Woo-Sang Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Woo-Sang Lee has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Young Joong Yoon
Department of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
4 shared publications - Hong Soo Park
Korea Electrotechnology Research Institute (KERI)
2 shared publications - Jin-Soo Choi
Agency for Defense Development, Daejeon, South Korea
2 shared publications Joon-Ho So
Agency for Defense Development (ADD), Daejeon, South Korea
2 shared publicationsSang-Heun Lee
2 shared publications- Sun K. Hong
Soongsil University
2 shared publications
Latest Publications
- Open Access
- 31 July 2026
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 26 (4) , 385-394
Simulation and Experimental Validation of Electromagnetic Noise from a PFN-Marx Generator in High-Power Microwave Systems
Electromagnetic (EM) noise from a gigawatt-level pulse-forming-network (PFN) Marx generator in a high-power microwave (HPM) system is investigated through both simulation and experiment. Using CST Studio Suite, EM noise was analyzed in terms of emission locations and spectral characteristics. The results show that noise is primarily generated within the PFN-Marx generator and transmission line, and radiates externally through insulator plates. Frequency spectrum analysis indicates distinct peaks below 1.5 GHz, with field strengths on the order of tens of V/m at a distance of 1 m. Experimental measurements conducted on the same model exhibited good agreement with the CST simulations, confirming the reliability of the modeling approach. In addition, simple metallic shields applied to the model suppressed the dominant low-frequency peaks, leaving weaker high-frequency components around 12.8 GHz with magnitudes of several tens of mV/m as residual emission. This work provides one of the few experimental validations of CST-based EM noise modeling for PFN-Marx generators and demonstrates that a validated, geometry-based simulation approach can serve as a practical tool for evaluating electromagnetic interference characteristics and shielding effectiveness in HPM system design.
- 31 July 2026
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 26 (4) , 385-394
Open AccessSimulation and Experimental Validation of Electromagnetic Noise from a PFN-Marx Generator in High-Power Microwave Systems
Electromagnetic (EM) noise from a gigawatt-level pulse-forming-network (PFN) Marx generator in a high-power microwave (HPM) system is investigated through both simulation and experiment. Using CST Studio Suite, EM noise was analyzed in terms of emission locations and spectral characteristics. The results show that noise is primarily generated within the PFN-Marx generator and transmission line, and radiates externally through insulator plates. Frequency spectrum analysis indicates distinct peaks below 1.5 GHz, with field strengths on the order of tens of V/m at a distance of 1 m. Experimental measurements conducted on the same model exhibited good agreement with the CST simulations, confirming the reliability of the modeling approach. In addition, simple metallic shields applied to the model suppressed the dominant low-frequency peaks, leaving weaker high-frequency components around 12.8 GHz with magnitudes of several tens of mV/m as residual emission. This work provides one of the few experimental validations of CST-based EM noise modeling for PFN-Marx generators and demonstrates that a validated, geometry-based simulation approach can serve as a practical tool for evaluating electromagnetic interference characteristics and shielding effectiveness in HPM system design.
- 26 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 68 (2) , 346-355
Target Effect Prediction Using the Random Coupling Model in Complex Electromagnetic Environments
When electronic systems within enclosures are exposed to high-power electromagnetic fields, functional disruption or damage may occur, highlighting the need for predictive models that assess the likelihood of such effects in advance. In enclosure-based scenarios, where the geometry is complex and large relative to the wavelength, electromagnetic field coupling exhibits significant variability. In addition, the susceptibility of electronic devices is uncertain, making deterministic prediction difficult and motivating the need for a stochastic modeling approach. This article presents a framework that combines random coupling model-based statistical predictions of coupled power at the target port with a threshold distribution obtained through direct-injection measurements, where the limited data are fitted using a Weibull model. The proposed method is validated through experimental measurements in a wave-chaotic cavity, with comparisons based on Monte Carlo simulation, bootstrap resampling, and two-sided p-value analysis. The close agreement between the predicted and measured outcomes confirms the capability of the framework to reliably estimate target effect probabilities in complex electromagnetic environments.
- 26 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 68 (2) , 346-355
Target Effect Prediction Using the Random Coupling Model in Complex Electromagnetic Environments
When electronic systems within enclosures are exposed to high-power electromagnetic fields, functional disruption or damage may occur, highlighting the need for predictive models that assess the likelihood of such effects in advance. In enclosure-based scenarios, where the geometry is complex and large relative to the wavelength, electromagnetic field coupling exhibits significant variability. In addition, the susceptibility of electronic devices is uncertain, making deterministic prediction difficult and motivating the need for a stochastic modeling approach. This article presents a framework that combines random coupling model-based statistical predictions of coupled power at the target port with a threshold distribution obtained through direct-injection measurements, where the limited data are fitted using a Weibull model. The proposed method is validated through experimental measurements in a wave-chaotic cavity, with comparisons based on Monte Carlo simulation, bootstrap resampling, and two-sided p-value analysis. The close agreement between the predicted and measured outcomes confirms the capability of the framework to reliably estimate target effect probabilities in complex electromagnetic environments.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (2) , 473-482
Prediction of Electromagnetic Coupling in Complicated Enclosures With External Excitation Through an Aperture Using Extended Random Coupling Model
For the prediction of electromagnetic (EM) coupling in a complex (wave-chaotic) enclosure, the random coupling model (RCM) has proven useful. The applicability of RCM has been demonstrated using various complex enclosures, but their reported validations are mostly with the input and output ports placed within the enclosure. However, since many practical scenarios consist of EM coupling through an aperture of the enclosure from external sources, an extension of the RCM to accommodate such scenarios would be of interest. In this article, we present an extended RCM approach that provides an effective statistical prediction of EM coupling in a complex enclosure for an aperture excitation scenario. Here, we treat the entire wave propagation paths as a cascaded system of two-port networks with an analysis of the aperture using the transmission line theory. This allows us to accurately extract the cavity-specific loss parameter which is required for the RCM prediction of EM coupling, even for an aperture excitation scenario. The overall experimental results suggest that the statistics of the voltages induced on the target port inside the cavity are accurately predictable even in the case of aperture excitation.
- 12 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (2) , 473-482
Prediction of Electromagnetic Coupling in Complicated Enclosures With External Excitation Through an Aperture Using Extended Random Coupling Model
For the prediction of electromagnetic (EM) coupling in a complex (wave-chaotic) enclosure, the random coupling model (RCM) has proven useful. The applicability of RCM has been demonstrated using various complex enclosures, but their reported validations are mostly with the input and output ports placed within the enclosure. However, since many practical scenarios consist of EM coupling through an aperture of the enclosure from external sources, an extension of the RCM to accommodate such scenarios would be of interest. In this article, we present an extended RCM approach that provides an effective statistical prediction of EM coupling in a complex enclosure for an aperture excitation scenario. Here, we treat the entire wave propagation paths as a cascaded system of two-port networks with an analysis of the aperture using the transmission line theory. This allows us to accurately extract the cavity-specific loss parameter which is required for the RCM prediction of EM coupling, even for an aperture excitation scenario. The overall experimental results suggest that the statistics of the voltages induced on the target port inside the cavity are accurately predictable even in the case of aperture excitation.
- 15 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 16 (15361225) , 856-859
A Broadband Dual-Metallic-Reflectarray Antenna for Millimeter-Wave Applications
A design methodology for a broadband dual millimeter-wave reflectarray antenna composed of non-resonant conductor cell is presented. Based on the analysis on the reflection and diffraction phenomenon of the metallic cell with variable height, we confirm that it can be an effective solution as a broadband reflectarray operating at millimeter-wave region. A dual metallic reflectarray composed of a curved sub-reflector and a main reflectarray with diameter of 100 mm is designed at the target center frequency of 94 GHz. The designed dual reflectarray antenna shows a 1-dB gain bandwidth of 10 GHz and quiet uniform radiation pattern at that bandwidth.
- 15 September 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 16 (15361225) , 856-859
A Broadband Dual-Metallic-Reflectarray Antenna for Millimeter-Wave Applications
A design methodology for a broadband dual millimeter-wave reflectarray antenna composed of non-resonant conductor cell is presented. Based on the analysis on the reflection and diffraction phenomenon of the metallic cell with variable height, we confirm that it can be an effective solution as a broadband reflectarray operating at millimeter-wave region. A dual metallic reflectarray composed of a curved sub-reflector and a main reflectarray with diameter of 100 mm is designed at the target center frequency of 94 GHz. The designed dual reflectarray antenna shows a 1-dB gain bandwidth of 10 GHz and quiet uniform radiation pattern at that bandwidth.
- 12 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 63 (2) , 814-818
Square Ring Element Reflectarrays With Improved Radiation Characteristics by Reducing Reflection Phase Sensitivity
A reflectarray with square ring (SR) elements that are designed to reduce the reflection phase sensitivity on a thin substrate is proposed. Generally, the SR element is designed with a fixed ring width, or a fixed ratio between the ring width and the outer length of the ring. However, it is difficult to obtain both a reflection phase range close to 360° and sufficiently low phase sensitivity simultaneously with the conventional methods. Thus, a modified design method to reduce the phase sensitivity without sacrificing the phase range by introducing two procedures (changing the outer and inner lengths of the ring in opposite directions, and changing the inner length while fixing the outer length) is proposed to design a reflectarray on a 0.039λ 0 thick substrate at 15 GHz. The radiation characteristics of the reflectarray designed with the proposed method are compared to those of the conventionally designed SR element reflectarray, and gain enhancement of 2.2 dB is achieved at 15 GHz.
- 12 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 63 (2) , 814-818
Square Ring Element Reflectarrays With Improved Radiation Characteristics by Reducing Reflection Phase Sensitivity
A reflectarray with square ring (SR) elements that are designed to reduce the reflection phase sensitivity on a thin substrate is proposed. Generally, the SR element is designed with a fixed ring width, or a fixed ratio between the ring width and the outer length of the ring. However, it is difficult to obtain both a reflection phase range close to 360° and sufficiently low phase sensitivity simultaneously with the conventional methods. Thus, a modified design method to reduce the phase sensitivity without sacrificing the phase range by introducing two procedures (changing the outer and inner lengths of the ring in opposite directions, and changing the inner length while fixing the outer length) is proposed to design a reflectarray on a 0.039λ 0 thick substrate at 15 GHz. The radiation characteristics of the reflectarray designed with the proposed method are compared to those of the conventionally designed SR element reflectarray, and gain enhancement of 2.2 dB is achieved at 15 GHz.
- 30 November 2008
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 19 (11) , 1185-1192
A Study on Wideband LC Oscillator Using Fat Dipole Antenna
- 30 November 2008
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 19 (11) , 1185-1192
A Study on Wideband LC Oscillator Using Fat Dipole Antenna
- 30 September 2008
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 19 (9) , 947-956
Miniaturized Conically Stepped COBRA for High Power Electromagnetic Generator
- 30 September 2008
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 19 (9) , 947-956
Miniaturized Conically Stepped COBRA for High Power Electromagnetic Generator