Brian Gibson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Brian Gibson has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
A. Ma
University of California at Santa Barbara 1 Department of Mechanical Engineering Santa Barbara, California 93106, USA
1 shared publicationB. S. Strachan
Michigan State University 2 Department of Mechanical Engineering East Lansing, Michigan 48823, USA
1 shared publicationCristian Cassella
Department of Electrical Engineering, Northeastern University, Boston, MA, USA
1 shared publicationGianluca Piazza
Department of Electrical Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
1 shared publicationK. L. Turner
University of California at Santa Barbara 1 Department of Mechanical Engineering Santa Barbara, California 93106, USA
1 shared publicationKamala Qalandar
Department of Mechanical Engineering, University of California Santa Barbara, Santa Barbara, CA, USA
1 shared publication
Latest Publications
- 15 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 64 (5) , 898-904
A Study on the Effects of Release Area on the Quality Factor of Contour-Mode Resonators by Laser Doppler Vibrometry
Through the use of a laser Doppler vibrometer, it is shown that a 31% variation in quality factor can occur due to the effect of undercutting of the device layers outside of the anchors of a 220-MHz aluminum nitride contour-mode resonator. This undercutting is a result of the isotropic etch process used to release the device from the substrate. This paper shows that the variation in Q is a function of the release distance, L , between the active region of the resonator and the edge of this released region. This paper also determined a design modification that eliminated this issue and achieved a Q of 3048, which is independent of L .
- 15 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 64 (5) , 898-904
A Study on the Effects of Release Area on the Quality Factor of Contour-Mode Resonators by Laser Doppler Vibrometry
Through the use of a laser Doppler vibrometer, it is shown that a 31% variation in quality factor can occur due to the effect of undercutting of the device layers outside of the anchors of a 220-MHz aluminum nitride contour-mode resonator. This undercutting is a result of the isotropic etch process used to release the device from the substrate. This paper shows that the variation in Q is a function of the release distance, L , between the active region of the resonator and the edge of this released region. This paper also determined a design modification that eliminated this issue and achieved a Q of 3048, which is independent of L .
- 15 December 2014
- Published by AIP Publishing in Applied Physics Letters
- Vol. 105 (24) , 244103
Frequency division using a micromechanical resonance cascade
A coupled micromechanical resonator array demonstrates a mechanical realization of multi-stage frequency division. The mechanical structure consists of a set of N sequentially perpendicular microbeams that are connected by relatively weak elastic elements such that the system vibration modes are localized to individual microbeams and have natural frequencies with ratios close to 1:2:⋯:2N. Conservative (passive) nonlinear inter-modal coupling provides the required energy transfer between modes and is achieved by finite deformation kinematics. When the highest frequency beam is excited, this arrangement promotes a cascade of subharmonic resonances that achieve frequency division of 2j at microbeam j for j = 1, …, N. Results are shown for a capacitively driven three-stage divider in which an input signal of 824 kHz is passively divided through three modal stages, producing signals at 412 kHz, 206 kHz, and 103 kHz. The system modes are characterized and used to delineate the range of AC input voltages and frequencies over which the cascade occurs. This narrow band frequency divider has simple design rules that are scalable to higher frequencies and can be extended to a larger number of modal stages.
- 15 December 2014
- Published by AIP Publishing in Applied Physics Letters
- Vol. 105 (24) , 244103
Frequency division using a micromechanical resonance cascade
A coupled micromechanical resonator array demonstrates a mechanical realization of multi-stage frequency division. The mechanical structure consists of a set of N sequentially perpendicular microbeams that are connected by relatively weak elastic elements such that the system vibration modes are localized to individual microbeams and have natural frequencies with ratios close to 1:2:⋯:2N. Conservative (passive) nonlinear inter-modal coupling provides the required energy transfer between modes and is achieved by finite deformation kinematics. When the highest frequency beam is excited, this arrangement promotes a cascade of subharmonic resonances that achieve frequency division of 2j at microbeam j for j = 1, …, N. Results are shown for a capacitively driven three-stage divider in which an input signal of 824 kHz is passively divided through three modal stages, producing signals at 412 kHz, 206 kHz, and 103 kHz. The system modes are characterized and used to delineate the range of AC input voltages and frequencies over which the cascade occurs. This narrow band frequency divider has simple design rules that are scalable to higher frequencies and can be extended to a larger number of modal stages.