K. S. Nanjunda Rao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
K. S. Nanjunda Rao has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Richardson Lal
Associate Professor, Dept. of Civil Engineering, Indian Institute of Science, Bangalore 560012, India
3 shared publications - B. V. Venkatarama Reddy
Professor, Dept. of Civil Engineering, Indian Institute of Science, Bangalore 560012, India
2 shared publications - Byrasandra Venkataramanappa Venkatarama Reddy
Professor (Retd.), Department of Civil Engineering, Indian Institute of Science Bangalore, Bangalore, India
2 shared publications B. V. Venkatarama Reddy
Indian Institute of Science
1 shared publication- G. S. Pavan
Research Scholar, Dept. of Civil Engineering, Indian Institute of Science, Bangalore, Karnataka 560012, India
1 shared publication K. S. Gumaste
Indian Institute of Science
1 shared publication
Latest Publications
- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (2)
Characteristic Compressive Strength of Cement-Stabilized Rammed Earth
The standard codes of practice on the rammed-earth construction are limited. It is essential to ascertain the characteristic compressive strength of the cement-stabilized rammed earth (CSRE) for the structural design of CSRE walls. The test procedures for determining the characteristic compressive strength of CSRE are not available in the standard codes of practices. The specimen size and its slenderness can affect the compressive strength of CSRE elements. This paper deals with the relationships between the specimen’s aspect ratio and compressive strength for CSRE using two cement contents (7 and 10%) and two densities. Both cylindrical and wallette specimens having an aspect ratio varying between 2 and 5.81 were tested for compressive strength. The results show that there is hardly any reduction in compressive strength as the aspect ratio was increased from 2 to 5.81 (a reduction in compressive strength of 1 and 3–5% for specimens with density of and , respectively). The study clearly demonstrates that the characteristic compressive strength of CSRE can be obtained by testing cylindrical (150 mm diameter and 300 mm height) or prism specimens (150 mm square cross section and 300 mm height) without applying any correction factor. Furthermore, since the moisture content in the specimen has a significant influence on the compressive strength of CSRE, it is recommended to adopt the wet compressive strength for structural design.- 1 February 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (2)
Characteristic Compressive Strength of Cement-Stabilized Rammed Earth
The standard codes of practice on the rammed-earth construction are limited. It is essential to ascertain the characteristic compressive strength of the cement-stabilized rammed earth (CSRE) for the structural design of CSRE walls. The test procedures for determining the characteristic compressive strength of CSRE are not available in the standard codes of practices. The specimen size and its slenderness can affect the compressive strength of CSRE elements. This paper deals with the relationships between the specimen’s aspect ratio and compressive strength for CSRE using two cement contents (7 and 10%) and two densities. Both cylindrical and wallette specimens having an aspect ratio varying between 2 and 5.81 were tested for compressive strength. The results show that there is hardly any reduction in compressive strength as the aspect ratio was increased from 2 to 5.81 (a reduction in compressive strength of 1 and 3–5% for specimens with density of and , respectively). The study clearly demonstrates that the characteristic compressive strength of CSRE can be obtained by testing cylindrical (150 mm diameter and 300 mm height) or prism specimens (150 mm square cross section and 300 mm height) without applying any correction factor. Furthermore, since the moisture content in the specimen has a significant influence on the compressive strength of CSRE, it is recommended to adopt the wet compressive strength for structural design.- 1 February 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (2)
Behavior of Brick–Mortar Interfaces in FRP-Strengthened Masonry Assemblages under Normal Loading and Shear Loading
Determination of shear strength of brick–mortar bed joint is critical to overcome the sliding-shear or joint-shear failure in masonry. In the recent past, researchers have attempted to enhance the shear strength and deformation capacity of brick–mortar bed joints by gluing fiber-reinforced polymer (FRP) composite across the bed joint. FRP composites offer several advantages like high strength-to-weight ratio, and ease of application in terms of labor, time, and reduced curing period. Furthermore, FRP composites are desirable for strengthening old masonry buildings having heritage value because of its minimal interference with the existing architecture. A majority of earlier studies on shear strengthening of masonry available in the literature adopted masonry having the ratio of modulus of elasticity of masonry unit (Emu) to modulus of elasticity of mortar (Em) greater than one. Information related to shear behavior of FRP glued masonry composed of masonry units having Young’s modulus lower than mo...
- 1 February 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (2)
Behavior of Brick–Mortar Interfaces in FRP-Strengthened Masonry Assemblages under Normal Loading and Shear Loading
Determination of shear strength of brick–mortar bed joint is critical to overcome the sliding-shear or joint-shear failure in masonry. In the recent past, researchers have attempted to enhance the shear strength and deformation capacity of brick–mortar bed joints by gluing fiber-reinforced polymer (FRP) composite across the bed joint. FRP composites offer several advantages like high strength-to-weight ratio, and ease of application in terms of labor, time, and reduced curing period. Furthermore, FRP composites are desirable for strengthening old masonry buildings having heritage value because of its minimal interference with the existing architecture. A majority of earlier studies on shear strengthening of masonry available in the literature adopted masonry having the ratio of modulus of elasticity of masonry unit (Emu) to modulus of elasticity of mortar (Em) greater than one. Information related to shear behavior of FRP glued masonry composed of masonry units having Young’s modulus lower than mo...
- 1 October 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 21 (10) , 535-542
Influence of Joint Thickness and Mortar-Block Elastic Properties on the Strength and Stresses Developed in Soil-Cement Block Masonry
Soil-cement blocks are employed for load bearing masonry buildings. This paper deals with the study on the influence of bed joint thickness and elastic properties of the soil-cement blocks, and the mortar on the strength and behavior of soil-cement block masonry prisms. Influence of joint thickness on compressive strength has been examined through an experimental program. The nature of stresses developed and their distribution, in the block and the mortar of the soil-cement block masonry prism under compression, has been analyzed by an elastic analysis using FEM. Influence of various parameters like joint thickness, ratio of block to mortar modulus, and Poisson’s ratio of the block and the mortar are considered in FEM analysis. Some of the major conclusions of the study are: (1) masonry compressive strength is sensitive to the ratio of modulus of block to that of the mortar ( Eb / Em ) and masonry compressive strength decreases as the mortar joint thickness is increased for the case where the ratio of blo...
- 1 October 2009
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 21 (10) , 535-542
Influence of Joint Thickness and Mortar-Block Elastic Properties on the Strength and Stresses Developed in Soil-Cement Block Masonry
Soil-cement blocks are employed for load bearing masonry buildings. This paper deals with the study on the influence of bed joint thickness and elastic properties of the soil-cement blocks, and the mortar on the strength and behavior of soil-cement block masonry prisms. Influence of joint thickness on compressive strength has been examined through an experimental program. The nature of stresses developed and their distribution, in the block and the mortar of the soil-cement block masonry prism under compression, has been analyzed by an elastic analysis using FEM. Influence of various parameters like joint thickness, ratio of block to mortar modulus, and Poisson’s ratio of the block and the mortar are considered in FEM analysis. Some of the major conclusions of the study are: (1) masonry compressive strength is sensitive to the ratio of modulus of block to that of the mortar ( Eb / Em ) and masonry compressive strength decreases as the mortar joint thickness is increased for the case where the ratio of blo...
- 1 February 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (2) , 164-172
Enhancing Bond Strength and Characteristics of Soil-Cement Block Masonry
Soil-cement blocks are used for the load bearing masonry of 2–3-story buildings. Flexural and shear strength of such walls greatly depend upon the bond strength between the block and the mortar. This paper deals with the methods of improving the shear-bond strength of soil-cement block masonry (without altering the mortar characteristics) and the influence of shear-bond strength on masonry compressive strength. Altering the texture of bed faces of the block, size and area of the frog, and certain surface coatings have been attempted to enhance the shear-bond strength. The results indicate that: (1) rough textured bed face of the blocks yields higher shear-bond strength than the plain surface; (2) use of fresh cement-slurry coating on the bed faces improves the shear-bond strength considerably; (3) no significant changes are noticed in the compressive strength and stress-strain characteristics of soil-cement block masonry due to changes in shear-bond strength; and (4) masonry has a higher straining capacit...
- 1 February 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (2) , 164-172
Enhancing Bond Strength and Characteristics of Soil-Cement Block Masonry
Soil-cement blocks are used for the load bearing masonry of 2–3-story buildings. Flexural and shear strength of such walls greatly depend upon the bond strength between the block and the mortar. This paper deals with the methods of improving the shear-bond strength of soil-cement block masonry (without altering the mortar characteristics) and the influence of shear-bond strength on masonry compressive strength. Altering the texture of bed faces of the block, size and area of the frog, and certain surface coatings have been attempted to enhance the shear-bond strength. The results indicate that: (1) rough textured bed face of the blocks yields higher shear-bond strength than the plain surface; (2) use of fresh cement-slurry coating on the bed faces improves the shear-bond strength considerably; (3) no significant changes are noticed in the compressive strength and stress-strain characteristics of soil-cement block masonry due to changes in shear-bond strength; and (4) masonry has a higher straining capacit...
- 1 February 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (2) , 139-148
Optimum Soil Grading for the Soil-Cement Blocks
Large numbers of soil-cement block masonry buildings exist in India and many other countries. The paper deals with an experimental study on the influence of soil grading on the characteristics of soil-cement blocks and shear-bond strength of soil-cement block masonry triplets. Influence of clay content of the soil-cement block on strength, absorption and durability characteristics, and interfacial mortar-block bond strength has been examined. Some of the major conclusions of the study are: (1) optimum clay content leading to maximum strength is in the range of 14–16%; (2) saturated water content of the blocks increases with increase in clay content of the block; (3) initial rate of absorption decreases with increase in clay content of the block; (4) weight loss after ASTM wire scratch test is minimum when the clay content of the block is about 16%; and (5) optimum clay content for the highest modulus for the blocks and for highest shear-bond strength is about 16%.
- 1 February 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 19 (2) , 139-148
Optimum Soil Grading for the Soil-Cement Blocks
Large numbers of soil-cement block masonry buildings exist in India and many other countries. The paper deals with an experimental study on the influence of soil grading on the characteristics of soil-cement blocks and shear-bond strength of soil-cement block masonry triplets. Influence of clay content of the soil-cement block on strength, absorption and durability characteristics, and interfacial mortar-block bond strength has been examined. Some of the major conclusions of the study are: (1) optimum clay content leading to maximum strength is in the range of 14–16%; (2) saturated water content of the blocks increases with increase in clay content of the block; (3) initial rate of absorption decreases with increase in clay content of the block; (4) weight loss after ASTM wire scratch test is minimum when the clay content of the block is about 16%; and (5) optimum clay content for the highest modulus for the blocks and for highest shear-bond strength is about 16%.
- 13 July 2006
- Published by Springer Nature in Materials and Structures
- Vol. 40 (2) , 241-253
Strength and elasticity of brick masonry prisms and wallettes under compression
- 13 July 2006
- Published by Springer Nature in Materials and Structures
- Vol. 40 (2) , 241-253
Strength and elasticity of brick masonry prisms and wallettes under compression