Raviteja Theertham
Research Subjects
Research Interests
Raviteja Theertham has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Shanthi Pavan
Indian Institute of Technology Madras, Chennai, India
2 shared publications - Prasanth Koottala
Department of Electrical Engineering, IIT Madras, Chennai 600036, India
1 shared publication Satya Narayana Ganta
MediaTek, Hsinchu, Taiwan
1 shared publicationSujith Billa
Department of Electrical Engineering, IIT Madras, Chennai 600036, India
1 shared publication
Latest Publications
- 8 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (11) , 3418-3428
Design of High-Resolution Continuous-Time Delta–Sigma Data Converters With Dual Return-to-Open DACs
We present design techniques for single-bit continuous-time delta–sigma modulators that attain high resolution ($>$ 16 bits) over a bandwidth (BW) that is more than ten times the audio range. We introduce the zapped, virtual-ground-switched dual return-to-open DAC which is immune to ISI and other transition-dependent errors. FIR feedback facilitates chopping, improves clock-jitter sensitivity and the loop filter’s linearity. We show that the compensation FIR DAC, which is typically bulky, can be implemented in an extremely power-and area-efficient manner in a single-bit modulator using a capacitive DAC and passive summation. Thanks to these techniques, the fabricated prototype achieves 103.2-/104.3-dB signal to noise and distortion ratio (SNDR)/signal to noise ratio (SNR) in a 250-kHz bandwidth while operating at 48 MS/s. Consuming 17.7 mW from a 1.8-V supply, the modulator occupies 1.1 mm² in a 180-nm CMOS process. The Schreier (SNDR) figure of merit (FoM) is 174.7 dB.- 8 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (11) , 3418-3428
Design of High-Resolution Continuous-Time Delta–Sigma Data Converters With Dual Return-to-Open DACs
We present design techniques for single-bit continuous-time delta–sigma modulators that attain high resolution ($>$ 16 bits) over a bandwidth (BW) that is more than ten times the audio range. We introduce the zapped, virtual-ground-switched dual return-to-open DAC which is immune to ISI and other transition-dependent errors. FIR feedback facilitates chopping, improves clock-jitter sensitivity and the loop filter’s linearity. We show that the compensation FIR DAC, which is typically bulky, can be implemented in an extremely power-and area-efficient manner in a single-bit modulator using a capacitive DAC and passive summation. Thanks to these techniques, the fabricated prototype achieves 103.2-/104.3-dB signal to noise and distortion ratio (SNDR)/signal to noise ratio (SNR) in a 250-kHz bandwidth while operating at 48 MS/s. Consuming 17.7 mW from a 1.8-V supply, the modulator occupies 1.1 mm² in a 180-nm CMOS process. The Schreier (SNDR) figure of merit (FoM) is 174.7 dB.- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (9) , 2429-2442
Design Techniques for High-Resolution Continuous-Time Delta–Sigma Converters With Low In-Band Noise Spectral Density
We present design considerations for CT∆ΣM that attempt to achieve high resolution (16+ bits) over a wide bandwidth (>200 kHz), resulting in a low in-band noise spectral density. The main challenges in such designs are parasitic resistance in the reference path, inter-symbol interference (ISI) in the feedback-digital-to-analog converter (DAC) waveform, and flicker noise of the input operational transconductance amplifier (OTA). We introduce the virtual-ground-switched resistor DAC as a way to achieve low distortion by addressing parasitic resistance in the reference path and reducing the effects of ISI. Flicker noise is reduced by chopping the first stage of the input OTA. Chopping artifacts and clock jitter sensitivity are reduced by using a three-stage OTA and finite impulse response (FIR) feedback. These techniques are applied to the design of a 250 kHz bandwidth CT∆ΣM targeting 108 dB signal-to-noise-and-distortion-ratio (SNDR) in a 180 nm CMOS process. The fabricated prototype, which operates at 32 MS/s, achieves 105.3/108.1 dB SNDR/signal-to-noise-ratio (SNR) and consumes 24 mW. The Schreier SNDR figure of merit (FoM) is 175.5 dB.
- 30 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (9) , 2429-2442
Design Techniques for High-Resolution Continuous-Time Delta–Sigma Converters With Low In-Band Noise Spectral Density
We present design considerations for CT∆ΣM that attempt to achieve high resolution (16+ bits) over a wide bandwidth (>200 kHz), resulting in a low in-band noise spectral density. The main challenges in such designs are parasitic resistance in the reference path, inter-symbol interference (ISI) in the feedback-digital-to-analog converter (DAC) waveform, and flicker noise of the input operational transconductance amplifier (OTA). We introduce the virtual-ground-switched resistor DAC as a way to achieve low distortion by addressing parasitic resistance in the reference path and reducing the effects of ISI. Flicker noise is reduced by chopping the first stage of the input OTA. Chopping artifacts and clock jitter sensitivity are reduced by using a three-stage OTA and finite impulse response (FIR) feedback. These techniques are applied to the design of a 250 kHz bandwidth CT∆ΣM targeting 108 dB signal-to-noise-and-distortion-ratio (SNDR) in a 180 nm CMOS process. The fabricated prototype, which operates at 32 MS/s, achieves 105.3/108.1 dB SNDR/signal-to-noise-ratio (SNR) and consumes 24 mW. The Schreier SNDR figure of merit (FoM) is 175.5 dB.