Jakub Smiraus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jakub Smiraus has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Aleš Slíva
Faculty of Mechanical Engineering, VSB–Technical University of Ostrava, 17. listopadu 15/2172, 70800 Ostrava, Czech Republic
2 shared publications - Jakub Mesicek
Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, 708 00 Ostrava, Czech Republic
2 shared publications - Jan Famfulik
VSB Tech Univ Ostrava, Fac Mech Engn, Inst Transport, 17 Listopadu 15, Ostrava 70800, Czech Republic
2 shared publications - Petra Muckova
VSB Tech Univ Ostrava, Inst Transport, Fac Mech Engn, 17 Listopadu 15, Ostrava 70800, Czech Republic
2 shared publications - Quoc-Phu Ma
Faculty of Mechanical Engineering, VSB—Technical University of Ostrava, 70800 Ostrava, Czech Republic
2 shared publications - Aleksandra Mikulikova
Silesian University of Technology
1 shared publication
Latest Publications
- Open Access
Topology Optimization of the Clutch Lever Manufactured by Additive Manufacturing
This article aims to review a redesign approach of a student racing car’s clutch lever component, which was topologically optimized and manufactured by Additive Manufacturing (AM). Finite Element Method (FEM) analysis was conducted before and after a Topology Optimization (TO) process in order to achieve equivalent stiffness and the desired safety factor for the optimized part. The redesigned clutch lever was manufactured by using AM–Selective Laser Melting (SLM) and printed from powdered aluminum alloy AlSi10Mg. The final evaluation of the study deals with the experimental test and comparison of the redesigned clutch lever with the existing part which was used in the previous racing car. Using TO as a main redesign tool and AM brought significant changes to the optimized part, especially the following: reduced mass of the component (10%), increased stiffness, kept safety factor above the 3.0 value and ensured the more aesthetic design and a good surface quality. Moreover, using TO and AM gave the opportunity to consolidate multi-part assembly into a single component manufactured by one manufacturing process that reduced the production time. The experimental results justified the simulation results and proved that even though the applied load was almost 1.5× higher than the assumed one, the maximum von Mises stress on the component was still below the yield limit of 220 MPa.
Open AccessTopology Optimization of the Clutch Lever Manufactured by Additive Manufacturing
This article aims to review a redesign approach of a student racing car’s clutch lever component, which was topologically optimized and manufactured by Additive Manufacturing (AM). Finite Element Method (FEM) analysis was conducted before and after a Topology Optimization (TO) process in order to achieve equivalent stiffness and the desired safety factor for the optimized part. The redesigned clutch lever was manufactured by using AM–Selective Laser Melting (SLM) and printed from powdered aluminum alloy AlSi10Mg. The final evaluation of the study deals with the experimental test and comparison of the redesigned clutch lever with the existing part which was used in the previous racing car. Using TO as a main redesign tool and AM brought significant changes to the optimized part, especially the following: reduced mass of the component (10%), increased stiffness, kept safety factor above the 3.0 value and ensured the more aesthetic design and a good surface quality. Moreover, using TO and AM gave the opportunity to consolidate multi-part assembly into a single component manufactured by one manufacturing process that reduced the production time. The experimental results justified the simulation results and proved that even though the applied load was almost 1.5× higher than the assumed one, the maximum von Mises stress on the component was still below the yield limit of 220 MPa.
- 8 March 2023
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2023 (1) , 6364-6367
ENGINE INTAKE AIRBOX CFD OPTIMISATION AND EXPERIMENTAL VALIDATION TESTS
The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...
- 8 March 2023
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2023 (1) , 6364-6367
ENGINE INTAKE AIRBOX CFD OPTIMISATION AND EXPERIMENTAL VALIDATION TESTS
The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5421-5425
THE COMBUSTION ENGINE INTAKE MANIFOLD CFD MODELING DEPENDING ON THE AIRBOX CONFIGURATION
The aim of the article is to present the possibilities of application of computational fluid dynamics (CFD) to modelling of air flow in combustion engine intake manifold depending on airbox configuration. The non-stationary flow occurs in internal combustion engines. This is a specific type of fl...
- 15 December 2021
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2021 (6) , 5421-5425
THE COMBUSTION ENGINE INTAKE MANIFOLD CFD MODELING DEPENDING ON THE AIRBOX CONFIGURATION
The aim of the article is to present the possibilities of application of computational fluid dynamics (CFD) to modelling of air flow in combustion engine intake manifold depending on airbox configuration. The non-stationary flow occurs in internal combustion engines. This is a specific type of fl...
- Open Access
On Aluminum Honeycomb Impact Attenuator Designs for Formula Student Competitions
The use of impact attenuators (IA) is important for vehicles as they absorb the kinetic energy exerted from the car crashes to protect the drivers from any possible injuries. Under the framework of the Formula Student (FS) competition, we investigate various designs of IA made of aluminum honeycomb material. Specifically, the crushing behavior of the honeycomb structure is investigated from the theoretical point of view and later verified with numerical simulations. To achieve the desired crushing behavior of the aluminum honeycomb structure, apart from the so-called pre-crushing method, another way to pre-process the aluminum honeycomb is proposed. Modification on the aluminum honeycomb is done in a symmetric manner to ensure the same uniform crushing behavior on the two sides of the mirror plane of the car. Different variations presented in this paper shed a light on future aluminum honeycomb IA designs in the context of FS competitions.
Open AccessOn Aluminum Honeycomb Impact Attenuator Designs for Formula Student Competitions
The use of impact attenuators (IA) is important for vehicles as they absorb the kinetic energy exerted from the car crashes to protect the drivers from any possible injuries. Under the framework of the Formula Student (FS) competition, we investigate various designs of IA made of aluminum honeycomb material. Specifically, the crushing behavior of the honeycomb structure is investigated from the theoretical point of view and later verified with numerical simulations. To achieve the desired crushing behavior of the aluminum honeycomb structure, apart from the so-called pre-crushing method, another way to pre-process the aluminum honeycomb is proposed. Modification on the aluminum honeycomb is done in a symmetric manner to ensure the same uniform crushing behavior on the two sides of the mirror plane of the car. Different variations presented in this paper shed a light on future aluminum honeycomb IA designs in the context of FS competitions.