PLPeiqi Liu

Peiqi Liu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Peiqi Liu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:

  • B. Han

    Dalian Boiler and pressure vessel inspection and Testing Institute Co., Ltd, Dalian, China

    1 shared publication
  • C. Zhu

    Institute of Chemical Engineering, Dalian University of Technology, Dalian, China

    1 shared publication
  • Che Zhu

    Institute of Chemical Engineering, Dalian University of Technology, Dalian 116024, Liaoning, China

    1 shared publication
  • D. Hu

    Institute of Chemical Engineering, Dalian University of Technology, Dalian, China

    1 shared publication
  • DaPeng Hu

    Frontier Science Center for Smart Materials, Dalian University of Technology, Dalian, China

    1 shared publication
  • Dapeng Hu

    State Key Laboratory of Fine Chemicals, Frontier Science Center for Smart Materials, School of Chemical Engineering, Dalian University of Technology, Dalian 116024, China

    1 shared publication

Latest Publications

  • Open Access

    A Fluid-Mechanism-and-Differential-Evolution-Enhanced Particle Swarm Optimizer for Robot Path Planning

    by Zixiang Wang, Zijie Nie, Peiqi Liu

    Path planning of mobile robots on grid maps is a complex optimization problem, and applying standard particle swarm optimization (PSO) to this task often leads to stagnation and premature convergence. To address these issues, a particle swarm optimizer enhanced by fluid mechanics and differential evolution (FMDEPSO) is proposed. The method integrates fluid-inspired neighborhood feedback with a differential evolution recombination mechanism to construct a semi-discrete population evolution framework. Specifically, FMDEPSO introduces a pressure repulsion term and a viscous diffusion term to mitigate early population collapse and suppress oscillations caused by abrupt velocity variations. Meanwhile, a gas–liquid phased adaptive scheduling strategy is adopted to dynamically adjust the learning factors, thereby balancing exploration and exploitation. In addition, the mutation–crossover–greedy selection operator of differential evolution (DE) is embedded into the update process to preserve population diversity and enhance the capability of escaping local optima. On the CEC2017 benchmark suite, FMDEPSO achieved the best mean results on 17, 19, and 17 functions under 30-, 50-, and 100-dimensional settings, respectively, compared with eight representative PSO variants. It maintained a top-three ranking on the majority of functions and obtained the overall best average rank according to the Friedman test. The Wilcoxon rank-sum test further confirmed its statistical advantage on most benchmark functions. In grid-based path-planning experiments on multi-scale environments (20×20, 40×40, and 60×60), FMDEPSO generates smooth and goal-directed feasible trajectories in successful runs and achieves the best overall performance among PSO-based methods while maintaining a favorable balance among path quality, success rate, and runtime across different complexity levels. Overall, the proposed method exhibits stable convergence behavior and competitive solution quality in both numerical benchmark optimization and mobile robot path-planning tasks.

  • Effect of Impact Energy on the Residual Strength of Type III Cylinders

    by Y. Zhou, B. Han, Y. Liu, X. Song, T. Xie, F. Geng, P. Liu


  • Investigation of the Shock Wave Formation and Intensity in Wave Rotor

    by Peiqi Liu, Xiang Li, Xinyu Liu, Jun Yang, Mingyu Feng, Dapeng Hu

    Actual formation and intensity of shock wave generated during gradual opening and closure between each port and passages of wave rotor are studied by means of experiment and computational fluid dynamics simulation. The results show that the intensity of shock wave increases with the distance from high-pressure inlet, and the reason for the variation tendency is the superposition of compression waves. By changing the rotational speed and the expansion ratio, the shock wave intensity can be adjusted, but the position where the intensity reaches maximum stays constant basically and keeps the distance near 300 mm from high-pressure inlet. Comparing with the one-dimensional simplification result, the actual intensity of shock wave is lower. The difference between the fact and simplification increases with the rotational speed and expansion ratio. The internal mechanism has been analyzed from the aspect of intake mass. Then, the maximum shock wave intensity is found approximately linear to the intake mass of each rotor passage in each cycle.


  • Improving Refrigeration Performance by Using Pressure Exchange Characteristic of Wave Rotor

    by Dapeng Hu, Yang Yu, Peiqi Liu, Xiaolin Wu, Yiming Zhao

    Wave rotor with pressure exchange function can be attempted to improve refrigeration performance. The objective of this paper is to verify the feasibility of the method by thermodynamic and experimental analysis. First, a refrigeration process which contains wave rotor pressurization was established. Then, a thermodynamic model which reflects the refrigeration process was designed. The thermal performance was researched under various key parameters. Finally, based on the novel wave rotor refrigeration platform, the experimental work was carried out, and the effects of main parameters of the device were systematically studied. The results showed that it was feasible to enhance the coefficient of performance (COP) by using pressure exchange characteristic of wave rotor. The COP could be improved substantially at relatively small expansion ratio. Under the design point, more than half of the pressure energy could be restored. The performance curve of the novel equipment was also obtained. Enhancing the isentropic efficiency of expansion is the effective means to improve the COP and σ of the system. This paper was designed in a way that contained a novel equipment to enhance the COP of wave rotor refrigeration.


  • Mechanism Analysis of Weakening Reverse Compression Waves in Gas Wave Refrigerator

    by Peiqi Liu, Kehan Wu, Sheng Liu, Wenhu Tan, Che Zhu, Dapeng Hu

    Pressure oscillating tubes are core components of the gas wave refrigerator. The reverse compression waves will limit refrigeration efficiency by reheat cooling gas. The promotion from traditional rotation gas wave refrigerator with single opened pressure oscillating tubes to the streamlined pressure exchange gas wave refrigerator with double opened pressure oscillating tubes is mainly in terms of this issue. However, through weakened, reverse compression waves are still inevitable. For further development, the concept of a wave attenuator has been proposed, installed at the high-temperature (HT) port. Numerical simulation has been utilized to analyze mechanism of wave attenuator and the practical effect has been proved by experiment research. The conclusions are as follows: due to structure of wave attenuator, the intensity of reverse compression waves has been weakened; the optimal structure of wave attenuator has been obtained; the refrigeration efficiency of the refrigerator has been significantly increased because of wave attenuator in HT port.


  • Influence of the nozzle angle on refrigeration performance of a gas wave refrigerator

    by P. Liu, Y. Zhu, H. Wang, C. Zhu, J. Zou, J. Wu, D. Hu


  • Thermomechanical Analysis of Pressure Vessels With Functionally Graded Material Coating

    by Z. W. Wang, Q. Zhang, L. Z. Xia, J. T. Wu, P. Q. Liu

    Pressure vessels covered with overlaying layer or coating are widely applied due to its strong heat resistance, corrosion resistance, and load-carrying capacity. However, limited work has been reported on investigating the thermomechanical behavior of a pressure vessel with a functionally graded material (FGM) coating. In this study, a closed-form analytical solution was first derived for calculating the stress distribution in a pressure vessel with an FGM coating subjected to an internal pressure and a thermal load. Afterwards, a numerical solution was also established for validating the analytical solution using finite element (FE) method. It was found out that the analytical solution agreed well with the numerical ones, and the thermomechanical properties of FGM coating were also discussed in detail. This work would be helpful for better understanding and scientific design of pressure vessels with an FGM coating or related thin-walled structures.