Joo-Hee Kang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Joo-Hee Kang has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Jinyoung Park
Electricity Technology Team, Samsung Electronics Co., Ltd., Hwaseong-si, Republic of Korea
3 shared publications - Jiwon Park
Materials Data & Analysis Division, Korea Institute of Materials Science
3 shared publications - Sangbum Kim
Seoul Natl Univ, Dept Nucl Engn, Gwanak Ro 1, Seoul, South Korea
3 shared publications - Sun Bae Bang
Safety Research Department, Electrical Safety Research Institute, Wanju-gun, Republic of Korea
3 shared publications - Young Ho Ko
Department of Electrical Engineering, Jeonbuk National University, Jeonju-si, Republic of Korea
3 shared publications - Chang-Seok Oh
Korea Institute of Materials Science, 66 Sangnam-dong, Changwon 51508, Republic of Korea
2 shared publications
Latest Publications
- 22 August 2025
- Published by Elsevier in Acta Materialia
- Vol. 301
Microstructural analysis of interconnected δ-hydride structures in a zirconium alloy
- 22 August 2025
- Published by Elsevier in Acta Materialia
- Vol. 301
Microstructural analysis of interconnected δ-hydride structures in a zirconium alloy
- 18 December 2024
- Published by Elsevier in Acta Materialia
- Vol. 285
Activation of different twinning mechanisms and their contributions to mechanical behavior of a face-centered cubic Co-based high-entropy alloy
- 18 December 2024
- Published by Elsevier in Acta Materialia
- Vol. 285
Activation of different twinning mechanisms and their contributions to mechanical behavior of a face-centered cubic Co-based high-entropy alloy
- 19 June 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 600
The influence of solid solution hydrogen and precipitated hydride on the creep behavior of Zircaloy-4
- 19 June 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 600
The influence of solid solution hydrogen and precipitated hydride on the creep behavior of Zircaloy-4
- Open Access
- 5 June 2024
- Published by Elsevier in Acta Materialia
- Vol. 275
Reorientation-induced plasticity (RIP) in titanium alloys
- 5 June 2024
- Published by Elsevier in Acta Materialia
- Vol. 275
Open AccessReorientation-induced plasticity (RIP) in titanium alloys
- Open Access
- 29 May 2024
- Published by Elsevier in Journal of Materiomics
- Vol. 11 (3) , 100887
Poling-free relaxor-PbTiO3 single crystals
- 29 May 2024
- Published by Elsevier in Journal of Materiomics
- Vol. 11 (3) , 100887
Open AccessPoling-free relaxor-PbTiO3 single crystals
- Open Access
- 5 November 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 4088-4108
Micromechanical analysis of anisotropy and asymmetry in pure titanium using electron backscatter diffraction and crystal plasticity finite element modeling
- 5 November 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 4088-4108
Open AccessMicromechanical analysis of anisotropy and asymmetry in pure titanium using electron backscatter diffraction and crystal plasticity finite element modeling
- 12 October 2023
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 588
Microstructure and mechanical properties of hydride blisters formed on Zircaloy-4 claddings
- 12 October 2023
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 588
Microstructure and mechanical properties of hydride blisters formed on Zircaloy-4 claddings
- 23 March 2023
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 580
Suppressed hydride precipitation in the welding zone of a zirconium-based alloy cladding tube
- 23 March 2023
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 580
Suppressed hydride precipitation in the welding zone of a zirconium-based alloy cladding tube
- Open Access
Discrimination of Copper Molten Marks through a Fire Reproduction Experiment Using Microstructure Features
The copper molten marks at a fire site provide important clues for determining the causes of fire. Four factors have been presented to quantitatively discriminate copper molten marks, namely the fraction of (001) component perpendicular to the demarcation line, the grain aspect ratio, the fraction of Σ3 boundaries, and the fraction of maximum grain size. However, only laboratory-level results of these parameters have been presented, and their applicability in actual fires is yet to be verified. In this study, a fire reproduction experimental system was configured to generate molten marks similar to those in actual fire sites. The molten marks were measured by electron backscatter diffraction and applied to the four discriminant factors. The results obtained similar characteristics to those of the laboratory unit, confirming the applicability of the four discriminant factors. Discriminant equations and processes that can distinguish the primary and secondary arc beads were derived using the molten marks generated in the laboratory and reproduction experiments. Furthermore, a probabilistic discrimination method and classification model developed by machine learning were proposed. Therefore, the use of the discriminants in actual fires can improve the reliability of the statistics and prevent the recurrence of similar fires.
Open AccessDiscrimination of Copper Molten Marks through a Fire Reproduction Experiment Using Microstructure Features
The copper molten marks at a fire site provide important clues for determining the causes of fire. Four factors have been presented to quantitatively discriminate copper molten marks, namely the fraction of (001) component perpendicular to the demarcation line, the grain aspect ratio, the fraction of Σ3 boundaries, and the fraction of maximum grain size. However, only laboratory-level results of these parameters have been presented, and their applicability in actual fires is yet to be verified. In this study, a fire reproduction experimental system was configured to generate molten marks similar to those in actual fire sites. The molten marks were measured by electron backscatter diffraction and applied to the four discriminant factors. The results obtained similar characteristics to those of the laboratory unit, confirming the applicability of the four discriminant factors. Discriminant equations and processes that can distinguish the primary and secondary arc beads were derived using the molten marks generated in the laboratory and reproduction experiments. Furthermore, a probabilistic discrimination method and classification model developed by machine learning were proposed. Therefore, the use of the discriminants in actual fires can improve the reliability of the statistics and prevent the recurrence of similar fires.
- Open Access
Potential Method to Distinguish Copper Molten Marks Using Boundary and Grain Characteristics
The microstructure of molten marks changes according to ambient temperatures, when a short circuit occurs. Investigation of microstructural changes is important for understanding the properties of copper and examining the cause of a fire. In this study, the boundary characteristics and grain-size distribution of molten marks—primary-arc beads (PABs), which short-circuited at room temperature (25 °C), and secondary-arc beads (SABs), which short-circuited at high temperatures (600 °C, 900 °C)—were compared using electron backscatter diffraction. The distribution of Σ3 boundaries was compared, and it was found that SABs have a higher fraction of Σ3 boundaries than PABs. Moreover, it was confirmed that the ratio of maximum grain size (area) to the total area of the molten mark in SABs is larger than that in PABs. Thus, reliable discriminant factors were suggested, such as the fraction of Σ3 boundaries and normalized maximum grain size, which can distinguish PABs and SABs. The four discriminant factors, such as the (001)//LD, GAR, fraction of Σ3 boundaries, and fraction of maximum grain size to the total molten-mark area, were verified using the machine learning of t-SNE and Pearson correlation analyses.
Open AccessPotential Method to Distinguish Copper Molten Marks Using Boundary and Grain Characteristics
The microstructure of molten marks changes according to ambient temperatures, when a short circuit occurs. Investigation of microstructural changes is important for understanding the properties of copper and examining the cause of a fire. In this study, the boundary characteristics and grain-size distribution of molten marks—primary-arc beads (PABs), which short-circuited at room temperature (25 °C), and secondary-arc beads (SABs), which short-circuited at high temperatures (600 °C, 900 °C)—were compared using electron backscatter diffraction. The distribution of Σ3 boundaries was compared, and it was found that SABs have a higher fraction of Σ3 boundaries than PABs. Moreover, it was confirmed that the ratio of maximum grain size (area) to the total area of the molten mark in SABs is larger than that in PABs. Thus, reliable discriminant factors were suggested, such as the fraction of Σ3 boundaries and normalized maximum grain size, which can distinguish PABs and SABs. The four discriminant factors, such as the (001)//LD, GAR, fraction of Σ3 boundaries, and fraction of maximum grain size to the total molten-mark area, were verified using the machine learning of t-SNE and Pearson correlation analyses.