу залізниць нині багато в чому пов’язаний із переважним використанням безколекторних тягових двигунів, насамперед асинхронних. Однак ефективність роботи безколекторних тягових приводів значною мірою залежить від системи керування, яка формує оптимальний розподіл струмів, забезпечує плавний розгін, надійне гальмування з рекуперацією і стабільність роботи в широкому діапазоні режимів. Водночас впровадження систем керування в безколекторних тягових приводах залізничного транспорту супроводжено низкою технічних та експлуатаційних проблем. Метою статті є проведення всебічного аналізу умов експлуатації та оцінювання енергоефективності сучасних систем керування безколекторними тяговими двигунами, які застосовують на тяговому рухомому складі, для визначення їхніх переваг, недоліків і перспективних напрямів вдосконалення, що дасть змогу сформулювати рекомендації щодо вибору оптимальних алгоритмів і технічних рішень для конкретних умов роботи тягового рухомого складу. Об’єктом дослідження є процеси керування безколекторними тяговими електродвигунами в електроприводах тягового рухомого складу. У роботі розглянуто основні типи безколекторних тягових машин (синхронні з постійними магнітами, асинхронні), сучасні алгоритми керування (векторне керування, пряма регуляція моменту, адаптивні та оптимізуючі підходи), а також апаратні рішення перетворювачів і систем діагностики.Проведено порівняльний аналіз втрат і показників ефективності за типових режимів руху (розгін, сталий рух, гальмування з рекуперацією) з урахуванням температурних і навантажувальних факторів. Пропонована методика включає моделювання в імітаційному комп’ютерному середовищі, побудову карт ефективності, а також експериментальну валідацію на стенді з інвертором і датчиками струму/напруги/температури. Очікуваним результатом роботи є рекомендації щодо оптимізації алгоритмів керування і конфігурацій привода для підвищення ефективності роботи тягових двигунів, а також набір критеріїв для вибору привода залежно від режиму експлуатації тягового рухомого складу. Практична цінність полягає в можливості використання результатів дослідження для проєктування та модернізації електродвигунів тягового рухомого складу, що дасть змогу підвищити надійність засобів транспорту.
- 26 December 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 214,p. 181-200
Open AccessАНАЛІЗ ЕФЕКТИВНОСТІ ЕКСПЛУАТАЦІЇ СУЧАСНИХ СИСТЕМ КЕРУВАННЯ БЕЗКОЛЕКТОРНИМИ ТЯГОВИМИ ДВИГУНАМИ
Подальший розвиток тягового рухомого складу залізниць нині багато в чому пов’язаний із переважним використанням безколекторних тягових двигунів, насамперед асинхронних. Однак ефективність роботи безколекторних тягових приводів значною мірою залежить від системи керування, яка формує оптимальний розподіл струмів, забезпечує плавний розгін, надійне гальмування з рекуперацією і стабільність роботи в широкому діапазоні режимів. Водночас впровадження систем керування в безколекторних тягових приводах залізничного транспорту супроводжено низкою технічних та експлуатаційних проблем. Метою статті є проведення всебічного аналізу умов експлуатації та оцінювання енергоефективності сучасних систем керування безколекторними тяговими двигунами, які застосовують на тяговому рухомому складі, для визначення їхніх переваг, недоліків і перспективних напрямів вдосконалення, що дасть змогу сформулювати рекомендації щодо вибору оптимальних алгоритмів і технічних рішень для конкретних умов роботи тягового рухомого складу. Об’єктом дослідження є процеси керування безколекторними тяговими електродвигунами в електроприводах тягового рухомого складу. У роботі розглянуто основні типи безколекторних тягових машин (синхронні з постійними магнітами, асинхронні), сучасні алгоритми керування (векторне керування, пряма регуляція моменту, адаптивні та оптимізуючі підходи), а також апаратні рішення перетворювачів і систем діагностики.Проведено порівняльний аналіз втрат і показників ефективності за типових режимів руху (розгін, сталий рух, гальмування з рекуперацією) з урахуванням температурних і навантажувальних факторів. Пропонована методика включає моделювання в імітаційному комп’ютерному середовищі, побудову карт ефективності, а також експериментальну валідацію на стенді з інвертором і датчиками струму/напруги/температури. Очікуваним результатом роботи є рекомендації щодо оптимізації алгоритмів керування і конфігурацій привода для підвищення ефективності роботи тягових двигунів, а також набір критеріїв для вибору привода залежно від режиму експлуатації тягового рухомого складу. Практична цінність полягає в можливості використання результатів дослідження для проєктування та модернізації електродвигунів тягового рухомого складу, що дасть змогу підвищити надійність засобів транспорту.
- Open Access
- 1 July 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 212,p. 100-109
ELECTROCORROSION OF CONCRETE AND REINFORCED CONCRETE: ANALYSIS OF IMPACT AND PROTECTION METHODS
The Ukrainian railway infrastructure, as a key economic link, is strategically important but constantly faces significant loads and aggressive environments. This makes it vulnerable to structural damage. One of the most serious threats to the durability of its concrete and reinforced concrete structures is electrocorrosion. This phenomenon is caused by "stray currents" and high voltage, which arise from incomplete insulation between the rails and the ground. These currents intensify the migration of chloride ions and Ca2+ cations, accelerating rebar corrosion and concrete degradation. The article systematically analyzes and summarizes current understandings of electrocorrosion, identifying key destruction mechanisms, influencing factors, and protection methods. It also outlines critical research gaps and practical implications for enhancing railway infrastructure durability. Studying the durability of concrete and reinforced concrete is critically important because, while processes like carbonation and chloride penetration are well-researched, electrocorrosion is a distinct and complex problem. The alkaline environment of concrete usually provides a passive layer on steel rebar, but the penetration of carbon dioxide and chloride ions destroys this protective layer.Stray currents are divided into direct current (DC) and alternating current (AC). DC stray currents, typical for subways, cause significant corrosion of buried metal pipelines and accelerate pitting corrosion of steel, even surpassing the effects of fatigue. AC stray currents, common in ACelectrified railways, lead to a reduction in the service life of structures, although they cause less overall corrosion. The mechanisms of corrosion due to AC stray currents are more complex, including the rectification model, the alkalization mechanism, and the autocatalytic mechanism.Stray currents significantly alter the physicochemical properties of concrete: they accelerate the diffusion of calcium ions, increase porosity, and weaken the concrete's ability to bind chloride ions, creating an accelerated corrosion cycle. Experimental studies have shown that an AC voltage of 40 V, in combination with water flow, causes the maximum loss of concrete strength and intensive dissolution of cement paste minerals.The practical significance of these studies lies in improving the classification of concretes by permeability and developing protective solutions. These solutions include steel and liquid glass screens with deep grounding, as well as replacing traditional rail fastenings on sleepers and ballastless bridge deck slabs with resilient fastenings that have increased electrical resistance.The Ukrainian railway infrastructure faces additional challenges: aging structures, consequences of military actions (damage to railway tracks and electrical infrastructure, which disrupts grounding and insulation), insufficient quality control of materials, and the lack of comprehensive monitoring systems.Conclusions emphasize that electrocorrosion is a complex problem requiring a comprehensive approach to monitoring, diagnostics, and the implementation of modern protection methods.Prospects for further work include developing integrated real-time monitoring systems, in-depth study of the long-term effects of low AC voltages, creating new corrosion-resistant materials, optimizing existing protection systems, and adapting advanced computational methods for predicting degradation processes.
- 1 July 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 212,p. 100-109
Open AccessELECTROCORROSION OF CONCRETE AND REINFORCED CONCRETE: ANALYSIS OF IMPACT AND PROTECTION METHODS
The Ukrainian railway infrastructure, as a key economic link, is strategically important but constantly faces significant loads and aggressive environments. This makes it vulnerable to structural damage. One of the most serious threats to the durability of its concrete and reinforced concrete structures is electrocorrosion. This phenomenon is caused by "stray currents" and high voltage, which arise from incomplete insulation between the rails and the ground. These currents intensify the migration of chloride ions and Ca2+ cations, accelerating rebar corrosion and concrete degradation. The article systematically analyzes and summarizes current understandings of electrocorrosion, identifying key destruction mechanisms, influencing factors, and protection methods. It also outlines critical research gaps and practical implications for enhancing railway infrastructure durability. Studying the durability of concrete and reinforced concrete is critically important because, while processes like carbonation and chloride penetration are well-researched, electrocorrosion is a distinct and complex problem. The alkaline environment of concrete usually provides a passive layer on steel rebar, but the penetration of carbon dioxide and chloride ions destroys this protective layer.Stray currents are divided into direct current (DC) and alternating current (AC). DC stray currents, typical for subways, cause significant corrosion of buried metal pipelines and accelerate pitting corrosion of steel, even surpassing the effects of fatigue. AC stray currents, common in ACelectrified railways, lead to a reduction in the service life of structures, although they cause less overall corrosion. The mechanisms of corrosion due to AC stray currents are more complex, including the rectification model, the alkalization mechanism, and the autocatalytic mechanism.Stray currents significantly alter the physicochemical properties of concrete: they accelerate the diffusion of calcium ions, increase porosity, and weaken the concrete's ability to bind chloride ions, creating an accelerated corrosion cycle. Experimental studies have shown that an AC voltage of 40 V, in combination with water flow, causes the maximum loss of concrete strength and intensive dissolution of cement paste minerals.The practical significance of these studies lies in improving the classification of concretes by permeability and developing protective solutions. These solutions include steel and liquid glass screens with deep grounding, as well as replacing traditional rail fastenings on sleepers and ballastless bridge deck slabs with resilient fastenings that have increased electrical resistance.The Ukrainian railway infrastructure faces additional challenges: aging structures, consequences of military actions (damage to railway tracks and electrical infrastructure, which disrupts grounding and insulation), insufficient quality control of materials, and the lack of comprehensive monitoring systems.Conclusions emphasize that electrocorrosion is a complex problem requiring a comprehensive approach to monitoring, diagnostics, and the implementation of modern protection methods.Prospects for further work include developing integrated real-time monitoring systems, in-depth study of the long-term effects of low AC voltages, creating new corrosion-resistant materials, optimizing existing protection systems, and adapting advanced computational methods for predicting degradation processes.
- Open Access
- 21 May 2025
- Published by Ukrainian State University of Science and Technologies in Science and Transport Progress
- No. 2(110),p. 119-127
Experimental Research of the Strength of an Open Wagon Hatch Cover During the Transportation of Containers in it
Purpose. The work is aimed at highlighting the peculiarities of experimental studies of the strength of a hatch cover of an open wagon loaded from a fitting stop for fastening containers. Methodology. In order to make it possible to use open wagons for container transportation, an experimental study of the hatch cover of an open wagon loaded from a fitting stop was conducted. Bench tests were conducted in the research laboratory of the “Center for Diagnostics of Transport Structures” at the Ukrainian State University of Railway Transport. The stresses that arise in the design of the hatch cover were determined using the method of electrical strain gage measurement. The installation of strain gauges was carried out according to the bridge scheme. The locations of the strain gauges on the hatch cover were determined based on the theoretically obtained stress fields that arise in the hatch cover. Before installing the strain gauges, they were calibrated. The load on the fitting stop was transmitted through a metal cup that imitated the container fitting. The maximum load transferred to the fitting stop is assumed to be 6 t (60 kN), which corresponds to the maximum loaded state of a container of standard size 1CC. The strain gauge readings were taken using a VNP-8 strain gauge station. Findings. During the research, the maximum stresses in the hatch cover were 345.4 MPa. The obtained stresses exceed the permissible ones, which allows us to conclude that it is impossible to use such a container fastening scheme in practice. The largest percentage of discrepancy between the results of computer modeling and experimental research on the strength of the hatch cover of an open wagon is about 10% and is recorded when the load on the fitting stop is 30 kN. Originality. A procedure for conducting an experimental study of the strength of the hatch cover of an open wagon under the load from the fitting stop for fastening containers is proposed. The dependence of the stresses in the hatch cover of the open wagon on the load it perceives through the fitting stop was obtained. Practical value. The conducted research will contribute to the creation of recommendations for adapting open wagons to container transportation and increasing the efficiency of container transportation.
- 21 May 2025
- Published by Ukrainian State University of Science and Technologies in Science and Transport Progress
- No. 2(110),p. 119-127
Open AccessExperimental Research of the Strength of an Open Wagon Hatch Cover During the Transportation of Containers in it
Purpose. The work is aimed at highlighting the peculiarities of experimental studies of the strength of a hatch cover of an open wagon loaded from a fitting stop for fastening containers. Methodology. In order to make it possible to use open wagons for container transportation, an experimental study of the hatch cover of an open wagon loaded from a fitting stop was conducted. Bench tests were conducted in the research laboratory of the “Center for Diagnostics of Transport Structures” at the Ukrainian State University of Railway Transport. The stresses that arise in the design of the hatch cover were determined using the method of electrical strain gage measurement. The installation of strain gauges was carried out according to the bridge scheme. The locations of the strain gauges on the hatch cover were determined based on the theoretically obtained stress fields that arise in the hatch cover. Before installing the strain gauges, they were calibrated. The load on the fitting stop was transmitted through a metal cup that imitated the container fitting. The maximum load transferred to the fitting stop is assumed to be 6 t (60 kN), which corresponds to the maximum loaded state of a container of standard size 1CC. The strain gauge readings were taken using a VNP-8 strain gauge station. Findings. During the research, the maximum stresses in the hatch cover were 345.4 MPa. The obtained stresses exceed the permissible ones, which allows us to conclude that it is impossible to use such a container fastening scheme in practice. The largest percentage of discrepancy between the results of computer modeling and experimental research on the strength of the hatch cover of an open wagon is about 10% and is recorded when the load on the fitting stop is 30 kN. Originality. A procedure for conducting an experimental study of the strength of the hatch cover of an open wagon under the load from the fitting stop for fastening containers is proposed. The dependence of the stresses in the hatch cover of the open wagon on the load it perceives through the fitting stop was obtained. Practical value. The conducted research will contribute to the creation of recommendations for adapting open wagons to container transportation and increasing the efficiency of container transportation.
- Open Access
- 1 April 2025
- Published by University of Zilina in Communications - Scientific letters of the University of Zilina
- Vol. 27 (2) , B109-B117
The Strength Calculation of the Modernized Brake Lever Transmission for a Wagon Bogie
Journal Communications - Scientific Letters of the University of ?ilina is now a well-established open-access scientific journal aimed primarily at the topics connected with the field of transport.
- 1 April 2025
- Published by University of Zilina in Communications - Scientific letters of the University of Zilina
- Vol. 27 (2) , B109-B117
Open AccessThe Strength Calculation of the Modernized Brake Lever Transmission for a Wagon Bogie
Journal Communications - Scientific Letters of the University of ?ilina is now a well-established open-access scientific journal aimed primarily at the topics connected with the field of transport.